Kitsound HIVE 2 Bedienungsanleitung
USER MANUAL
JB. 5614-a / KSHIVE2 / Made in China. © KitSound™ 2017. Christchurch, Dorset, BH23 4FL, UK
All trademarks are acknowledged as the property of their respective owners.
Unless otherwise stated their use does not imply that the trademark owner is aliated
with KitSound or endorses the products herein.
HIVE 2
WIRELESS SPEAKER
kitsound.co.uk
2 3
Please read this manual carefully before use.
Box contents
• KS Hive 2
• Micro USB charge cable
• 3.5 mm aux cable
• Carry bag
• User manual
Functions
1. MFB (multi-function button)
2. LED indicator
3. Volume –/Previous track
4. Volume +/Next track
5. Power
6. Battery LED indicator
7. Aux input
8. Micro USB charge port
9. NFC 21 3 94 5 6 7 8
4 5
Battery protection mode
–If you haven’t used the speaker for 90 days, the speaker will
switch to battery protection mode automatically
–To keep the rechargeable battery in good condition, please
discharge and recharge speaker every 3 months, especially
if you are not using the speaker for long periods of time
–To cancel the battery protection mode, simply plug the Hive 2
into a charger
Getting started
–To turn the Hive 2 on, press and hold Power (5) for 5 seconds.
To turn the Hive 2 o, press and hold Power (5) for 5 seconds
whilst it is on
– The Hive 2 has an auto power o feature to save battery power
when not in use. The Hive 2 will automatically switch o if it has
not played any audio for 15 minutes
–Please ensure the rubber feet are free from dirt to prevent the
speaker moving/vibrating when playing music. If the feet need
cleaning, simply wipe them with a damp cloth
Battery LED indicator
Whilst the Hive is turned on and in use, the Battery LED indicator (6)
will light up to indicate how much power is remaining in the battery.
It will light up as the following:
• Green when the battery is at 70% charge or above
• Green and red when the battery is between 30% – 70%
• Red when the battery is below 30%
Charging the battery
The Hive 2 has a built-in rechargeable lithium battery. Make sure the
Hive 2 is switched o. Connect one end of the Micro USB charge
cable to the Micro USB charge port (8) on the Hive 2 and connect
the other end to your PC or USB mains adaptor. The battery will
start charging.
• It takes up to 4.5 hours to fully charge the battery
• Whilst charging, the battery LED indicator (6) will ash red when
below 30%, ash green and red when between 30 – 70%, and
ash green when above 70%
• When fully charged, the battery LED indicator (6) will turn solid green
6 7
Pairing a wireless device
Using NFC
With the Hive 2 turned o:
1. Press and hold Power (5) for 5 seconds
2. The LED indicator (2) will ash blue for 10 seconds, then rapidly
ash blue to indicate it is in pairing mode
3. Turn on your iOS, Android, or Windows device’s Bluetooth and
NFC ON and place it against the NFC icon (9) on the Hive 2
(you may have to remove your case for NFC to work)
4. A prompt will appear saying ‘Pair to Hive 2?’ or similar
Without NFC
With the Hive 2 turned o:
1. Press and hold Power (5) for 5 seconds
2. The LED indicator (2) will ash blue for 10 seconds, then rapidly
ash blue to indicate it is in pairing mode
3. Turn on your iOS, Android, or Windows device’s Bluetooth
ON and search for new device. Select ‘Hive 2’ from the list
of found devices
4. If asked for a passcode, enter ‘0000’ and the Hive 2 will then
be connected to your device
5. After pairing successfully, the LED indicator (2) will slowly
ash blue
6. The next time the Hive 2 is switched on, it will automatically
search for and attempt to connect to the last paired device.
Note: If your device is not connecting automatically, it’s because
it is not the last paired device. Simply delete ‘Hive 2’ from the list
of wireless devices on your device and re-pair.
5. Select ‘Pair’ and the Hive 2 will then be paired to your device
Note: ‘Bluetooth’ is a trademark of Bluetooth SIG, Inc. This product
is in no way aliated or endorsed by Bluetooth SIG Inc.
8 9
Playing audio wirelessly
1. Follow the instructions in the ‘Pairing a wireless device’ section
2. Use the controls on your device to select content
3. Audio played through the connected wireless device will now be
heard through the Hive 2
4. To play or pause the selected track, use the controls on your
device or press the MFB (1)
5. To skip track, use the controls on your device or press and hold
the Previous track (3) or the Next track (4) button
Re-pairing or pairing new devices
1. Make sure the wireless connectivity is turned o on any
previously paired devices
2. Follow the ‘Pairing a wireless device’ instructions from step 1
[...continued] Pairing a wireless device
6. The volume can be adjusted on both your device and the Hive 2.
To change the volume on the Hive 2, press (don’t hold) the
Volume – (3) or Volume + (4) button several times until you reach
the desired volume
Note: Track control functions from the buttons on the Hive 2 will
require your device to have Bluetooth prole AVRCP. Please check
your device’s manual if unsure.
Using the Aux audio input
1. With the Hive 2 turned on, insert the 3.5 mm aux cable into the
Aux input (7) on the Hive 2
2. The LED indicator (2) will turn solid red and any wireless
connection will disconnect
3. Plug the other end of the aux cable into the audio/headphone
output on an MP3 player or other audio source
4. Audio played through the connected device will now be heard
through the Hive 2
5. The volume can be adjusted on your both your device and Hive 2
Note: The play/pause and skip track functions on the Hive 2 do not
operate in aux mode.
10 11
PLEASE NOTE:
Your device will have an internal amplier and if it is playing digital
les like MP3s it will also have an integrated DAC (Digital Audio
Converter). If you turn up the volume to 100%, your device will be
sending distorted signals to the Hive 2. To avoid this and to get the
best sound quality from the speaker, we recommend that you do
not run your device any higher than 95% volume.
Also note, the Hive 2 uses a dynamic EQ which changes depending
on the volume level set on the Hive 2. We recommend you set the
volume on your device to 95% and then adjust the volume only on
the Hive 2. As you set the volume higher on the Hive 2, the bass
level will slowly decrease to prevent distortion.
Call handling
Answer a call – When a call comes through, the Hive 2 will
play a ringtone. Press the MFB (1) to answer
– During the call you can decrease/increase
the volume by pressing the Volume – (3) or
Volume + (4) button respectively
End call – During a call, press the MFB (1) to end the call
Redial – To redial the last dialled number, double press
the MFB (1)
Note: This feature is only available in wireless mode.
Care for your Hive 2
Please DON’T:
• Get the Hive 2 wet
• Drop the Hive 2 as this will invalidate your warranty
• Open up the Hive 2 as there are no user serviceable parts inside
• Expose the Hive 2 to extreme temperatures or rapid changes of
hot to cold or vice versa
Please DO:
• Clean the Hive 2 with a soft dry cloth and no detergents
12 13
Specications
Works with Bluetooth V3.0
Wireless connectivity range up to 10 m
Output 6 W x 2 (12 W total)
Output dB 1kHz @ 1m 92 dB ± 3 dB
S/N 80 dB
Aux input 3.5 mm
Battery Li-ion 2000 mAh
Frequency response 50 Hz – 20 kHz
Play time up to 12 hours
Drivers 45 mm
Charging time up to 4.5 hours
Dimensions H63.8 x W168 x D48.5 (mm)
Weight 420 g
Troubleshooting
We hope you’ve now got all the information you need to get started,
but if you’re having problems with anything, please feel free to
Hereby, Kondor Ltd declares that the radio equipment type,
KSHIVE2 Hive Wireless Speaker, is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: http://kondor.co.uk/product-documents.
14 15
We apologise for any inconvenience caused by minor inconsistencies in these
instructions, which may occur as a result of product improvement and development.
The use and operation of this speaker is beyond our control. Warranty of the Hive 2 is
limited to defects caused by faulty manufacture or defects in materials only. No warranty
whatsoever is given or implied for damage caused by the user under any circumstances.
This does not aect your statutory rights.
Please do not attempt to open this product. There are no user serviceable parts inside,
in particular if your product has an embedded, non-replaceable battery,
do not attempt to access or remove the battery as this may cause personal injury
and will damage the product.
Making any attempt to open the product or carry out repair voids any and all warranties.
Inhaltsverzeichnis
Andere Kitsound Sprecher Handbücher
Kitsound
Kitsound BOOMBAR Bedienungsanleitung
Kitsound
Kitsound UPSTAGE Bedienungsanleitung
Kitsound
Kitsound HAWAII 1.0 Bedienungsanleitung
Kitsound
Kitsound DANCEFLOOR Bedienungsanleitung
Kitsound
Kitsound SLAM 2 Bedienungsanleitung
Kitsound
Kitsound POCKETBOOM Bedienungsanleitung
Kitsound
Kitsound SOUL 2 Bedienungsanleitung
Kitsound
Kitsound GLOW Bedienungsanleitung
Kitsound
Kitsound Hive2o Bedienungsanleitung
Kitsound
Kitsound FLAIR Bedienungsanleitung
Kitsound
Kitsound POCKET HIVE Bedienungsanleitung
Kitsound
Kitsound SOUL Bedienungsanleitung
Kitsound
Kitsound Glow Stereo Bedienungsanleitung
Kitsound
Kitsound BOOGIE BUDDY Bedienungsanleitung
Kitsound
Kitsound BOOMBAR 2 Bedienungsanleitung
Kitsound
Kitsound IGNITE Bedienungsanleitung
Kitsound
Kitsound KS SLAM XL Bedienungsanleitung
Kitsound
Kitsound Sonar Bedienungsanleitung
Kitsound
Kitsound Podium Bedienungsanleitung
Kitsound
Kitsound DIGGIT XL Bedienungsanleitung
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung