Kohler Family Care 2.0 K-701646T-FM-SHP Bedienungsanleitung

-1-

BEFORE YOU BEGIN 安装之前

ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH

DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437

中山科勒卫浴有限公司广东省中山市中山火炬开发区兴业路 13-1 号邮编：528437

• 说明书中所有的资料是按最新出版的产品资料编写而成。科

勒中国有限公司保留任何时候无须通知即可改变产品特性、

包装或产品可供类型的权利。

• 说明书包括重要的安装、清洁及保养方面的内容，请把这些

资料交给用户阅读，保管。

• 确保在安装淋浴房之前已经完整正确地安装了浴室和完工

墙面材料。淋浴区墙地面应做防水处理，并不得布置有电器

开关、插座。确保地面排水通畅。

• 在进行淋浴房安装之前，请拿出、排列并确认所有的零部件。

请参考第 2 页上所示的分解图。

• 对尺寸与本标准产品不同的定制淋浴房，参照本说明书进行

安装。

• 本产品符合 QB 2584-2007。

• All information is based on the latest product information

available at the time of publication. Kohler China Ltd.

reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

• These instructions contain important care, cleaning, and

warranty information-please leave these instructions for

the consumer.

• Make sure that the bath and the finished wall material are

completely and correctly installed prior to installing your

shower door. Prepare waterproof layer to wall and floor of

the showering area. It is not allowed for any presence of

electric switches and sockets. Make sure the floor drain

runs smoothly.

• Before starting the door installation, lay out and identify all

the parts. Use the exploded view illustrated on page 2 for

reference.

• For the installation method of customized shower with

different dimensions, please refer to this instructions.

• The product complies with QB 2584-2007.

警告：可能有人员伤害或者产品损坏的危险。

钢化玻璃不能进行切割，钻孔或硬物敲击。搬移或安装过

程中，小心确保玻璃边、角部位不受撞击，以防爆裂伤人。

建议：将本产品安装在科勒淋浴盆或挡水条上（需另行购买）。

如自备挡水条，建议顶面宽度尺寸大于 80mm。

重要事项：淋浴房需要安装在平坦垂直的墙面上。墙面的垂直度推

荐在正负 3mm/m 以内。如果超出此范围，科勒公司将不保证淋浴

房的完美使用。

CAUTION: Risk of injury or product damage.

Tempered glass cannot be cut, drilled or knocked by

hard object. Make sure corner area of the glass

refraining from knocking so as to cause personal injury

due to broken glass.

ATTENTION: Please install this door on Kohler receptors or

curbs(Not included). If the curb is not Kohler-branded, please

note its top width should be more than 80mm.

IMPORTANT: The shower door requires a flat vertical

finished wall. The squareness of the wall is recommended no

more than 3 mm/m. KOHLER Company won't take

responsibility of the installation quality.

24hrs

ROUGHING-IN 尺寸图

Unit: mm

单位：毫米

Do not use the enclosure for at least 24 hours.

安装后 24 小时内请勿使用淋浴房。

FAMILY CARE 2.0

INSTALLATION INSTRUCTIONS

安装说明书

L SHAPE, 1D2P, 10mm FM

开门L型，两固一活，10mm贴膜玻璃

K-701646T-FM-SHP

L SHAPE,1D2P, 8mm FM

开门L型，两固一活，8mm贴膜玻璃

K-701650T-FM-SHP

SKU B H

900-1450

250-1100 1850-2200

K-701646T

K-701650T

1415130-T01-A

-2-

Top Hinge Component 上铰链组件

Hinge Shaft 转轴

Hinge Sleeve 轴套

Decorated Cover of Inner Fixed Block 固玻内固定块装饰盖

Inner Fixed Block 内固定块

Fixed Block Washer 固定块垫片

External Fixed Block 外固定块

Wall Top Cover 墙材上端盖

Decorated Cover 下固定座装饰盖

Top Frame 上横梁

Bottom Fixed Seat 下固定座

Top Fixed Seat 上固定座

Soft Handle 软把手

Magnetic Strip Fixed Frame 磁条固定边框

Side Frame of Fixed Glass 固玻边框

Door Glass Side Frame 门玻转角边框

Side Frame of Fixed Glass 固玻边框

Wall Frame 固玻墙材

ST3.5X25 Self Drilling Screw

ST3.5X25自攻螺钉

L Shape Corner Frame Top Cover

L型转角铝材上端盖

Top Hinge Component

上铰链组件

ST3.5X12 Self Drilling Screw

ST3.5X12 盘头自攻螺钉

Top Frame

上横梁

Side Panel Wall

Frame Top Cover

侧固玻墙材上端盖

Side Panel Wall

Frame

侧固玻上墙材

Side Panel Wall Frame

侧固玻上墙材

Decorated Cover for

Side Panel

L型侧固玻墙材装饰盖

Side Panel

侧固玻

Bubble Seal Strip

10mm 密封气泡胶条

8mm 密封气泡胶条

Decorated Strip

装饰胶条

ST3.5X8 Screw

ST3.5X8 十字盘头螺钉

M4X10 Mechanical Screw

M4X10 半圆头机制螺丝

Door Glass Side Frame

门玻转角边框

Bottom Fixed Seat

下固定座

Decorated Cover

下固定座装饰盖

Grub Screw

内六角紧固螺钉

Hinge Sleeve

轴套

Hinge Shaft

转轴

Sealing Strip

门底挡水胶条

Decorated Cover of Inner Fixed Block

固玻内固定块装饰盖

M4X25 Screw

M4X25 十字槽沉头螺钉

Inner Fixed Block

内固定块

Fixed Block Washer

固定块垫片

Bottom Strip of Fixed Glass

固玻下胶条

External Fixed Block

外固定块

Front Fixed Panel

固玻

Wall Top Cover

墙材端盖

Side Frame Top Cover

边框上端盖

ST3.5X40 Cross Slot

Pan Head Screw

ST3.5X40自攻螺钉

Side Fixed Strip

单边固定胶条

Fixed Glass Wall Frame

固玻墙材

Magnetic Strip Fixed

Frame

磁条固定边框

Side Frame of Fixed Glass

固玻边框

Soft Handle

软把手

X16

Decorated Strip 装饰胶条

Screw GB/T 845 ST3.5X25 十字圆头不锈钢自攻螺丝ST3.5X25

M4X10 Cross Slot Mechanical Screw

M4X10 半圆头机制螺丝

M5X6 Grub Screw

M5X6 内六角紧固螺钉(预装在下固定座装饰盖）

Hollow Wall Anchor Nylon 膨胀套

Screw Key 2.5mm 内六角扳手

Screw GB/T 845 ST3.5X25 十字圆头不锈钢自攻螺丝ST3.5X25

Side Panel Wall Frame Top Cover 侧固玻墙材上端盖

Screw GB/T 845 ST3.5X12 十字圆头不锈钢自攻螺丝ST3.5X12

Pan Screw ST3.5X40 圆头螺丝ST3.5X40

Sealing Strip 门底挡水胶条

Bottom Strip of Fixed Glass 固玻下胶条

Side Fixed Strip 单边固定胶条

Seal Strip 密封胶条

L Shape Corner Frame Top Cover L型转角铝材上端盖

Side Frame Top Cover 边框上端盖

M4X25 Countersunk Head Screw M4X25 十字槽沉头螺钉

1415130-T01-A

-3-

INSTALLATION 安装

STEP

1. The installation area shall be 20cm higher than the door glass.

2.When a floor drain is present, the floor flatness shall not exceed 1mm per meter.

3.The seal, if any, shall be adjusted to a horizontal state.

1.淋浴房安装区域的空间高度，要比淋浴房高20厘米才能正常安装。

2.对于配地漏使用的淋浴房地板平面度要求，每米长度不能超过1mm，地漏和门玻在同一侧。

3.对于配挡水条安装的淋浴房，要求将挡水条调至水平状态。

1.When a seal is installed, place the frame assembly inside the seal 10mm from its outer

edge. Mark the drilling positions by reference to the holes in jambs of the door glass and

the side panel glass.

2.When no seal is installed, position the jambs of the door glass along the floor drain edge

and position the jambs of the side panel inside the door glass 10mm from the outer edge.

Mark the drilling positions.

3.Drill holes into the wall at the marked positions. Install the expansion fastener.

1.带挡水条的淋浴房，参照淋浴房挡水条边沿从外往里偏移10mm，参照正面和侧面上墙材孔

位标记钻孔位置。

2.对于不带挡水条的淋浴房，正面墙材靠着地漏边沿定位，侧面墙材按照淋浴房下单宽度往里

偏移10mm，标记打孔位置。

3.参考固定孔标记位置钻孔，安装膨胀套。

1.Fix the wall jamb of the side panel glass (the wall jamb of the door glass is not fixed now).

2.Insert the side panel glass into the wall jamb.

1.先固定侧固玻上墙材（注意正面墙材先不固定）。

2.将侧固玻装入侧固玻墙材。

1.Fix the frame and the jamb at the wall side onto the wall.

2.Adjust the adjusting screws on the side frames and jambs of the door glass so that the

center post is pressed against the side frame of the side panel glass.

3.Fix the center post and the side frame of the side panel glass together using screws

(ST3.5x8).

1.将正面靠墙侧边框和墙材与墙壁固定。

2.调整正面边框墙材上的调节螺钉，使中立柱和侧固玻边框贴合。

3.将正面中立柱和侧固玻边框用螺钉(ST3.5X8)固定。

1.Drill a Φ3.0mm bottom hole by reference to the hole in the side jamb.

2.Fix the side jamb and the vertical frame together using screws (ST3.5x12). Then

assemble the decorated cover onto the jamb.

1.参照侧墙材上的孔配钻直径3.0mm的底孔。

2.用螺钉(ST3.5X12)将侧固玻墙材和固玻竖材锁定，然后组装侧固玻墙材装饰盖。

0mm

IMPORTANT:

Tray MUST be level

along front edge.

重要：

底盘必须水平。

The wall jamb

must be kept

vertical.

上墙材必须垂直。

0mm

The wall jamb

must be kept

vertical.

上墙材必须垂

直。

1.Fix the bottom fixture onto the door glass frame.

2.Assemble the top frame and the left and right frames (note the installation position of

ST3.5X25 screw).

3.Insert the jamb at the other side into the frame (pass the adjusting screws through

the gourd holes in the frames and slide the jambs downward to insert them into the

frames); Adjust the adjusting screws to minimize the clearance between the wall

jambs and the frames.

1.将下固定座固定在门玻边框上（参考下图）。

2.组装上横梁和左右边框（注意ST3.5X25螺钉的安装位置）。

3.将一侧墙材扣入边框（墙材上的调节螺钉穿过竖材上的葫芦孔，往下滑动扣入竖材）；

调整边框上的调节螺钉，将墙材和竖材的距离调到最小。

ST3.5X25 screw must be installed where

the arrow points. A longer screw will

interfere with the top hinge assembly.

ST3.5X25螺钉必须安装在箭头所指位置,

用长的螺钉会和上铰链组件干涉。

1.Fix the bottom fixture onto the

door glass frame.

1.将下固定座固定在门玻边框上。

10mm from the

outer edge

距边10mm

10mm from the

outer edge

距边10mm

10mm from the

outer edge

距边10mm

6mm

1415130-T01-A

-4-

INSTALLATION 安装

STEP

1.Assemble the decorated cover, hinge sleeve and hinge shaft together. Insert the

assembly into the bottom hinge. Then move the door glass to insert the decorated cover

into the bottom fixture.

2.Hold the door glass upright. Insert the limiting hinge assembly into the top hinge from the

top frame. When the door glass hangs down due to gravity, pre-tighten the limiting hinge

assembly with a screw.

1.将下固定座装饰盖、轴套、轴安装在一起，套入门玻下铰链，然后移动门玻将下固定座装饰盖

套入下固定座。

2.扶正门玻，将限位铰链组件，从上横梁插入门玻上铰链，门玻自然下垂，用螺钉预锁紧限位铰

链组件。

1.Install the handle. Install decorated seals onto the top frame, vertical frames and corner

frame.

2.Install the waterproof seal at the door glass side. Properly adjust the door glass. Tighten

the limiting hinge assembly and the decorated cover.

3.Install the waterproof seal at bottom of the door glass.

1.安装门把手。安装上横梁、竖材、转角边框上的装饰胶条。

2.安装门玻侧挡水胶条，调整好门玻的位置，锁紧限位铰链组件,锁紧下固定座装饰盖。

3.安装门玻下挡水胶条。

1.Install the seal at bottom of the panel glass. Insert the panel glass into the vertical frame.

2.Install the seal on the top and side of the panel glass.

3.Install the bottom bumper block of the panel glass.

1.安装固玻底部胶条，将固玻装入竖材。

2.安装固玻顶部和侧边紧固胶条。

3.安装固玻底部定位件。

1.Apply sealant onto both sides of the left and right jambs and also onto the edges of the

bottom fixture.

2.If a seal is installed, apply sealant onto its bottom edges.

1.墙材两侧与底部固定座边沿打胶固定。

2.带挡水条淋浴房，在挡水条底部边沿打胶固定。

1.Install the end caps onto the top of the side panel glass jamb, corner jamb and vertical

frame.

2.Install decorated seals onto the top frame, vertical frames and corner frame.

1.安装侧固玻墙材、转角墙材和竖材顶部端盖。

2.安装上横梁、竖材、转角边框上的装饰胶条。

Dieses Handbuch passt für folgende Modelle

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10586 Montageanleitung

Kohler

Kohler K-7653 Bedienungsanleitung

Kohler

Kohler Margaux K-16230-4 Bedienungsanleitung

Kohler

Kohler K-170 Montageanleitung

Kohler

Kohler TEA-FOR-TWO K-856-H2 Bedienungsanleitung

Kohler

Kohler AIRFOIL 37271X-7 Bedienungsanleitung

Kohler

Kohler K-78172-BN Bedienungsanleitung

Kohler

Kohler K-7779 Bedienungsanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler K-106 Montageanleitung

Kohler

Kohler K-20099T-Y Bedienungsanleitung

Kohler

Kohler 31138T-4 Bedienungsanleitung

Kohler

Kohler 77984T-4MU Bedienungsanleitung

Kohler

Kohler K-10430 Montageanleitung

Kohler

Kohler K-669 Montageanleitung

Kohler

Kohler K-15251 Montageanleitung

Kohler

Kohler KELSTON K-2382 Kurzanleitung

Kohler

Kohler K-10217 Bedienungsanleitung

Kohler

Kohler K-10958 Bedienungsanleitung

Kohler

Kohler STATEMENT K-26325T-CP Bedienungsanleitung

Kohler

Kohler Symbol 18471-4FP Bedienungsanleitung

Kohler

Kohler REGATTA drop in 11303A-GAB-0 Bedienungsanleitung

Kohler

Kohler COUTURE WATERGUARD Bedienungsanleitung

Kohler

Kohler Sterling 442007-U Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung