Kohler K-T16225 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

K-T16225, K-T16233, K-T16234,

K-T16235, K-16246

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1059598-2-C

IMPORTANT INSTRUCTIONS

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard. The pressure-balanced valve will not compensate for

changes in the water supply temperature; adjust the maximum

water temperature setting of this pressure-balanced valve when

such changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

NOTICE: Only apply silicone based lubricants to these valves. Do

not use petroleum based lubricants. Petroleum based lubricants will

harm the O-rings, seals, and plastic components.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1059598-2-C 2 Kohler Co.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

Before installing the trim, determine if the maximum water

temperature is acceptable to the user. If temperature adjustment is

needed, refer to the ″Optional Temperature Limiting Adjustment″

section of this guide.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″OFF″

position.

Shut off the main water supply.

The handle assembly illustrations shown may not represent your

actual product. The installation instructions still apply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Thermometer

Plus:

• 1/2" NPT Pipe Nipple

Strap

Wrench

Silicone

Sealant

Thread

Sealant

Plumbers

Putty

Hex

Wrench

Assorted

Screwdrivers

Kohler Co. 3 1059598-2-C

1. Install the Spout

Remove the temporary nipple.

Apply thread sealant and install a 1/2″nipple so it extends 7/16″

(1.1 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple and thread the spout onto the

nipple.

Carefully tighten with a clean strap wrench.

Remove any excess putty.

1/2" Nipple

K-16246

K-496-V

7/16"

(1.1 cm)

Apply plumbers

putty.

1059598-2-C 4 Kohler Co.

2. Install the Showerhead

NOTICE: Do not use thread sealant compound (pipe dope) on the

shower arm threads. Instead, use thread sealant tape on the shower

arm threads. This will avoid clogging the showerhead spray outlets.

Remove the temporary nipple from the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the wall ﬂange according to the manufacturer’s instructions.

Slide the wall ﬂange onto the shower arm.

Apply thread sealant tape to the threads shower arm and install

the shower arm to the shower elbow.

Carefully tighten shower arm to the shower elbow with a clean

strap wrench.

Press the ﬂange against the ﬁnished wall and secure to the

shower arm by tightening the setscrew.

Remove all excess putty.

With the showerhead off, run hot and cold water through the

shower arm to ﬂush out dirt and debris.

Apply thread sealant tape to the shower arm and thread the

showerhead to the shower arm.

Use a clean strap wrench to tighten the showerhead.

Check for proper operation.

Apply thread

sealant tape.

Setscrew

Flange Shower Arm

Showerhead

Apply plumbers

putty.

Kohler Co. 5 1059598-2-C

3. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. To eliminate the risk of

scalding, the water temperature should never be set above

120°F (49°C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

1059598-2-C 6 Kohler Co.

4. Install the Diverter Assembly

For K-T16233–3 and K-T16233–4 Models

Remove and discard the plaster guard and/or dome, if installed.

Position the actuator over the diverter stem. Tighten the setscrew.

Slide the guide over the actuator and thread it onto the diverter

stem.

Tighten the knob onto the actuator.

Guide

Setscrew

Actuator

Diverter Assembly

Discard plaster

guard with dome.

Diverter Stem

Valve Stem

Knob

Kohler Co. 7 1059598-2-C

5. Install the Valve Trim

NOTICE: For K-306-KS valve: The thin wall installation kit (88526)

is required for ﬁberglass or acrylic installations.

NOTE: The handle assembly illustrated may not represent your

actual product. The installation instructions still apply.

For installation over a tiled wall, apply a bead of silicone sealant

around the back edges of the escutcheon.

Break off the tab at the lower right on the backing plate. Fit the

backing plate over the valve so the large hole is on the bottom

and secure with two screws. Do not overtighten.

Rotate the valve stem fully counterclockwise.

Position the escutcheon over the backing plate and thread the

collar into the backing plate. Do not cross thread.

Insert the sleeve into the notches of the collar and hand tighten. If

the collar does not thread into the backing plate, thread the

backing plate screws 1/2 turn back.

Turn the sleeve around so the cutout in the sleeve faces away

from the wall.

Place the handle assembly over the valve stem and tighten the set

screw.

Escutcheon

Collar

Sleeve

Setscrew

Handle

Assembly

Screws

Tab

Valve Stem

Backing

Plate

1059598-2-C 8 Kohler Co.

Guide d’installation

Baignoire mono-contrôle et garniture de

douche

INSTRUCTIONS IMPORTANTES

AVERTISSEMENT : Risque de brûlures ou autres blessures

graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition de débit

croisé au régulateur et modiﬁer la température de l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements de température d’eau saisonniers,

et le remplacement ou l’entretien du chauffe-eau, changeront la

température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures. La valve à pression

réguléene compensera pas les changements de température

d’alimentation d’eau; ajuster la température maximale de cette

valve à pression équilibrée si de tels changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

AVIS : Seuls des lubriﬁants à base de silicone devraient être

appliqués à ces valves. Ne pas utiliser de lubriﬁants à base de

pétrole. Des lubriﬁants à base de pétrole peuvent endommager les

joints-toriques, les joints et les composants en plastique.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

Kohler Co. Français-1 1059598-2-C

INSTRUCTIONS IMPORTANTES (cont.)

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

NOTICE IMPORTANTE AUX INSTALLATEURS! Veuillez remplir le

coupon dans le guide du propriétaire ainsi que sur l’étiquette de la

valve. Conserver le guide du propriétaire pour future référence.

Outils et matériels

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Le mur ﬁni ou la baignoire/douche doit être installé avant

d’installer cette garniture.

Avant d’installer la garniture, déterminer si la température

maximum de l’eau est acceptable. S’il un réglage de température

est nécessaire, se référer à la section ″Réglage optionnel de

limitation de température″de ce guide.

La valve s’arrête par pression d’eau. Ne forcer la poignée dans

aucune direction. Pour fermer la valve, la tourner doucement sur

la position ″OFF″.

Couper l’alimentation d’eau principale.

Les illustrations d’ensemble de poignée peuvent être différentes

de votre produit actuel. Les instructions d’installation

s’appliquent tout de même.

Thermomètre

Plus:

• Mamelon tuyau 1/2" NPT

Clé à

sangle

Mastic à la

silicone

Joint

d'étanchéité

pour filetage

Mastic de

plombier

Clé

hexagonale

Tournevis

assortis

1059598-2-C Français-2 Kohler Co.

Andere Handbücher für K-T16225

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler ECO 72685T-B7 Bedienungsanleitung

Kohler

Kohler K-6132 Montageanleitung

Kohler

Kohler K-377 Bedienungsanleitung

Kohler

Kohler Mira Honesty Bedienungsanleitung

Kohler

Kohler K-13132 Montageanleitung

Kohler

Kohler Stance 14787A Bedienungsanleitung

Kohler

Kohler CUFF 37305M-4 Bedienungsanleitung

Kohler

Kohler K-2829 Bedienungsanleitung

Kohler

Kohler K-8801 Montageanleitung

Kohler

Kohler K-6907 Montageanleitung

Kohler

Kohler rada Exact-3 B Bedienungsanleitung

Kohler

Kohler K-10540 Montageanleitung

Kohler

Kohler Triton K-T7019 Bedienungsanleitung

Kohler

Kohler 10879T-4 Bedienungsanleitung

Kohler

Kohler K-7401 Montageanleitung

Kohler

Kohler K-99255X-4CD Montageanleitung

Kohler

Kohler K-5826 Montageanleitung

Kohler

Kohler K-6503 Bedienungsanleitung

Kohler

Kohler GANDIDE 11685T-4 Bedienungsanleitung

Kohler

Kohler 17493W-CP Bedienungsanleitung

Kohler

Kohler K-7605 Bedienungsanleitung

Kohler

Kohler Fairfax K-12185 Montageanleitung

Kohler

Kohler K-4107X Bedienungsanleitung

Kohler

Kohler Sterling 20243 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung