Kohler K-12183 Bedienungsanleitung

Installation Guide

Single-Control Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-12183

1011034-2-F

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

If possible, install this faucet to the lavatory before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable Wrench Plumbers Putty Sealant Tape

1011034-2-F 2 Kohler Co.

1. Install the Faucet

Apply plumbers putty or other sealant to the underside of the

escutcheon according to the manufacturer’s instructions.

Feed the faucet supply inlets through the faucet hole of the

lavatory, then position the faucet. Slide the bracket and washer

over the stud and tighten the nut to secure.

Apply

Plumbers

Putty

Supply Inlet

Stud

Bracket

Nut

Washer

Lavatory

Escutcheon

Kohler Co. 3 1011034-2-F

2. Install the Drain

If present, remove the protective plastic cap from the drain and

discard.

Remove the nut, washer, and gasket from the drain body.

Apply a bead of plumbers putty or other sealant around the

underside of the ﬂange according to the sealant manufacturer’s

instructions.

For drains with metal stoppers: Close the drain and rotate the

drain body until the logo is positioned horizontally.

Insert the drain into the drain hole and press into place.

Slide the gasket (tapered side up) onto the drain body.

Slide the washer over the threads on the drain body.

Thread the nut up the drain body until snug against the

underside of the lavatory. Use care not to rotate the drain while

tightening the nut.

Using a wrench, tighten the nut.

Remove any excess putty or sealant.

Connect the P-trap to the drain body.

Washer

Flange

Drain Body

Nut

Tapered Gasket

Thick Tapered Gasket

(for thin-walled vessel style

lavatory installations)

1011034-2-F 4 Kohler Co.

3. Connect the Supplies

CAUTION: Risk of restricted water ﬂow and product

damage. Use extreme care when bending the supplies to

avoid kinking.

CAUTION: Risk of product damage. Do not overtighten the

connections.

If the lavatory is not installed, install it at this time. Follow the

lavatory manufacturer’s instructions.

For Mexico only installations: Install the adapter.

Connect the supply tubes to the faucet supplies and supply stops.

(Left is hot - right is cold.)

Tighten the connections with an adjustable wrench.

Supply Stop

Supply Inlet

Adapter

(Mexico only)

Kohler Co. 5 1011034-2-F

4. Installation Checkout

Connect the tailpiece and P-trap.

Make sure all connections are tight.

Remove the aerator by turning it counterclockwise.

Turn on the main water supply and check for leaks. Make any

adjustments as needed.

Turn the faucet handle to the cold side and open to the ″ON″

position. Run cold water through spout for about a minute to

remove any debris.

With water still running, rotate the faucet handle to the ″HOT″

side. Continue running water through the spout for about one

minute and then turn off.

Rinse any debris from the aerator and reinstall.

Aerator

1011034-2-F 6 Kohler Co.

5. Optional Temperature Limiting Adjustment

NOTE: Prior to adjustment, make sure the handle is in the

maximum hot position.

Remove the cap, handle and bonnet.

Turn on the water to the maximum hot water temperature by

pushing the valve stem up, and turning it fully clockwise.

Use a pencil or marker to mark the current position of the

temperature stop tab (top edge) on the mounting nut. Lift both

the indexer and the top disc just enough to clear the splines and

to allow rotation.

NOTE: Each indexer notch is an average 9.5°F (5.3°C) change in

temperature.

Turn the indexer, top disc, and valve stem counterclockwise until

you achieve the desired temperature.

Reinstall the indexer and top disc to the valve. Make sure the top

disc is snapped fully into the indexer.

Turn off the water, and reinstall the bonnet, handle and cap.

Mounting

Nut

Top Disc

Splines

Stop Tab

Bonnet

Handle

Screw

Cap

Valve Stem

Kohler Co. 7 1011034-2-F

Guide d’installation

Robinet de lavabo mono-contrôle

Outils et matériels

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Si possible, installer le robinet au lavabo avant d’installer ce

dernier.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Clé à molette Ruban

d'étanchéité

pour filets

Mastic de

plombier

Kohler Co. Français-1 1011034-2-F

1. Installer le robinet

Appliquer du mastic de plombier ou un produit d’étanchéité

semblable au-dessous de l’applique selon les instructions du

fabricant.

Alimenter les entrées d’alimentation du robinet dans l’oriﬁce du

robinet du lavabo, puis positionner proprement le robinet. Glisser

le support et la rondelle sur le montant et bien visser l’écrou pour

sécuriser.

Appliquer

du mastic de

plomberie

Entrée

d'alimentation

Montant

Support

Écrou

Rondelle

Lavabo

Applique

Kohler Co. Français-2 1011034-2-F

2. Installer le drain

Si présent, retirer le capuchon de protection en plastique du drain

et jeter.

Retirer l’écrou, la rondelle et le joint d’étanchéité du corps du

drain.

Appliquer du mastic d’étanchéité ou un produit semblable sur le

dessous de la bride selon les instructions du fabricant.

Pour des drains avec arrêts métalliques: Fermer le drain et

pivoter le corps de celui-ci jusqu’à ce que le logo soit horizontal.

Insérer le drain dans son oriﬁce et presser pour mettre en place.

Glisser le joint (côté biseauté vers le haut) sur le corps du drain.

Glisser la rondelle sur les ﬁletages du corps du drain.

Visser l’écrou sur le corps du drain jusqu’à ce qu’il soit contre la

base du lavabo. Faire attention de ne pas pivoter le drain en

serrant l’écrou.

Utiliser une clé pour serrer l’écrou.

Retirer tout excédent de mastic de plombier ou de joint

d’étanchéité.

Connecter le siphon en P au corps du drain.

Bride

Joint biseauté

Rondelle Écrou

Corps du drain

Joint biseauté épais

(pour installations de

lavabo avec vasque

à parois fines)

1011034-2-F Français-3 Kohler Co.

Andere Handbücher für K-12183

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-8593 Montageanleitung

Kohler

Kohler K-1243 Bedienungsanleitung

Kohler

Kohler 1108711 Handbuch

Kohler

Kohler K-349 Montageanleitung

Kohler

Kohler Elevation Bedienungsanleitung

Kohler

Kohler Symbol 18471-4FP Bedienungsanleitung

Kohler

Kohler Escale 19046W Bedienungsanleitung

Kohler

Kohler K-17230T-DR Bedienungsanleitung

Kohler

Kohler Memoirs K-T448 Montageanleitung

Kohler

Kohler K-368 Bedienungsanleitung

Kohler

Kohler ALEO Bedienungsanleitung

Kohler

Kohler K-15003 Bedienungsanleitung

Kohler

Kohler K-73078 Montageanleitung

Kohler

Kohler Cyan K-705788 Bedienungsanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler K-393 Bedienungsanleitung

Kohler

Kohler K-101 Bedienungsanleitung

Kohler

Kohler PURIST UPGRADE K-99168T Bedienungsanleitung

Kohler

Kohler K-10577 Montageanleitung

Kohler

Kohler K-10272 Montageanleitung

Kohler

Kohler K-6331 Bedienungsanleitung

Kohler

Kohler K-9110 Montageanleitung

Kohler

Kohler K-7914 Montageanleitung

Kohler

Kohler HiRise K-7337 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung