Kichler Lighting Decor Link Bedienungsanleitung

 2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

54” LinkTM

A Kichler®Décor™ceiling fan

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

HIGH

EFFICIENCY

MOTOR

U.S.

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only ETL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. To operate the reverse function on this

fan, press the reverse button while the fan

is running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the ground wire and white

(common) wire to one side with the black

(load) wire to the other side of the outlet

box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (2)

b. Fan motor assembly

c. CoolTouch™ Control System

d. 4mm Allen wrench

e. Part bag contents

1) Mounting hardware :

wood screws (2), ﬂat washers (2),

star washers (2), wire nuts (3),

screws (2)

2) Blade attachment hardware:

Allen screws with lock washers (9),

ﬁlat washers (9), gaskets (2)

3) Safety cable hardware:

wood screw, lock washer, ﬂat washer

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

54"LinkTM

4. MOUNTING OPTIONS

Outlet box

Fig. 1

Fig. 3

Outlet box

Fig. 2

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 3)

Fig. 6

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Attach the mounting plate to the outlet

box with the screws and washers provided

with the outlet box. Make sure the mounting

plate is tight and secured. (Fig. 5)

Step 2. Hang the fan motor assembly and

use the safety cable attached to the mounting

plate. This will allow you to use both hands

while make the electrical connections. (Fig. 6)

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Remove the mounting plate from the

fan motor by removing the nuts. (Fig. 4)

Fig. 5

Fig. 4

6. HANGING THE FAN

CUL Listed

electrial

box

Mounting plate

5. REMOVE THE MOUNTING PLATE

Mounting

plate

Nut

Fan motor

Safety cable

54"LinkTM

Fig. 7

7. ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire connecting

nuts suppled with your fan. Secure the

connectors with electrical tape. Make sure

there are no loose wire strands or connections.

Step 1. Connect the fan supply (black) wire to

the black household supply wire as shown in

Figure 12.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

and blue wires are on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Ground (green)

(Connect to ground wire

on hanger bracket if no

house ground wire exists.)

Outlet box

Black ("AC IN L")

Black (motor)

Fig. 8

Fig. 9

8. FINISHING THE INSTALLATION

Step 1. Move fan into position over the four

mounting studs and secure with the provided

nuts. (Fig. 8)

Step 2. Raise the motor housing up against

the mounting plate, the four supports inside

the housing should be placed against the four

studs on mounting plate, twist the housing

clockwise until snug. (Fig. 9)

Studs

Motor

housing

Nuts

Screws

54"LinkTM

Fig. 10

9. ATTACHING THE FAN BLADES

Step 1. Attach a blade to a blade bracket with

the Allen screws (with lock washers) and ﬁlat

washers and fasten using the Allen wranch

provided. (Fig. 10)

Place the gasket into blade bracket. Make

sure the blade is straight when set on the

blade bracket. Tighten each mounting screw

and then repeat this procedure for each blade.

Blade

Blade bracket

Allen screws with

lock washers

Allen wrench

Flat washers

Gasket

Fig. 11

Fig. 12

Make sure the power is completely disconnected

before you begin this procedure.

SPECIAL NOTE:

Your new Kichler®Ceiling Fan is State of the Art

and employs a High Efﬁciency DC (direct current)

Motor with an advanced CoolTouch™ Remote

Control System. The DC Motor uses 70% less

energy than a conventional ceiling fan AC

Induction Motor. The DC motor is “Digitally”

controlled and operates differently than

conventional ceiling fans motors. Please read this

portion of the manual completely before

proceeding.

Our CoolTouch™ Control system includes an

“Automatic Frequency Selection” feature. To set

the control frequency and program the control

system, follow these steps.

Open the back of the Transmitter (ﬁgure 11)

The Frequency Selector is a "Dip Switch Block"

inside the Battery compartment of the Transmitter.

(See ﬁgure 18) You change frequencies by

arranging the small switches numbered 1 through

4 in a up or down position. 16 possible

frequencies or combinations are possible.

The ﬁfth switch, marked D and X sets the system

for operation with Incandescent or Fluorescent

Lamps. It is essential to set this switch correctly. If

your ceiling fan is equipped with Incandescent

Lamps set this switch to the D Position, for

Fluorescent Lamps, set the switch to the X

Position. If these settings are reversed, the

lighting control system will operate erratically and

could damage your ceiling fan.

System Programing: Read all of these steps

BEFORE proceeding. Each step must be followed

exactly to properly program the control system.

1. You can leave the frequency switches at the

factory setting or move them to any combination

of up or down. Use a small ﬂat bladed screwdriver

to move the switches.

2. Insert both batteries and make sure they

are seated correctly in each recess with the

Positive + sign facing up. Replace the battery

cover. (Figure 11)

10. CONTROL SYSTEM SET-UP

1 2 3 4

Dip switch

54"LinkTM

Fig. 13

Fig. 14

Blue Light

Press/hold Button

3. Test the transmitter by pushing and releasing

ANY button brieﬂy. A Blue Light should illuminate

under the 3-4 buttons. (Fig. 13) If not, check to

make sure the batteries are inserted and seated

correctly.

Power Up and Programming:

4. Follow the below steps to set the remote control:

The auto learning function will only mandate within

60 seconds when turning the fan’s AC power ON.

(Figure 14)

5. Select desired frequency from the back of

transmitter.

6. From the back of the transmitter, press “ ”

power button for 3 to 5 seconds. Light will blink

twice. The remote will now be programmed to your

fan and ready for use.

Try different speed setting on wall control to ensure

the fan is now fully functional. If programming is

unsuccessful, retry the process starting from step 6

again.

IMPORTANT: Do not interrupt the conditioning

until the fan comes to a complete stop in

approximately 5 minutes. All functions of the

control will be rejected during conditioning.

NOTE: The learning frequency function and self

calibration test will continue to retain the last set

frequency and calibration set even when the AC

power is shut off. If the frequency is changed the

self calibration test will occur again.

7. Your CoolTouch™ Control System is now

programmed and ready for use. Please see the

follow Operational Instructions.

The receiver provides the following protective

function:

1. Lock position: The DC motor has a built-in safety

against obstruction during operation. If there is an

obstruction, the motor will stop and then the power

will automatically go off in 30 seconds. Remove the

obstruction and reset.

2. Over 80W protection: When the receiver detects

motor power consumption which is greater than

80W, the receiver power will be stopped and

operation will immediately discontinue. Wait for 5

seconds and then turn the receiver power back on.

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Lucian II 330241 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Maor 310136 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Patio 310192 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 339211APP Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35157 Bedienungsanleitung

Kichler Lighting

Kichler Lighting XETY LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330174OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sola 330151 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk Bedienungsanleitung

Kichler Lighting

Kichler Lighting Imari 65 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Motu Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Meredith Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Dorset Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bronson Bedienungsanleitung

Kichler Lighting

Kichler Lighting Incus Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cottage Grove Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside Bedienungsanleitung

Kichler Lighting

Kichler Lighting ZEUS KLF-ZEUS-60-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sunburst 300170 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Todo 330025 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Spyn Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300260/60-GENT Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung