Kohler K-15003 Bedienungsanleitung

Installation Guide

Bath-Mount Faucet

with Handshower

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-15003

113781-2-BB

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Provide an access panel for all installations.

Use 5/8″nominal tubing (3/4″O.D.) from the supply to the valve

inlets.

Install water hammer arresters in the supply line.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

• Support blocks

or straps

Plus:

Adjustable

Wrench

Tape

Measure 3/32" Hex

Wrench Snap Ring

Pliers

Solder

Propane

Torch

Drill and

Hole Bit Strap

Wrench

113781-2-BB 2 Kohler Co.

1. Component Layout

Verify the location of the components, and the orientation of all

ports.

Decide in advance on the location and orientation of the diverter.

The location of the shower, and the handshower, as well as the

direction in which the inlets/outlets point, will affect the piping

and connectors needed.

Allow clearance for valve outlets, handles, bath spout, and

handshower hoses.

Layout

Kohler Co. 3 113781-2-BB

2. Install the Diverter

Unthread and remove both elbow assemblies from the diverter.

Set aside the elbow assemblies.

Slide the washer over the diverter body.

Insert the washer up into the groove on the underside of housing.

Insert the diverter body into the mounting hole.

Rotate the diverter so the hose guide faces toward the front.

From the underside of the diverter, thread one mounting stud

into each mounting stud hole. Securely tighten.

Position the bracket onto the mounting studs and diverter.

While holding the bracket in place, thread a nut onto each

mounting stud.

Securely tighten the nuts until the bracket and diverter are snug

against the underside of the bath or ﬁnished deck.

Thread the three-way elbow assembly back into the lower

diverter port. The lower diverter port is marked by an arrow

pointing in.

Thread the elbow assembly back into the upper diverter port. The

upper diverter port is marked by an arrow pointing out.

Elbow

Assembly

3-Way Elbow

Assembly

Washer

Hose Guide

Input Port Mounting

Stud

Nut Bracket

113781-2-BB 4 Kohler Co.

3. Install the Handle Valve

Thread one mounting nut with the ﬂange side up, down each

″Cold″and ″Hot″handle valve.

Slide one ﬁber washer and one rubber washer down each ″Cold″

and ″Hot″handle valve and onto the mounting nut.

Insert one washer up into the groove on the underside of the

escutcheon.

NOTE: Handle valves that are marked ″Cold″must always be

installed into the mounting hole on the right as viewed from the

front of the bath.

From the underside of the bath, insert one of the handle valves

up into the selected mounting holes.

From the top of the bath, thread one escutcheon down each

″Cold″and ″Hot″handle valve until only one thread is exposed

above the escutcheon.

Thread the mounting nut up to the underside of the deck/rim to

secure the valve in place.

Repeat process for the second valve.

Slide one bonnet into the escutcheon and thread onto each ″Cold″

and ″Hot″handle valve.

Valve Body

Mounting Nut

Fiber Washer

Rubber Washer

Valve

Body

Outlet

Bonnet

Washer

Escutcheon

Valve Body

Flange Nut

Kohler Co. 5 113781-2-BB

4. Install the Handles

NOTE: Handles that are marked ″Cold″with a blue tape must

always be installed onto the right handle valve as viewed from the

front of the bath.

Insert a screwdriver into the slots under each ″Cold″and ″Hot’

handle cap.

Pry the handle cap until it is removed from the handle. Save for

later use.

Removed one handle screw and one lockwasher from each ″Cold″

and ″Hot″handle. Save for later use.

Loosely press one handle onto each ″Cold″and ″Hot″valve stem.

Check for proper alignment.

To adjust the alignment, go to the underside of the bath and

loosen the mounting nut. Rotate the handle valve until the proper

alignment is achieved. Securely tighten the mounting nut.

After adjustment, ﬁrmly press one handle onto each ″Cold″and

″Hot″valve stem until the stem and handle splines are engaged.

Insert one lockwasher into the screw hole of each ″Cold″and

″Hot″handle. Secure with a screw.

Firmly press one handle cap back into the top of each ″Cold″and

″Hot″handle.

Cap

Handle

Slot

Stem

Screw

Lockwasher

Valve Body Flange Nut

Slot

Handle

Copper Tubing

5/8" Nominal

(3/4" OD)

Valve Body

Inlet

113781-2-BB 6 Kohler Co.

5. Install the Spout

Insert the rubber washer up into the groove on the underside of

the spout.

From the top of the bath, insert the spout shank through the

mounting hole.

From the underside of the bath, slide one rubber washer, one

brass washer, and one ﬂange nut up onto the spout shank.

Securely tighten the ﬂange nut. Do not overtighten.

Slide one O-ring down the spout end of the adapter.

Thread the adapter up onto the spout shank until tight.

Rubber

Washer

Rubber

Washer

Spout

Shank

Flange

Nut

Brass

Washer

Spout

Shank

O-Ring

Adapter

Kohler Co. 7 113781-2-BB

6. Install the Handshower

From the top of the bath, insert the narrow end of the ﬂexible

hose into the hose guide and through the mounting hole.

Slide one ﬁber washer up onto the threads of the handshower

holder.

Thread the handshower holder into the ﬂexible hose.

Slide one screen washer onto the threads of the handshower.

Thread the handshower into the handshower holder.

From the underside of the bath, thread the ﬂexible hose onto the

special hose adapter.

Thread the special hose adapter onto the connector end of the

high pressure hose.

Insert one ﬁber washer onto the threads of the output port of the

diverter.

Thread the high pressure hose onto the output port of the

diverter.

Handshower

Handle

High Pressure

Hose

Handshower

Holder

Fiber

Washer Fiber

Washer

Hose Guide

Output

Port

Special

Hose

Adapter

Flexible

Hose

Fiber

Washer

Flexible

Hose

Screen

Washer

113781-2-BB 8 Kohler Co.

7. Connect the Flexible Hoses

NOTE: The diverter elbow assemblies pivot to simplify hose

connections.

Insert one ﬁber washer into the open ends of all the ﬂexible

hoses.

Thread one ﬂexible hose onto each ″Cold″and ″Hot″valve body

outlet.

Connect the ″Cold″ﬂexible hose onto the right diverter port of

the three-way elbow assembly.

Connect the ″Hot″ﬂexible hose onto the left diverter port of the

three-way elbow assembly.

Thread a ﬂexible hose onto the spout adapter. Connect this hose

to the elbow assembly diverter port.

3-Way Elbow Assembly Elbow Assembly

Spout

Adapter

Fiber Washer

Connected To Handshower

Valve Body

Outlets A

ABC

Kohler Co. 9 113781-2-BB

8. Installation Checkout

Ensure that all connections are tight.

Open the drain.

Turn on the main water supply and check for leaks. Repair as

needed.

Open both hot and cold valves and run water through the spout

(if installed) to remove debris. Check for leaks.

Press the rear corner of diverter (Lever A). Check that the water

is diverted to the handshower.

Turn the cold and hot handles off and then on. Verify that the

water ﬂow is diverted back to the spout and that the handshower

is off.

Turn the valves off.

Diverter

Lever

Handshower

Spout

113781-2-BB 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13925 Bedienungsanleitung

Kohler

Kohler K-2294 Bedienungsanleitung

Kohler

Kohler K-9530 Montageanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler K-3148 K-3150 Montageanleitung

Kohler

Kohler K-T16225 Bedienungsanleitung

Kohler

Kohler Kumin K-103K36-SANA-CP Bedienungsanleitung

Kohler

Kohler Fairfax K-12265-4-BN Montageanleitung

Kohler

Kohler K-26228T Bedienungsanleitung

Kohler

Kohler K-3671 Montageanleitung

Kohler

Kohler 77989T-8A Bedienungsanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler Avid K-97358-4-CP Bedienungsanleitung

Kohler

Kohler K-3048 Bedienungsanleitung

Kohler

Kohler 4179A-NA Bedienungsanleitung

Kohler

Kohler K-12183 Bedienungsanleitung

Kohler

Kohler K-9404 Bedienungsanleitung

Kohler

Kohler 5838W-7U-0 Bedienungsanleitung

Kohler

Kohler K-75449-BV Bedienungsanleitung

Kohler

Kohler K-251 Bedienungsanleitung

Kohler

Kohler K-10272 Montageanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler STANCE Bedienungsanleitung

Kohler

Kohler 77984T-4MU Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung