Kohler K-14402 Bedienungsanleitung

Installation Guide

Single-Control Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-14402 K-14404

1032026-2-D

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Inspect the supply tubing for damage. Replace as necessary.

If possible, install this faucet to the lavatory before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Thread

Sealant Plumbers

Putty

Hex

Wrench

1032026-2-D 2 Kohler Co.

1. Install the Faucet

Apply plumbers putty or other sealant to the underside of the

escutcheon according to the manufacturer’s instructions.

Feed the faucet supply inlets through the faucet hole of the

lavatory, then position the faucet. Slide the bracket and washer

over the stud and tighten the nut to secure.

Proceed to the installation instructions for your particular drain

style.

Nut

Bracket

Lavatory

Stud

Supply Inlet

Washer

Escutcheon

Nut

Bracket

Washer

Apply Plumbers

Putty.

Stud

Supply Inlet

Escutcheon

Apply Plumbers

Putty.

Kohler Co. 3 1032026-2-D

2. Install the Touch-Activated Drain

If present, remove the protective plastic cap from the drain and

discard.

Remove the nut, washer, and gasket from the drain body.

Apply a bead of plumbers putty or other sealant around the

underside of the ﬂange according to the sealant manufacturer’s

instructions.

For drains with metal stoppers: Close the drain and rotate the

drain body until the logo is positioned horizontally.

Insert the drain into the drain hole and press into place.

Slide the gasket (tapered side up) onto the drain body.

Slide the washer over the threads on the drain body.

Thread the nut up the drain body until snug against the

underside of the lavatory. Use care not to rotate the drain while

tightening the nut.

Using a wrench, tighten the nut.

Remove any excess putty or sealant.

Connect the P-trap to the drain body.

Washer

Flange

Drain Body

Nut

Tapered Gasket

Thick Tapered Gasket

(for thin-walled vessel style

lavatory installations)

1032026-2-D 4 Kohler Co.

Install the Pop-Up Drain

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Washer

Nut

Drain Body

Fixture

Thick Tapered Gasket

(for thin-walled vessel style

lavatory installations)

Kohler Co. 5 1032026-2-D

Complete the Pop-Up Drain Installation

IMPORTANT! If the tailpiece has been removed, double check that

the plastic washer is installed inside the ﬂange body or the drain

will leak.

Connect the P-trap to the tailpiece.

Press the seal into the lift rod hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

lift rod hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Check for leaks.

Thumb

Screw

Body

Clip

Stopper

Flange

Seal

Rod Nut

Tailpiece

Rod

Plastic Washer

Stopper Rod

Link

1032026-2-D 6 Kohler Co.

3. Connect the Supplies

CAUTION: Risk of restricted water ﬂow and product

damage. Use extreme care when bending the supplies to

avoid kinking.

CAUTION: Risk of product damage. Do not overtighten the

connections.

If the lavatory is not installed, install it at this time. Follow the

lavatory manufacturer’s instructions.

Connect the supply tubes to the supply stops. (Left is hot - right

is cold.)

Tighten the connections with an adjustable wrench.

Supply

Stop

Supply

Hose

Kohler Co. 7 1032026-2-D

4. Installation Checkout

Connect the drain tailpiece into the P-trap.

Ensure all connections are tight.

Remove the aerator and remove any debris.

Turn on the main water supply and check for leaks. Repair as

needed.

Lift and rotate the faucet handle to the full hot position, then the

full cold position. Run water through the spout for about one

minute to remove any debris. Check for leaks and repair as

needed.

Push the lever handle down to close the water supplies, then

reinstall the aerator.

Aerator

1032026-2-D 8 Kohler Co.

5. Optional Temperature Limiting Adjustment

Carefully pry the plug button off of the lever handle with a small

ﬂat-blade screwdriver.

Loosen the setscrew with a hex wrench, then remove the lever

handle.

Note the position of the locking ring relative to the inner geared

ring.

NOTE: To avoid damage to the locking ring during removal, pry

each side of the locking ring off the inner geared ring with an equal

and even technique.

Gradually pry each side of the locking ring up off of the inner

geared ring and onto the valve stem with a ﬂat-blade screwdriver.

Rotate the locking ring clockwise to increase temperature, or

counterclockwise to decrease temperature.

Align the geared teeth, then slide the locking ring down until

ﬂush against the inner geared ring.

Reinstall the lever handle.

Test the temperature setting. Repeat the above steps, if needed.

Retighten the setscrew.

Press the plug button into place.

Setscrew

Handle

Inner Geared

Ring

Locking

Ring

Plug Button

Inner Geared

Ring

Locking

Ring

Kohler Co. 9 1032026-2-D

Guide d’installation

Robinet mono-contrôle de lavabo

Outils et matériels

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Inspecter si la tuyauterie d’alimentation est endommagée.

Remplacer si nécessaire.

Si possible, installer le robinet au lavabo avant d’installer ce

dernier.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Clé à molette Joint

d'étanchéité

pour filetage

Mastic de

plombier

Clé

hexagonale

Kohler Co. Français-1 1032026-2-D

Andere Handbücher für K-14402

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-T72771 Montageanleitung

Kohler

Kohler K-11660 Montageanleitung

Kohler

Kohler Levity K-706013-L Bedienungsanleitung

Kohler

Kohler Sterling TS27370-4G Bedienungsanleitung

Kohler

Kohler K-T45115 Montageanleitung

Kohler

Kohler Memoris 10435T Bedienungsanleitung

Kohler

Kohler REVIVAL K-T16119 Bedienungsanleitung

Kohler

Kohler ARTIFACTS 72798T Bedienungsanleitung

Kohler

Kohler K-5834 Montageanleitung

Kohler

Kohler K-18829 Bedienungsanleitung

Kohler

Kohler MF0002KE-00 Bedienungsanleitung

Kohler

Kohler K-7116 Montageanleitung

Kohler

Kohler Sterling 20243 Montageanleitung

Kohler

Kohler Clearflo K-7147 Bedienungsanleitung

Kohler

Kohler 8959X-9 Bedienungsanleitung

Kohler

Kohler KUMIN K-18655T-B-CP Bedienungsanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler K-6907 Montageanleitung

Kohler

Kohler K-T13133 Bedienungsanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler K-514 Bedienungsanleitung

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler 23776T-7 Bedienungsanleitung

Kohler

Kohler BodySpa K-1030 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung