Kohler K-13960 Bedienungsanleitung

Installation Guide

Bedpan Washers

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“Español-1”

K-13960 K-13961

1034416-2-A

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems please don’t

hesitate to contact us. Our phone numbers and web site are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Adjustable

Wrench

Strap

Wrench Thread

Sealant

Phillips

Screwdriver

Blade

Screwdriver

Hex

Wrench

• 9/16" or larger drill

bit for wall material

• Rags

• Seat wrench (Kohler

#21261) or 7/16"

square bar

• O-Ring Lubricant

Plus:

1034416-2-A 2 Kohler Co.

Before You Begin

CAUTION: Risk of property damage. To support the bedpan

washer and piping, provide sufficient reinforcement or mounting

brackets as required inside the wall.

NOTE: Refer to the roughing-in diagram for dimensional

information.

Shut off the main valve and water supply.

Observe all local plumbing codes and building codes.

Plumb using 1/2″NPT pipe, or 3/8″NPT pipe, or 1/2″copper

tubing, elbows, and adapters. Secure the piping to reinforcements

in the wall.

Provide pipe holes in the ﬁnished wall according to the

roughing-in diagram.

Kohler Co. reserves the right to make revisions in the design of

bedpan washers without notice, as speciﬁed in the Price Book.

3/8" Cold

1/2" N.P.T.Discharge

to Spray

1/2" N.P.T.Supply to

Vacuum Breaker

1/2" N.P.T.

Supply to

Hose &

Spray

3/8"

N.P.T.

Pedal in Raised

Position for

Floor Cleaning

3 Mounting Holes

for 1/4" (6 mm)

Screws (Provide

Backing)

Finished

Floor

14"

(35.6 cm)

2-7/8"

(7.3 cm)

(12.7cm)

2-3/16"

(5.6 cm)

1/2"

(1.3 cm)

7-3/4"

(19.7 cm)

2-3/4"

(7 cm)

1-3/8" (3.5 cm)

2-1/4"

(5.7 cm)

14" (35.6 cm)

7-5/8"

(19.4 cm)

3/4"

(2 cm)

44" (111.8 cm) to

Floor Optional

13-1/2"

(34.3cm) 3-7/8"

(9.8 cm)

12-1/2"

(31.8 cm)

3/8" N.P.T

Inlet

5/16" (8 mm)

3" (7.6 cm)

1-1/4"

(3.2 cm)

Kohler Co. 3 1034416-2-A

1. Install the Vacuum Breaker

CAUTION: Risk of property damage. Do not subject the

vacuum breaker to continuous pressure for more than twelve

hours.

NOTE: Install the vacuum breaker at least 6″(15.2 cm) above the

ﬁxture rim. Consult local codes for vacuum breaker height.

NOTE: Apply a thread sealant where applicable.

Thread one 1/2″nipple into both the supply outlet piping and

the supply inlet piping. Ensure that the threads of each 1/2″

nipple extend beyond the ﬁnished wall.

Slide the wall bracket over both the 1/2″nipples until it is snug

against the ﬁnished wall.

Insert one sleeve through each hole of the wall bracket and

thread onto each 1/2″nipple. Secure with a seat wrench or a

7/16″square bar. Do not overtighten.

Finished

Wall

1-3/8"

(3.5 cm)

1/2" I.P.S.

Nipples

Wall Bracket

Sleeve

O-Ring

Outlet

Port

Socket Head

Screw

Vacuum Breaker

Body

Inlet Port

1034416-2-A 4 Kohler Co.

2. Complete Vacuum Breaker Installation

NOTE: Do not install the shroud until the roughing-in and ﬁnishing

is complete.

Lubricate and insert one O-ring into each outlet port and inlet

port on the vacuum breaker.

Slide the vacuum breaker assembly into both sleeves at the same

time. Secure with two socket screws. Tighten the socket screws

with a 5/32″hex wrench. Do not overtighten.

Rotate the shroud so the opening faces the back. Slide the shroud

over the vacuum breaker assembly. Ensure that the threaded pin

comes through the hole at the top of the shroud.

Thread the shroud cover onto the threaded pin until hand tight.

Cover

Slot

Shroud

Threaded Pin

Kohler Co. 5 1034416-2-A

3. Install the Foot Control Unit

Align the screw holes and place the base onto the back of the

valve. Secure with three ﬂathead screws.

Connect the lavatory or sink supply to the valve outlet using the

supply manufacturer’s instructions.

Secure the valve assembly to the ﬁnished wall with three ﬂathead

screws (not provided). Follow the roughing-in instructions that

are packed with the foot control valve.

Connect the cold and hot water supplies to the valve.

Slide the cover over the valve assembly. Ensure that the cover

does not have contact with a foot pedal. If a pedal touches the

cover, remove the cover and adjust the foot pedal.

To adjust a foot pedal, loosen the hex nut. Turn the adjustment

screw counterclockwise until the foot pedal can no longer touch

the cover. If more than one foot pedal is installed ensure that both

foot pedals are even. Tighten the hex nuts.

Turn on the main water supply. Use the key provided to fully

open the valve supply stops. Check for leaks. Repair as needed.

Slide the cover over the valve assembly. Secure with a plated

screw.

Hot and Cold Water

Supplies

Flathead

Screw

Base

Secure to

Wall.

Connect

Supply Here.

Valve

and

Base

Hex Nut and

Adjustment

Screw Foot

Pedals

Plated

Screw

Cover

Key

1034416-2-A 6 Kohler Co.

4. Install the Hose Assembly

Thread one end of the ﬂexible hose into the supply outlet.

Securely tighten.

Thread the other end of the ﬂexible hose into the nozzle assembly

outlet. Securely tighten.

Hang the nozzle from the supply clamp.

Kohler Co. 7 1034416-2-A

5. Installation Checkout

One Pedal Bedpan Washer

For a one pedal bedpan washer, turn on the main water supply.

Open both the check valve and the supply valve.

Check for leaks. Repair as needed.

Remove the aerator by turning it counterclockwise.

Run water through the hose for approximately one minute to

remove debris.

Test and verify that the nozzle operates normally.

Two Pedal Bedpan Washer

For a two pedal bedpan washer, repeat with the other check valve

and supply valve.

Turn the water off.

Remove any debris from the nozzle and reinstall.

Test and verify that the nozzle operates normally.

Aerator

1034416-2-A 8 Kohler Co.

Guide d’installation

Appareil de nettoyage à cuvettes

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et adresse Internet sont au verso. Merci encore d’avoir choisi

la compagnie Kohler.

Cléàmolette

Cléà

sangle Jointd'étanchéité

pourfiletage

Tournevis

cruciforme

Tournevisplat

Clé

hexagonale

• Mêche à mur de

9/16" ou plus large

• Chiffons

• Clé à empreinte

carrée (Kohler

#21261) ou barre

carrée de 7/16"

• Lubrifiant pour joint

torique

Plus:

Kohler Co. Français-1 1034416-2-A

Avant de commencer

ATTENTION : Risque d’endommagement du matériel. Pour

supporter l’appareil de nettoyage à cuvettes et la tuyauterie,

prévoir un renfort suffisant ou des montants de ﬁxation tel que

requis dans le mur.

REMARQUE : Se référer au plan de raccordement pour les

informations dimensionnelles.

Fermer la valve principale et couper l’alimentation d’eau

principale.

Respecter tous les codes de plomberie et de bâtiment locaux.

Mettre d’aplomb à l’aide d’un tube de 1/2″NPT, ou un tube de

3/8″N.P.T., ou un tube en cuivre de 1/2″, de coudes et

d’adaptateurs. Sécuriser la tuyauterie aux renforts dans le mur.

Prévoir des trous pour le tuyau dans le mur ﬁni selon le plan de

raccordement.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations sur

le design des produits et ceci sans préavis, comme spéciﬁé dans

le catalogue des prix.

3/8" Froid

Décharge au vaporisateur

de 1/2" N.P.T.

Alimentation au

reniflard de 1/2"

N.P.T.

1/2" N.P.T.

Alimentation

au tuyau &

vaporisateur

N.P.T. 3/8"

Pédale en

position élevée

pour nettoyage

du sol

3 Trous de fixation de

1/4" (6 mm) vis

(fournissent appui)

Sol fini

14"

(35,6 cm)

2-7/8"

(7,3 cm)

(12,7cm)

2-3/16"

(5,6 cm)

1/2"

(1,3 cm)

7-3/4"

(19,7 cm)

2-3/4"

(7 cm)

1-3/8" (3,5 cm)

2-1/4"

(5,7 cm)

14" (35,6 cm)

7-5/8"

(19,4 cm)

3/4"

(2 cm)

44" (111,8 cm) au

sol optionnel

13-1/2"

(34,3cm) 3-7/8"

(9,8 cm)

12-1/2"

(31,8 cm)

Entrée

N.P.T. 3/8"

5/16" (8 mm)

3" (7,6 cm)

1-1/4" (3,2 cm)

1034416-2-A Français-2 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-7127 Bedienungsanleitung

Kohler

Kohler K-8666X Bedienungsanleitung

Kohler

Kohler Iron Works K-7104 Bedienungsanleitung

Kohler

Kohler MODULO 72801T-4 Bedienungsanleitung

Kohler

Kohler K-18355T Bedienungsanleitung

Kohler

Kohler K-5814 Bedienungsanleitung

Kohler

Kohler K-433 Montageanleitung

Kohler

Kohler K-15599X Bedienungsanleitung

Kohler

Kohler K-1112 Montageanleitung

Kohler

Kohler 22327T-7 Bedienungsanleitung

Kohler

Kohler K-8816 Bedienungsanleitung

Kohler

Kohler STRAYT 37331A-4ND Bedienungsanleitung

Kohler

Kohler K-6907 Montageanleitung

Kohler

Kohler K-2816 Montageanleitung

Kohler

Kohler K-1954 Montageanleitung

Kohler

Kohler SKYLINE K-705879T-FM-SHP Bedienungsanleitung

Kohler

Kohler Coralais K-15286 Montageanleitung

Kohler

Kohler KARAT K-17555 Bedienungsanleitung

Kohler

Kohler July 16027 Bedienungsanleitung

Kohler

Kohler K-438 Montageanleitung

Kohler

Kohler 76633T-B Bedienungsanleitung

Kohler

Kohler PINOIR K-2015 Montageanleitung

Kohler

Kohler K-9511 Bedienungsanleitung

Kohler

Kohler K-7779 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung