Kohler Finial K-20012T-CP Bedienungsanleitung

所有的资料是按最新出版的产品资料编写而成。

科勒公司保留任何时候不经通知即可改变产品特

性、包装或产品可供类型的权利。

说明书包括重要的安装、保养及清洁方面的内容，

请把这些资料交给用户阅读。

Finial Sensor Faucet

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.5GPM）

FINIAL COLD ONLY(W/O P)0.5GPM

芬尼奥台盆感应龙头 (冷热混合型/不含电源盒/0.5GPM）

FINIAL MIXER(W/O P)0.5GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.35GPM）

FINIAL COLD ONLY(W/O P)0.35GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.26GPM）

FINIAL COLD ONLY(W/O P)0.26GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.5GPM）

FINIAL COLD ONLY(W/O P)0.5GPM

芬尼奥台盆感应龙头（冷热混合型/不含电源盒/0.5GPM）

FINIAL MIXER(W/O P)0.5GPM

芬尼奥台盆感应龙头-典雅黑（单冷型不含电源盒0.5GPM）

FINIAL SENSOR FAUCET COLD ONLY(W/O P)2BZ

芬尼奥台盆感应龙头-罗曼银（单冷型不含电源盒0.5GPM）

FINIAL SENSOR FAUCET COLD ONLY(W/O P)BN

芬尼奥台盆感应龙头-玫瑰金（单冷型不含电源盒0.5GPM）

FINIAL SENSOR FAUCET COLD ONLY(W/O P)RGD

安装之前

All information is based on the latest product information

available at the time of publication, Kohler Co. reserves the

right to make changes to product characteristics, packaging,

or availability at any time without notice. Please deliver these

instructions for the consumer. They contain important

installation, maintenance and cleaning information.

BEFORE YOU BEGIN

1293596-T01-A

科勒（中国）投资有限公司

中国上海市闸北区江场三路158号邮编：200436

制造商：上海科勒电子科技有限公司

中国上海市宝山区丰翔路1955号邮编:200444

K-20012T-CP

K-20013T-CP

K-20012T-S3-CP

K-20012T-S5-CP

K-20012H-CP

K-20013H-CP

K-20012T-2BZ

K-20012T-BN

K-20012T-RGD

1293596-T01-A

维修交流龙头时，必须断开交流电源并关闭

水源。

Turn off the electrical source and shut down water

supply before servicing faucet.

1. 手伸到出水口下方感应范围

内（感应距离随面盆、周围的情

况而自动调节），水龙头出水。

手离，0.5～1秒，水龙头自动止

水。

使用说明 OPERATING INSTRUCTIONS

2. 冷热混水龙头水温调节：先

关闭热水角阀，再将冷水角阀旋

至冷水最大状态，再缓慢打开热

水角阀，以免烫伤。如冷水水压

大，打开全部热水角阀后，仍无

合适水温，请再缓慢减少冷水出

水量，直至水温使用舒适。

1. Place your hands under the faucet within the

sensor range ( the sensor range will auto-adjust

to its surroundings , the faucet should be on.)

The faucet will automatically turn off after 0.5~1

second after moving your hands away from the

sensor. The sensing distance will be adjusted

automatically per the condition of the lavatory

and surrounding environment.

Adjust the water temp for faucet with

temperature mixture: turn off hot water valve

first, and then turn on the water and adjust to full

cold, slowly turn on hot water valve to avoid

scalding. If cold water pressure is high and

unable to gain proper comfortable water temp

even hot water valve is fully open, turn down

cold water capacity slowly until water temp is

comfortable for use.

10.

11.

对于冷热混水龙头，先将连接热水的角阀关

闭，以免烫伤。

12.

修理面盆时，用黑色电工胶布粘住感应窗口。 11.

For faucet with temperature mixer, please turn off valve

before connecting to hot water to avoid scalding.

12.

Cover the sensing window with black tape when repairing

lavatories.

6. 对于交流龙头，安装时务必按照说明书的要求

正确连接导线，龙头安装完毕后才可向电源盒供

电。

7. 一个交流电源盒最多可供两个感应龙头。

8. 交流电的总电源必须有合适熔断丝加以保护。

9. 请勿使产品感应窗口靠近强紫外线或电磁场。

6. For electric connection on AC faucets, carefully follow the

installation instructions provided. Only provide to the electric

power box after the installation is conpleted.

7. Only install a maximum of two faucets to one AC/DC

transformer.

8. Ensure electrical source is fitted with a suitable fuse to

protect AC/DC transformer unit from damage.

9. Do not put the faucet near strong ultraviolet or

electromagnetic field.

安装之前（续） BEFORE YOU BEGIN(Continued)

10.

1.一定要先彻底冲洗供水管以清除管道中的杂质,

使用水源为自来水或可供饮用水。

2. 请勿将强力及冲击施于产品，以免造成故障，

引起漏水。

3. 安装、清洁龙头时，切勿损伤感应窗口表面，

以免造成故障。

NOTES:

注意事项:

1. Flush the water supply pipes thoroughly to remove debris.

Faucet is designed for tap water or potable water.

2. Handle the faucet with care to avoid damaged.

3. Do not damage the surface of sensing window when

installing or cleaning the faucet.

4. 如果是安装新的洗面盆，可将水龙头和排水组

件先安装好到面盆上。

4. For new installations, install the faucet and drain to the

lavatory before installing the lavatory.

5. 对于直流龙头，安装时注意电池的正负极不能

装反，电池盒盖要拧紧，防止电池受潮。

5. As for DC type faucets, please pay special attention to

insert direction matches battery poles. Tighten the battery

cover completely to prevent its exposure to moisture.

K-2759T-1 皓玥修边式台上盆

K-2075T-1 史瑞夫台上脸盆

K-2351T-1 希玛龙台上脸盆

K-2196T-1 斑宁登修边式台上脸盆

K-2009T-1 富丽奥修边式台上脸盆

K-2881 维克椭圆形台下脸盆

K-2883 维克圆形台下脸盆

K-2339T 梅玛台下脸盆

K-2940T 温蒂斯大尺寸台下脸盆

K-2240T 温蒂斯台下脸盆

K-2319 贝卡夫台下盆

K-2768T-1 皓玥台下盆

K-2215T-M 拉蒂纳台下脸盆

K-2751T 希玛龙台下盆

K-2336T 蒂梵诗台下脸盆

K-99184T 乔司 21"椭圆形台下盆

K-97011T 乔司16"正圆形台下盆

K-97012T 乔司16"正圆形台下盆

K-2210T 卡斯登台下脸盆

K-2211T 卡斯登台下脸盆

K-2219T 利尼亚台下脸盆

1293596-T01-A

注意：如果使用非推荐的脸盆，可能会

产生溅水在脸盆外面感应效果差等情况。

NOTE: Use of a non-recommended lavatory may result

in water spillage outside the lavatory which will cause the

poor sensing problem.

K-2759T-1 Karess Self-rimming Lavatory

K-2075T-1 Serif® Self-rimming Lavatory

K-2351T-1 Cimarron® Self-rimming Lavatory

K-2196T-1 Pennington® Self-rimming Lavatory

K-2009T-1 Folio® Self-rimming Lavatory

K-2881 Verticyl® Oval Undercounter Lavatory

K-2883 Verticyl® Round Undercounter Lavatory

K-2339T MEMOIRS® Undercounter Lavatory

K-2940T Vintage® Undercounter Lavatory

K-2240T Vintage® Undercounter Lavatory

K-2319 Bancroft® Undercounter Lavatory

K-2768T-1 Karess Undercounter Lavatory

K-2215T-M Ladena® Undercounter Lavatory

K-2751T Cimarron® Undercounter Lavatory

K-2336T DEVONSHIRE® Undercounter Lavatory

K-99184T Chalice™ Undercounter Lavatory

K-97011T Chalice™ Undercounter Lavatory

K-97012T Chalice™ Undercounter Lavatory

K-2210T CAXTON™ Undercounter Lavatory

K-2211T CAXTON™ Undercounter Lavatory

K-2219T LINIA™ Undercounter Lavatory

K-2764T-1 皓玥时尚碗盆

K-15096T 艾贝一体化盆

K-15095T 艾贝一体化盆

K-2264T 苔丝修边式台上脸盆

K-2186T-1 芬乐尔台上脸盆

K-2991-1 纽英伦修边式台上盆(长方形)单孔

K-2992-1 纽英伦修边式台上盆(椭圆形)单孔

K-2189T-1 珀特勒修边式脸盆

K-2241T-1 梅玛修边式台上脸盆

K-2220T 温蒂斯脸盆

K-2764T-1 Karess Vessel

K-15096T Urbanity™ Vanity

K-15095T Urbanity™ Vanity

K-2264T TRESHAMTM Self-rimming Lavatory

K-2186T-1 Fleur® Self-rimming Lavatory

K-2991-1 Tresham™ Self-rimming Lavatory (Rectangle）

K-2992-1 Tresham™ Self-rimming Lavatory（Oval）

K-2189T-1 Portrait® Self-rimming Lavatory

K-2241T-1 Memoirs® Self-rimming Lavatory

K-2220T Vintage® Self-rimming Lavatory

建议搭配脸盆

MATCHING LAVATORY RECOMMENDATIONS

162

Vessel rim

24484T-NA

DC Power Unit

直流电源盒

K-20013T-CP FINIAL MIXER(W/O P)0.5GPM

芬尼奥台盆感应龙头 (冷热混合型/不含电源盒/0.5GPM）

K-20013H-CP FINIAL MIXER(W/O P)0.5GPM

芬尼奥台盆感应龙头（冷热混合型/不含电源盒/0.5GPM） Whole metope

125

Drain

162 116

Vessel rim 5 6

41.2

66.5

31.75

Output: DC6V

直流电压6V

226

16305T-NA

AC/DC transformer

直流电压6V

注意: ,

安装尺寸 ROUGH-IN DIMENSIONS

Whole metope

NOTE: When installing a self-rimming lavatory

make sure the distance between the wall and the

lavatory does not exceed 10cm.

Input: AC220V

220V

Output: DC6V

10cm,

K-20012T-CP FINIAL COLD ONLY(W/O P)0.5GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.5GPM）

K-20012T-S3-CP FINIAL COLD ONLY(W/O P)0.35GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.35GPM）

K-20012T-S5-CP FINIAL COLD ONLY(W/O P)0.26GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.26GPM）

K-20012H-CP FINIAL COLD ONLY(W/O P)0.5GPM

芬尼奥台盆感应龙头（单冷型/不含电源盒/0.5GPM）

1293596-T01-A4

125

116 5 6

K-20012T-2BZ FINIAL COLD ONLY(W/O P)2BZ

芬尼奥台盆感应龙头-典雅黑（单冷型不含电源盒0.5GPM）

K-20012T-BN FINIAL COLD ONLY(W/O P)BN

芬尼奥台盆感应龙头-罗曼银（单冷型不含电源盒0.5GPM）

K-20012T-RGD FINIAL COLD ONLY(W/O P)RGD

芬尼奥台盆感应龙头-玫瑰金（单冷型不含电源盒0.5GPM）

INSTALLATION

安装步骤

如何安装水龙头

一龙头与面盆的安装固定

将龙头电控盒及线(8)和进水软管（7）穿

过橡胶垫片（2），并将橡胶垫片（2）嵌

入龙头(1)底部的盘槽中，再将电控盒及

线(8)和进水软管(7)从面盆安装孔穿过，

从台盆下方依次将垫片(3)压片(4)固定环

(5)穿过电控盒及线(8)和进水软管(7)，

穿时需先穿电控盒及线(8)再穿进水软管

(7)，将固定环按照图示方向拧在牙管

上，用十字螺丝刀将两个螺钉(6)紧固在

固定环上，由螺钉端部压紧压片(4)固定

水龙头。

注意:龙头安装时与电控盒（8）连接的

两根光纤不可弯折，否则会造出感应不灵

敏或不感应现象。

技术参数

电源：直流电源盒 4节5号碱性电池(LR06×4)

环境温度：1～55

进水温度：0.5～71

适用水压：0.05～

0.86MPa

TECHNICAL SPECIFICATION

Power: DC Power Unit 4 pieces of AA size alkaline batteries

℃

二安装阀体组件

关闭角阀（11），

对于冷热混水型的阀体组件安装是先将三

通进水软管组件的两端与角阀（11）连

接，然后把阀体组件（9）进水口处的保

护帽旋出，将阀体组件（9）进水口与三

通进水软管组件（10）连接；

对于单冷型的阀体组件安装是把阀体组件

（9）进水口处的保护帽旋出，将主阀体

组件（9）进水口与角阀（11）连接；

How to Install the Faucet

1.Secure Faucet on Lavatory

电源盒输入 220V 50/60Hz

0.5

0.5～1

AC/DC transformer Input

约1.9L/min

K-2012T-S3-xx 约1.4L/min

K-2012T-S5-xx 约1.0L/min

K-2012T/H-xx

K-2013T/H-xx

About 1.9L/min

K-2012T-S3-xx About 1.4L/min

K-2012T-S5-xx About 1.0L/min

K-2012T/H-xx

K-2013T/H-xx

1293596-T01-A

2. Install Valve Assembly

Turn valve off (11).

For mixing water valve assembly

installation, connect water inlet hose

assembly to both ends of stop valve (11),

then unscrew valve assembly (9) water inlet

protection cap, connect valve assembly (9)

inlet to Tee water inlet hose assembly (10);

for cold water faucet installation, unscrew

valve assembly (9) water inlet protection

cap, connect valve assembly (9) inlet to

valve (11);

Insert faucet control box/wire (8) and inlet

hose (7) through gasket (2), then seat

gasket (2) in the groove on the underside of

the faucet. Insert faucet control box/wire (8)

and inlet hose (7) through lavatory mounting

hole, then insert gasket (3), tab (4) retainer

(5) through control box/wire (8). Remember

insert faucet control box/wire (8) first and

then inlet hose (7), fasten retainer on stud

as shown in the directions. Last, fasten two

screws (6) on retainer, press tab (4) from the

top of screws to secure the faucet.

NOTE: Do not bend two optical fibers

connected between faucet and control box

(8), otherwise, it will cause insensitive or

non-sensing problems.

超时用水控制：超时用水1分钟，自动止水。

Overtime Flowing Control: Automatically stop flushing when

the faucet senses an object for more than 1 minute

continuously

Ambient Temperature: 1~55℃

Supply Water Temperature: 0.5~71℃

Supply Water Pressure: 0.05~0.86MPa

1293596-T01-A

三安装排水组件 Install Drain

注意：建议在连接供水时,在供水管上

连接一个临时橡皮或塑料软管，冲洗

供水管道，确保水干净，管道内无沙

石、垢物等。

NOTE: It is recommended to attach a

temporary rubber or plastic hose to the

supply hose, and then flush the hose

to remove dirt and debris.

旋下排水器盘片(12)，在其底面沿

周围涂上一圈密封油灰。把排水

本体(13)由底下插入面盆。

Unscrew the drain flange (12) and apply

plumber's putty to its underside. Insert the

drain body (13) to the lavatory from below.

把尾管(15)接上存水弯(16)，尾管需

插入存水弯25mm到55mm之间。

Connect the tailpiece(15) to the trap(16).

The tailpiece should extend 25mm to

55mm into the trap.

Thread the drain flange (12) onto the drain

body (13). Tighten the locknut (14) by

hand from below. Remove excess putty.

NOTE: Do not change the position of the

drain after the locknut(14) is tightened, is

tightened as doing so will cause damage

to the putty seal.

把排水器盘片(12)旋入排水本体

(13)。从下方用手拧紧锁紧螺母

(14)，去除多余的油灰。

注意：在锁紧螺母(14)拧紧后，不

可再调整排水本体的位置，否则将

会破坏油灰密封。

1. 取出电池盒组件，旋松螺钉

（17），按电池盒盖（18）上的正

负极标示装入4节5号电池，紧锁电

池盒盖（18）的螺钉（17）后。

注意：电池极性不能装反，新旧

电池不能混用。

2. 在合适的位置打孔，打入膨胀管，

用自攻螺钉固定电池盒。将相同颜

色接插件分别连接。

注意：接插件位置朝上。

四安装直流电源盒 4. Install DC Power Unit

1. Take out battery case assy., and

loosen the screws(17). Place 4 AA batteries

into the battery case according to negative

and positive electrode marks on the battery

case cover(18). Tighten the screws on the

battery case cover(18).

NOTE: do not mistake the battery electrodes,

and do not use the new and used batteries

together.

2. Determine the installation location of

battery case per rough-in.

Drill holes and place sheath in it. Secure the

battery case with self-tapping screws and

connect each colored connector to the

corresponding connector of the same color.

NOTE: Connectors shall face up.

Apply plumber’s

putty

涂油灰

然后拔去软管头部的保护套，将软管（7）

插入阀体出水口快速夹头中。注意主阀体

组件与墙面保持平行，与角阀连接牢固，

软管插到夹头底部，如果没有插到底易漏

水。

then remove hose protector, insert hose (7)

into valve outlet quick connector. Pay

attention to valve assembly as it must be

parallel to the wall. For a good valve

connection, insert the hose into the bottom

of connector; otherwise a leakage problem

may occur.

1293596-T01-A

安装交流电源盒

一个交流电源盒供一个感应龙头

Wire connection illustration for one to one

INSTALL AC POWER SUPPLY

(For AC-powered touchless

faucets only)

(仅限于交流感应龙头)

一个交流电源盒供两个感应龙头

Wire connection illustration for one to two

Connect to

AC Power

接交流电源

Connect to

Faucet

接感应龙头

Connect to

AC Power

接交流电源

Connect to

Faucet

接感应龙头

注意：禁止将交流AC220V接入直流DC接线端。

NOTE: Do not connect 220V AC power to a DC connector.

交流电源盒

AC Power Supply

交流电源盒

AC Power Supply

接220V交流电

Connect to AC 220V

Switch

开关 Wire Tube

穿线管

接220V交流电

Connect to AC 220V

Switch

开关

Wire.Tube

穿线管

HOW TO CHANGE TO A MIXING SENSOR

FAUCET (If customerpurchases tee inlet

assy 1284583-SP)

如何转换成混水感应龙头

(若用户另购三通进水软管

组件1284583-SP)

1. ( )

0.5mm

0.3mm

1. AC power unit (sticker on the back) should be installed in a

dry place away from water. Customer should prepare wire

tube and wire according to their requirement. Wire tube should

be mounted into the wall. Suggested wire: AC connection

wire adopts wire with protecting layer or sleeve and the section

should be ≥ 0.5mm . The section of DC connection wire

should be ≥ 0.3mm . The connection pattern must follow the

illustrations above.

2.After wire layout finished, check and repair if needed.

Then connect AC connector to AC connector within FPC

pipe, DC connect or (black-orange) on electrical box to

faucet power cord connector (wire from valve

box). Finally turn on AC power source.Faucet will commence

auto-sense mode which will take 2minutes. The faucet will

not work during this period.

( )

AC 2分钟

1293596-T01-A

≤400

用户自备角阀G1/2外螺纹

Please prepare external

thread angle valve G1/2

三通进水软管组件

Tee, Inlet Assy.

1. 感应指示灯的各种闪烁情况

感应指示灯是使用者了解感应龙头有效、唯一

的途径。所以明白了感应指示灯闪烁所代表的

含义，可以正确使用感应龙头，

IMPORTANT CONSUMER INFORMATION

清理说明

适用于所有加工处理过的表面，以中性肥皂水清

洗镀层表面，再以干净的软布彻底擦干整个表

面。许多清洁剂，比如氨水，去污粉及洁厕灵

等，会对电镀表面造成伤害，切忌使用。

有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙

头及其配件上。

用户须知

安装结果检查

检查并确保所有衔接处都已拧紧，打开排水系统

和主要供水源，检查并修理有漏水的接口。

INSTALLATION CHECKLIST

Check and ensure that all connections are tight. Open the

drain. Turn on main water supply and check for leaks.

Repair leakage when necessary.

CLEANING INSTRUCTIONS

Applicable for all finishes: clean the finish with a mild soap.

Wipe entire surface completely dry with a clean soft cloth.

Most cleaners may contain chemicals, such as ammonia,

chlorine, toilet cleaner etc. which could adversely affect the

finish and are not recommended for cleaning. Do not use

abrasive cleaners or solvents on Kohler faucets and

fittings.

1. Light indicator Key

The indicator is the only and effective way to learn the

faucets working conditions. So the users can use the

sensor faucet correctly with knowing the meaning of the

sensor indicator's flashing.

1293596-T01-A

如何转换成恒温阀感应龙头

(若用户另购

恒温阀16294T-3-CP,

具体安装详见其说明书

)

墙面

Wall

接感应龙头

Connect to Sensor Faucet

注意：软管、三通、角阀请用户自备。

墙面

Wall

NOTE: User shall prepare hoses, tees and stop valves by

him/herself.

CHANGE TO THERMOSTATIC

SENSOR FAUCET (If user chooses to

order Thermostatic Valve K-16294T-3-

CP, refer to its installation instructions

for details.)

最小50mm

Min 50mm

恒温阀

Thermostatic valve

角阀

Stop Valve

角阀

Stop Valve

三通

Tee

出水口

Outlet

三通

Tee

三通

Tee

进热水

hot

进冷水

cold

用户须知（续） IMPORTANT CONSUMER INFORMATION

(Continued)

超时出水控制

连续在感应状态下使用约一分钟，龙头自动止水。

自动止水后，手或物体离开感应范围后，再次进

入感应范围内，龙头正常工作，否则无反应。

指示灯

Indicator Light

When the faucet flows continuously for 1 minute, the

faucet will automatically stop.Objects must be removed

from the sensing range. Then the water will flow when

objects re-enter into the sensing range again. Otherwise,

the faucet will not work.

2. Timeout setting

As shown:

(1) Quick flashing means the faucet is in the

period of adjusting sensing distance after power

on for 2 minutes. During these 2 minutes, please

do not disturb auto adjustment or place objects

within the sensing range.

(2) The indicator flashes every 6 seconds (DC

type) indicates that the unit is out of battery and

has stopped working. Replease batteries.

(3) The indicator flashes every 2s: as for DC type

faucets, this indicates the unit is out of battery and

ceases working. Please replace batteries. For AC

faucet, it indicates two possibilities: one is that the

unit is out of battery; or poor DC terminal contact

under normal AC power supply.

(4) Under normal condition, the water will flow and

the indicator will flash once when objects are

detected. (The indicator does not flash when

faucet stops flowing.)

如图示:

(1) 快速闪烁，代表感应龙头正处于通电后

的两分钟自动调节阶段。期间，安装者、使

用者不得干扰其自动调节，感应范围内不要

放置物体。

(2) 间隔6秒钟闪烁一次（直流版本），表

示电池即将使用完，请更换电池。

(3)

间隔2秒钟闪烁一次：若直流感应龙头,

代表龙头电池耗尽，已停止工作，等待使

用者更换电池;若交流感应龙头，表示为两

种情况：一种为刚刚停电；另一种为在交

流供电正常的情况下，则电源盒直流接线

端接触不良。

(4) 在正常工作情况下，当有物体被感应

时，龙头出水，感应指示灯闪烁一次.(龙头

关闭，感应指示灯不闪烁）

1293596-T01-A

3.清洗过滤系统

该感应龙头的阀体组件内已包含了优良的过滤装

置。如管内杂质过多或水质较差，长期使用会引

起出水情况不良。请按以下步骤清洗过滤装置：

1. 关闭角阀。

3. Clean the Filtration System

The faucet includes connector assembly with high quality

filtration system. Excessive debris and water of bad

quality can cause block in the pipe, thus reducing water

flow. Please clean th filtration system as following:

1. Close the stop valve.

2.将主阀体组件取下，拿出滤网

(19)(20)，用水冲洗完毕后，重新

装入。

注意：在清洗完滤网后，不要遗失

平垫。

2. Remove the valve assembly and take out the

filter(19)(20)for cleaning, then re-install it.

NOTE:

Ensure that the filter washer is installed after the

filter is cleaned.

4.自动清洗存水功能 4.

When the faucet is no used for a long period of time, it will

automatically flush to discharge the stagnant water inside

the faucet every 24hrs.

感应龙头长期处于不使用状态时，

每间隔24小时自动冲水一段时间排

出龙头内的存水。

Self-Cleaning the stagnant water

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-2363X Montageanleitung

Kohler

Kohler K-10268 Bedienungsanleitung

Kohler

Kohler 7098M Bedienungsanleitung

Kohler

Kohler Deerfield 5815W Bedienungsanleitung

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler K-3145 Montageanleitung

Kohler

Kohler K-15261 Montageanleitung

Kohler

Kohler K-5814 Bedienungsanleitung

Kohler

Kohler Family Care 2.0 K-701646T-FM-SHP Bedienungsanleitung

Kohler

Kohler 1071003-2-B Bedienungsanleitung

Kohler

Kohler ENGLEFIELD CORNER CONTOUR PLUS Bedienungsanleitung

Kohler

Kohler Margaux K-16230-4 Bedienungsanleitung

Kohler

Kohler K-10430 Montageanleitung

Kohler

Kohler K-77963-8A-BL Bedienungsanleitung

Kohler

Kohler Centerset K-15241 Montageanleitung

Kohler

Kohler K-1997 Montageanleitung

Kohler

Kohler ESCALE Bedienungsanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler MEMOIRS Series Bedienungsanleitung

Kohler

Kohler K-169 Bedienungsanleitung

Kohler

Kohler K-9295 Montageanleitung

Kohler

Kohler Fluence K-702221-6L Bedienungsanleitung

Kohler

Kohler K-T72770 Montageanleitung

Kohler

Kohler K-205 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung