Kohler Avid T97367-4-BN Bedienungsanleitung

Installation Guide

Floor-Mount Faucet

Français, page “Français-1”

Español, página “Español-1”

1389240-2-A

Tools and Materials

Important Information

CAUTION: Risk of personal injury. Do not use the bath

ﬁller as a grab bar or support bar when entering or exiting

the bath. The bath ﬁller is not designed to support weight.

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

NOTE: A minimum operating pressure of 45 psi (310 kPa) is

required for proper operation. If a pressure of less than 45 psi (310

kPa) is present, contact a plumber or choose another faucet.

Observe all local plumbing and building codes.

Shut OFF the water supply.

A drill bit is provided for installation to wood support. Use an

appropriate drill bit for other materials.

The dimensions given assume the spout and bath are mounted on

the same surface. Adjust the dimensions accordingly if the spout

and bath are mounted on different surfaces.

If this product is installed with an overﬂowing bath, the outer rim

of the bath should slightly overlap the 2x4 framing.

Installer supplied copper tubing must be 5/8″OD (1/2″

Nominal).

Carefully review this document and all appropriate roughing-in

information. Design the bath enclosure accordingly.

The appearance of your faucet may differ from the illustrations in

this guide. The instructions still apply.

Sealant Tape

Plus:

• 3/16" Masonry Bit (for concrete installation)

• Conventional Woodworking Tools and Materials

• Plumbing Tools and Materials

1389240-2-A 2 Kohler Co.

1. Prepare the Site

IMPORTANT! 2x6 lumber is NOT adequate for this application.

Bath

Finished

Floor

Subfloor

2-7/8"

(73 mm) Min

3-11/16"

(94mm) Max

Wood Support

2-3/4" (70 mm) -

3-9/16" (90 mm)

Finished

Floor

7-7/8"

(200 mm)

Min

Finished

Wall

Base

Centerline

Kohler Co. 3 1389240-2-A

Prepare the Site (cont.)

NOTICE: Adequate ﬂoor support is required. The wood support

must be a minimum of 2″(51 mm) thick by 6″(152 mm) wide. 2x6

lumber is NOT adequate for this application.

NOTE: Concrete can be used as the ﬂoor support, as long as the

faucet base will be below the ﬁnished ﬂoor level.

Plan out the bath ﬁller placement based on the dimensions above.

Cut a hole in the subﬂoor that is large enough to install the wood

support between two ﬂoor joists.

Secure a wood support 2-7/8″(73 mm) by 3-11/16″(94 mm)

below the height of the ﬁnished ﬂoor.

1389240-2-A 4 Kohler Co.

2. Spout Orientation

NOTE: Verify correct spout orientation before securing the base to

the wooden support.

NOTE: The base has a blue mark and a notch on the cold supply

side.

Orient the base with the cold supply side notch placed in the

direction shown.

If possible, dry ﬁt the faucet to the base using the screws and

washers. Orient the spout to the inside of the bath.

If your faucet is not available at this time, make sure that the base

is positioned so water from the spout will properly ﬂow into the

bath.

Mark the mounting-hole locations on the wooden support.

Mark the orientation of the base, and where the notch is

positioned on the wooden support.

Wall

Pencil

Hot

Bath

Cold

Kohler Co. 5 1389240-2-A

3. Install the Base

If attached, remove the faucet from the base.

Drill 1-1/2″(38 mm) deep holes with a 3/16″drill bit (provided)

using the marked locations as the centerpoint.

If using concrete as the ﬂoor support, use a 3/16″masonry bit

(not provided) to drill 1-1/2″(38 mm) deep holes at the marked

locations.

Realign the base to the position you marked. Make sure that the

cold supply notch is in the correct orientation.

Secure the base to the support with the provided screws and

washers.

Verify that the base is level, and tighten the screws.

Floor

Joist

Wood

Support

3/16"

Mounting

Hole

Base

Washer

Screw

1389240-2-A 6 Kohler Co.

4. Connect the Supplies

NOTE: The base has a blue mark and a notch on the cold supply

side.

Apply sealant tape on the 1/2″NPT hot and cold supply pipes,

and thread into the base.

Insert the plug(s) into the base.

Turn ON the water supply and check for leaks.

Turn OFF the water supply.

Secure the guard onto the base with the screws (provided).

Guard

Screw

Cold Supply

Base

Plug

Hot Supply

Notch

Blue Mark

Kohler Co. 7 1389240-2-A

5. Install the Finished Floor

Finish the ﬂoor leaving a 3-5/8″(92 mm) diameter hole for the

guard.

Cut the guard so it is ﬂush with the ﬁnished ﬂoor.

Guard

Finished Floor 3-5/8"

(92 mm)

Fit the finished floor

between the

Min and Max lines.

1389240-2-A 8 Kohler Co.

6. Install the Faucet

NOTICE: Keep the faucet vertical during installation to avoid

damaging the faucet O-rings.

Make sure that the water is turned OFF.

Carefully relieve the water pressure.

Remove the plug(s) from the base.

Remove the rubber protector (not shown) from the faucet.

Verify that the base is completely free of dirt and debris.

Position the faucet on the base, and insert the screws and washers

(provided) through the ﬂange.

Tighten the screws using the hex wrench provided.

Slide the escutcheon down onto the ﬂoor to cover the base.

Hex

Wrench

Escutcheon

Screw

Washer

Flange

Plug

Base

Kohler Co. 9 1389240-2-A

7. Install the Handshower

Install the handshower hose as shown.

Handshower

Holder

Hose

Diverter

Washer

1389240-2-A 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Candide 7688K-4E3 Bedienungsanleitung

Kohler

Kohler K-98835T-L Bedienungsanleitung

Kohler

Kohler K-13108 Montageanleitung

Kohler

Kohler K-2608 Montageanleitung

Kohler

Kohler K-7305 Betriebsanleitung

Kohler

Kohler K-14675 Montageanleitung

Kohler

Kohler Rapport K-1496-H2 Bedienungsanleitung

Kohler

Kohler K-1997 Montageanleitung

Kohler

Kohler K-4991X Montageanleitung

Kohler

Kohler K-1630-L Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Kohler

Kohler 10373 Bedienungsanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler Cabriole K-T14641 Montageanleitung

Kohler

Kohler Elevation Bedienungsanleitung

Kohler

Kohler K-7914 Montageanleitung

Kohler

Kohler K-2829 Bedienungsanleitung

Kohler

Kohler Symbol Rite-Temp K-T18488 Bedienungsanleitung

Kohler

Kohler K-11660 Montageanleitung

Kohler

Kohler Sterling TS27370-4G Bedienungsanleitung

Kohler

Kohler K-16109 Bedienungsanleitung

Kohler

Kohler 16366 Bedienungsanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler K-9025 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung