Kichler Lighting Jade 300030 Bedienungsanleitung

Instruction Manual

Jade

UL Model #300030xxx

300030

Includes Wall Control

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualied licensed electrician.

3. WARNING: To Reduce The Risk Of Fire Or

Electric Shock, Do Not Use This Fan With

Any Solid-State Speed Control Device. Only

use the remote control provided by ceiling

fan manufacturer.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes

commonly used for the support of lighting

xtures are not acceptable for fan support

and may need to be replaced, consult a

qualied electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of reliably

supporting a minimum of 50 pounds. Use

only CUL Listed outlet boxes marked “FOR

FAN SUPPORT”.

6. The fan must be mounted with a minimum of

7 feet clearance from the trailing edge of the

blades to the oor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned off

and blades stopped before reversing blade

direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the fan

and other items, be cautious when working

around or cleaning the fan.

10. Do not use water or detergents when cleaning

the fan or fan blades. A dry dust cloth or

lightly dampened cloth will be suitable for

most cleaning.

11. After marking electrical connections, spliced

conductors should be turned upward and

pushed carefully up into outlet box. The wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are reference only. Light

Kits that are not packed with the fan must be

CUL Listed and marked suitable for use with

the model fan you are installing. Switches

must be CUL General Use Switches. Refer

to the Instructions packaged with the light

kits and switches for proper assembly.

1. SAFETY RULES (READ AND SAVE THESE INSTRUCTIONS)

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL INJURY,

MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT”

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

WARNING

CHANGES OR MODIFICATIONS TO THIS

UNIT NOT EXPRESSLY APPROVED BY THE

PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

FCC ID: RGB-60ORIR. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

60” Jade

2. TOOLS AND MATERIALS REQUIRED

• Phillips screw driver

• Blade screw driver

• 11mm wrench

• Step ladder

• Wire cutters

3. PACKAGE CONTENTS

Unpack your fan and check the contents.

You should have the following items:

a. Fan blades (3)

b. Canopy, Ceiling mounting bracket

and Canopy bottom cover

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Light kit pan

g. Light kit pan shade

h. Extra non-light cap (for fan without

light kit)

i. Receiver

j. Wall transmitter

k. Parts bag contents:

1) Mounting hardware:

Star washers (2), wire nuts (3),

machine screws (2), washers (2),

wood screws (2)

2) Blade attachment hardware:

screws (10), ber washers (10)

3) Safety cable hardware:

wood screw, lock washer, at

washer

4) Balancing kit

4. MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building structure.

Use appropriate fasteners and building materials. The

outlet box and its support must be able to fully support

the moving weight of the fan (at least 50 lbs). Do not

use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different ways to

mount the outlet box.

NOTE: If you are installing the ceiling fan on a sloped

(vaulted) ceiling, you may need a longer downrod

to maintain proper clearance between the tip of the

blade and the ceiling. A minimum clearance of 12” is

suggested for optimal operation.

NOTE: Depending on the location you have selected

for installation, you may need to purchase and install

a “Joist Hanger” for the support of the outlet box.

Make sure the joist hanger you purchase has been

designed for use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

ANGLED CEILING

MAXIMUM 30°

ANGLE

Fig. 2

Fig. 1

Fig. 3

Fig. 4

60” Jade

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counterclockwise. (Fig.5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing(and save) one of

the two screws. Loosen the remaining screw by

a half turn. (Fig.5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove the hanger ball from the

downrod assembly by loosening the setscrew,

removing the cross pin and turning the ball off

the downrod. (Fig. 7)

Step 6. Loosen the two setscrews and remove

the hitch pin and retaining clip from the coupling

on top of the motor assembly. (Fig. 8)

Step 7. Carefully route the electrical supply

wires and safety cable exiting the top of the fan

motor assembly through the downrod. Thread

the downrod into the coupling until the hitch pin

holes are aligned. (Fig. 8)

Next, replace the hitch pin and retaining clip.

Tighten both setscrews. (Fig. 8)

Fig. 6

Fig. 5

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

UL Listed

outlet box

120V Wires

Washers

Ceiling mounting

bracket

Canopy

Canopy cover

Cross pin

Hanger ball

Set screw

Downrod

Fig. 7

Supply wires

& Safety cable

Downrod

Retaining clip

Hitch pin

Set screws

Coupling

Set screws

Fig. 8

Registration slot

Check tab

Cross pin

Hanger ball

Set screw

Downrod

Coupling

Canopy

Canopy cover

Coupling cover

Supply wires & Safety cable

Step 8. Slip the coupling cover, canopy cover and

canopy onto the downrod. (Fig. 9)

Thread the hanger ball onto the downrod, insert the

cross pin through the downrod and tighten. Now

tighten the set screw. (Fig. 9)

Step 9. Lift the motor assembly into position and

place the hanger ball into the ceiling mounting

bracket.

Rotate the entire assembly until the “Check Tab”

has dropped into the “Registration Slot” and seats

rmly. (Fig. 10)

The entire motor assembly should not rotate (left or

right) when seated properly.

WARNING: Failure to reattach the cross pin and

seat the “Check Tab” can cause the fan to fall from

the ceiling during operation. Take special care to

make sure this pin is reattached.

Fig. 9

Fig. 10

60” Jade

Code switch

MED

LOW

FAN OFF

ON ECE

1 2 3 4

ON ECE

1234

Receiver Hanger

bracket

Hanger bracket

Safety cable Attach safety cable

to ceiling joist with

screw and washer

6. INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the

ceiling fan from falling, please install it as follows.

Step 1. Attach the provided wood screw and washers

to the ceiling joist next to the mounting bracket but do

not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to reach

the screw and washers by pulling the extra cable

through the cable clamp until the overall length is

correct, put the end of the cable back through the cable

clamp, forming a loop at the end of the cable. Tighten

the cable clamp securely. Now, put the loop in the end

of the safety cable over the wood screw securely.

NOTE: Although the safety support cable is required

for Canadian installations only. It’s a good idea to make

the attachment with any installation.

7. ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure

you have turned off the power at the main circuit panel.

NOTE: The frequencies on your receiver and wall

transmitter have been preset at the factory. Before

installing the receiver, make sure the dip switches on

the receiver and wall transmitter are set to the same

frequency. (Fig. 12)

Step 1. Insert the receiver into the ceiling mounting

bracket with the at side of the receiver facing the

ceiling. (Fig. 13)

For best performance, make sure the Black antenna,

on the end of the receiver, remains extended and not

tangled with any of the electrical wires.

Fig. 11

Fig. 13

Fig. 12

8. FINISHING THE INSTALLATION

Step 2. Motor to Receiver Electrical connections (Fig.14).

Connect the black wire from the fan to the black wire marked ”TO

MOTOR L” on the receiver.

Connect the white wire from the fan to the white wire marked ”TO

MOTOR N” from the receiver. Connect the blue wire from the fan

to the blue wire marked ”FOR LIGHT” from receiver. Secure all

the wire connections with the plastic wire nuts provided.

Step 3. Receiver to House Supply Wires Electrical Connections:

Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver. Connect the white (neutral)

wire from the ceiling to the white wire marked ”AC in N” from the

Receiver. Secure the wire connections with the plastic wire nuts

provided. (Fig. 14)

Step 4. If your outlet box has a ground wire (green or bare

copper) connect it to the fan ground wires; otherwise connect the

hanging bracket ground wire to the mounting bracket. Secure the

wire connection with a plastic nut provided. After connecting the

wires, spread them apart so that the green and white wires are

on one side of the outlet box and black and blue wires are on the

other side. Carefully tuck the wire connections up into the outlet

box. (Fig.14)

NOTE: Fan must be installed at a maximum distance of 30 feet

from the wall transmitter for optimal signal transmission between

the transmitter and the fan’s receiver unit.

Step 1. Tuck all the connections neatly into the ceiling outlet box.

Step 2. Slide the canopy up to the mounting bracket and

place one of the key hole slots over the mounting screw on the

mounting bracket. Rotate the canopy until the screw head locks

in place at the narrow section of the key hole. (Fig.15)

Step 3. Align the remaining circular hole on the canopy with

the remaining hole on the Ceiling Mounting Bracket. Insert

and tighten the mounting screw you removed earlier and the

mounting screw from step 2 above. Now, attach the canopy

cover to the mounting screw heads by inserting the screw heads

into the bottom side of the canopy cover and rotating the cover

clockwise.

NOTE: Adjust the canopy screws as necessary until the canopy

and canopy cover are snug.

Fig. 15

Fig. 14

Outlet box

Ceiling

mounting

bracket

Canopy

cover

Screw

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Outlet box

Black (hot)

Black ("AC IN L")

Receiver

White (neutral)

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

Black ("to motor L")

Blue (for light)

Black (motor)

60” Jade

Light kit pan

Fan motor assembly

Screws

White

Black

Blue

9. ATTACHING THE FAN BLADES

Step 1. Attach a blade to the fan motor assembly

by rst inserting the blade into the slot in the side

of the fan motor assembly.

Step 2. Insert a screw into the bracket. Repeat for

the two remaining screws.

Step 3. Tighten each screw securely.

Step 4. Repeat these steps for the remaining

blades.

Fan motor assembly

Screw

Blade

10. INSTALLING THE LIGHT FIXTURE

Step 1. Remove one screw from the black

bracket below the fan motor assembly. Loosen,

but do not remove the other two screws.

Step 2. Connect the blue wire exiting the bottom

of the fan motor assembly with the black wire

from the top of the light xture.

Step 3. Connect the white wire exiting the bottom

of the fan motor assembly with the white from the

top of the light xture.

Step 4. Attach the light xture to the fan motor

assembly by securing with the two screws

loosened in rst step. Push the light xture up to

engage the screw heads in the screw slots and

turn to secure. Tighten each screw rmly.

Fig. 16

Fig. 17

Non-light cap

Light kit pan

Glass Shade

Fig. 18

Fig. 19

11. INSTALLING THE SHADE

Place the glass shade into the light kit pan, aligning

the three at areas on the top ange of the shade

with the three raised dimples in the light kit pan.

Turn the shade clockwise until it stops. (Fig. 18)

NOTE: Do not overtighten when installing the

shade into the light kit. Allow the shade to cool

completely before removing.

If you install your fan without the light kit, do not

install the light kit tter assembly and follow step

below.

Place the non-light cap into the light kit pan,

aligning the three at areas on the top ange of the

non-light cap with the three raised dimples in the

light kit pan. Turn the non-light shade clockwise

until it stops. (Fig.19)

Inhaltsverzeichnis

Sprachen:

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting KLF-SOLA-34-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ridley 300027OBB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Saxon Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 inch Skye Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35153 Handbuch

Kichler Lighting

Kichler Lighting Spyn Bedienungsanleitung

Kichler Lighting

Kichler Lighting Maeve LED 52 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terna 300215 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bead Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terna 300230 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Meredith Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300395 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Szeplo II Bedienungsanleitung

Kichler Lighting

Kichler Lighting 339211APP Bedienungsanleitung

Kichler Lighting

Kichler Lighting SPYRA Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Logan Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52" Canfield Pro Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Richland II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield 300117WH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Riggs 300143 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Crescent 300325 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung