Kohler K-1954 Montageanleitung

Installation and Care Guide

Touchless Flush

Français, page “Français-1”

Español, página “Español-1”

K-1954

1216369-2-D

Included Components/Recommended Tools

Before You Begin

CAUTION: Risk of property damage: Do not use lithium

ion batteries with this product. Exposing lithium ion batteries

to water can result in a ﬁre.

NOTICE: Risk of property damage. If the toilet is plugged, turn off

the water supply before attempting to unplug it. The sensor can be

inadvertently activated while unplugging the toilet, resulting in an

overﬂow.

NOTICE: Risk of product damage. Use of in-tank toilet cleaners

will damage this product. In-tank cleaners emit gases which will

damage the seals and corrode the interior components. Damage due

to use of in-tank cleaners voids the warranty.

IMPORTANT! This product is designed to work as a retroﬁt on

existing toilets, but will not work with all models or variations. The

steps required to install the touchless module to some models of

toilets may differ from those shown.

IMPORTANT! If you experience difficulty installing this product on

your style of toilet, review the compatibility list and installation

videos at KOHLER.com/TouchlessToilet.

NOTE: Most toilets can be conﬁgured as touchless ﬂush only

(recommended) or both handle ﬂush and touchless ﬂush. A hole

cover is provided for touchless only conﬁguration.

Pads

(To remove the trip lever)

(To trim the chain)

Recommended ToolsProvided Components

Chain

and

Clips

Emblem

Bracket

Module

Hole Cover

Nut

Vent Bridge (4) AA

Batteries

Battery Holder

1216369-2-D 2 Kohler Co.

Before You Begin (cont.)

NOTE: While it is not required, emptying most of the water from

the tank will allow for a more pleasant installation and reduce the

risk of damage to parts if they are dropped in the tank. Instructions

for this process are provided at the appropriate time.

NOTE: When replacing the batteries, consult the installation guide

or go to www.kohler.com and go to the product page for K-1954 if

additional information is required.

Before starting the installation, conﬁrm this product is compatible

with your toilet by visiting KOHLER.com/TouchlessToilet and

going to the product page for K-1954.

Before starting the installation, determine if you will use both the

handle ﬂush and touchless sensor, or be removing the handle and

covering the handle hole with the provided hole cover.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Kohler Co. 3 1216369-2-D

1. Remove the Handle

Touchless Only Conﬁgurations (recommended)

IMPORTANT! Do not install the batteries until instructed. The

sensor will activate when the batteries are installed, making it

difficult to complete the installation process.

NOTE: The steps in this section are recommended, but are optional

for most installations. If your installation will retain the handle, go

to the ″Determine the Bracket Location″section.

Remove the Handle Components

Turn off the water supply to the toilet.

Flush the toilet to remove most of the water from the tank.

Disconnect the chain from the handle.

If the tank has a canister (shown), reattach the chain to itself near

the canister attachment point.

Remove the handle assembly (the nut on the handle assembly

will most likely loosen clockwise).

IMPORTANT! If your model of toilet has a ﬂoat attached to the

handle chain, the ﬂoat must not be removed. The ﬂoat is critical for

proper ﬂushing performance.

Install the Handle Hole Cover

Chain

Hole Cover

Nut

Flush Valve

Handle

Fill Valve

1216369-2-D 4 Kohler Co.

Remove the Handle (cont.)

NOTE: The hole cover is available in other colors. Go to

KOHLER.com, call the contact numbers on the back of this

document, or contact the retail outlet where you purchased this

product for other options.

Remove the nut from the hole cover if it is attached.

Insert the hole cover in the handle opening in the toilet tank.

Secure the hole cover with the nut.

Kohler Co. 5 1216369-2-D

2. Determine the Bracket Location

If the water supply was not turned off previously, turn off the

water supply to the toilet.

If there is still water in the tank, ﬂush the toilet to remove most

of the water from the tank.

Close the toilet seat and seat cover to avoid dropping parts in the

bowl.

Remove the tank lid and with the back of the lid toward you

position it upside down on the seat cover or a surface covered

with a towel or other soft material.

Recommended: For tank lid stability, install four pads, two on the

front and two on the back, near each corner of the tank rim

where the lid contacts the tank rim. The pads stabilize the lid,

helping to stop false ﬂushes when the lid is bumped.

Position the module upside down on the right side of the lid,

against the inside of the lid ledge.

Position and hold the bracket on the back ledge as shown.

Note the number of the slot closest to the bottom tab.

Slot

Bottom Tab

Ledge Bracket

Back of Lid

Module

Tank Lid

Top Tab

Pad

1216369-2-D 6 Kohler Co.

Determine the Bracket Location (cont.)

Remove the module from the tank lid and turn it lid side up.

Install the bracket, inserting the top tab in the slot determined in

the previous step.

Move the tank lid to a safe location.

Kohler Co. 7 1216369-2-D

3. Position the Module

Flapper Style

NOTE: For most ﬂapper installations, install the module above the

ﬂapper, with the center of the ﬂapper located directly below the

wheel. On some models of toilets, it may be necessary to relocate

the hose to avoid interference with the module.

If the bracket location is on a vent, install the supplied bridge

over the vent.

Position the module with the wheel directly above the center of

the ﬂapper.

Conﬁrm the hose does not interfere with the rotation of the wheel

(manually rotate the wheel). Adjust the position of the hose as

needed.

Canister Style

If the bracket location is over a vent, install the supplied bridge

over the vent to keep the module level.

Locate the module 1″(25 mm) to the side of the canister away

from the ﬁll valve.

Flapper

Center

of Flapper

Canister StyleFlapper Style

1" (25 mm)

Hose

Overflow

Vent

Bridge

Wheel

1216369-2-D 8 Kohler Co.

4. Adjusting the Module Location

NOTE: To achieve optimal module range and performance, the top

of the module may either lightly contact the bottom of the tank lid

or be within 1/4″(6 mm) of the bottom of the lid. The tank lid and

module can be in contact with each other when the module is

installed, as long as the tank lid sits on the tank correctly when

closed.

Position the tank lid on the tank. Check for ﬁt. Conﬁrm the pads

are correctly installed.

Conﬁrm the module height allows the tank lid to rest in the

correct position.

If the module or bracket interferes with the tank lid, ﬁrst conﬁrm

the bracket is tight against the rim of the tank.

NOTE: To conﬁrm the tank lid is within 1/4″(6 mm) of the

module, place four quarters on the module. If the tank lid touches

the quarters, the module is within 1/4″(6 mm) of the tank lid.

Conﬁrm the top of the module is within 1/4″(6 mm) or contacts

the bottom of the tank lid.

Adjust the bracket height as needed until the correct module

position is achieved.

Move the tank lid to a safe location when the adjustments are

complete.

1/4" (6 mm) Maximum

Lid

Kohler Co. 9 1216369-2-D

5. Connect the Module - Flapper Style

IMPORTANT! For optimal ﬂushing performance, in models where

a ﬂoat is integrated in the existing handle chain, the ﬂoat must not

be removed. Use the chain with the ﬂoat attached. Extend the chain

using the provided chain if needed.

Connect the Module

IMPORTANT! Risk of product damage. Never position the module

with the chain angled from the wheel to a point under the module.

The chain will wrap onto the wheel axel, resulting in continuously

running water and damage to the module.

IMPORTANT! For optimal ﬂushing performance, there must be less

than 1/4″(6 mm) of slack in the chain. The chain must run

vertically or at a slight angle away from the ﬂapper. Flushing

performance will decrease if the chain has too much slack or is at an

extreme angle.

Remove the large clip from the chain supplied with the touchless

kit.

Clip

Large

Cut here.

Hose

Adjust location

as needed.

Wheel

Incorrect Correct

Float

Center

Flapper

1216369-2-D 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-302 Bedienungsanleitung

Kohler

Kohler Moxie K-14292 Montageanleitung

Kohler

Kohler K-10094 Montageanleitung

Kohler

Kohler K-T609 Bedienungsanleitung

Kohler

Kohler K-146 Montageanleitung

Kohler

Kohler K-7145 Montageanleitung

Kohler

Kohler 16366 Bedienungsanleitung

Kohler

Kohler JULY Series Bedienungsanleitung

Kohler

Kohler k-10950 Betriebsanleitung

Kohler

Kohler K-14675X Bedienungsanleitung

Kohler

Kohler EVOKE 6332T-B4 Bedienungsanleitung

Kohler

Kohler K-15261 Montageanleitung

Kohler

Kohler STRAYT 37337T-B4 Bedienungsanleitung

Kohler

Kohler K-8593 Montageanleitung

Kohler

Kohler PureWarmth K-10349-96 Montageanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler TOUCHLESS 32323T-4 Bedienungsanleitung

Kohler

Kohler 23510-BL Bedienungsanleitung

Kohler

Kohler K-8207 Bedienungsanleitung

Kohler

Kohler Serif 5 BubbleMassage K-1337-G Bedienungsanleitung

Kohler

Kohler K-3099 Bedienungsanleitung

Kohler

Kohler K-45135 Montageanleitung

Kohler

Kohler K-377 Bedienungsanleitung

Kohler

Kohler 16316-4FP Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung