Kohler K-18486 Montageanleitung

Installation and Care Guide

Bath Filler with Handshower

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-18486 K-18492

1219580-2-A

Tools and Materials

Before You Begin

NOTE: This product may be installed as freestanding (installed

onto riser tubes) or deck-mount (installed onto the bath deck).

Follow the sections that pertain to your installation.

For Freestanding Installations

NOTICE: Discard the following hardware provided with the bath

ﬁller: support plate (1), threaded brass tubes (2), nuts (4), ﬁber

washers (4), and screws (8).

NOTICE: Do not remove the protective wrap from the riser tubes

until instructed to do so.

For All Installations

Observe all local plumbing and building codes.

Shut off the water supply.

IMPORTANT! For proper drainage of the spout, install the bath

ﬁller to a level surface.

3 mm,

5/16", 1/4"

Solder

Plus:

• Two 1/2" NPT Male

Copper Connectors

• Two 12" (305 mm) Long,

1/2" Copper Tubes (Deck-Mount)

• Two 30" (762 mm) Long,

1/2" Copper Tubes (Freestanding)

Drill and

Hole Saw

Thermometer

Sealant Tape

Strap

Wrench

Hacksaw or

Tubing Cutter

1219580-2-A 2 Kohler Co.

Roughing-In – Freestanding

No change in measurements if connected with the drain

illustrated (K-11344).

To properly plan for the installation, use the cut-out template

provided with your bath along with the roughing-in dimensions

above.

2-15/16" (75 mm)

5-9/16" (141 mm)

Ø 2-5/8"

(67 mm)

11-1/4"

(286 mm)

14-1/16"

(357 mm)

5-3/4"

(146 mm)

8" (203 mm)

22" (559 mm)

22-1/4"

(565 mm)

Kohler Co. 3 1219580-2-A

Roughing-In – Deck-Mount

NOTE: If the bath ﬁller is installed with the K-11343 drop-in bath,

ensure the distance between the centerline of each marked hole and

the ﬂange contacting the bath deck is a maximum of 4″(102 mm).

To ensure that water will not drip outside of the bath, properly

position the faucet on the deck so the outlet will be located inside

the bath.

To properly plan for the installation, use the cut-out template

provided with your bath along with the roughing-in dimensions

above.

2-15/16"

(75 mm)

5-9/16"

(141 mm)

Ø 2-5/8"

(67 mm)

11-1/4"

(286 mm)

14-1/16"

(357 mm)

(203 mm)

5-3/4"

(146 mm)

1219580-2-A 4 Kohler Co.

1. Assemble the Bath Filler

NOTE: The bath ﬁller arms are NOT identical. The setscrew holes

on the long end of the arms should face each other.

Determine the left and right side arms.

Apply lubricant (provided) to the O-rings on the bath ﬁller body.

Attach the short end of the arms to the bath ﬁller body.

Usinga3mmhexwrench, secure each arm with a large setscrew.

Orient the handshower bracket with the large side of the taper

facing up.

NOTE: The handshower bracket should be assembled

perpendicular to the arm so the handshower hangs over the bath.

Slide the handshower bracket onto the arm for the hot water

supply.

Using a 5/16″hex wrench, tighten the small setscrews to secure

the bracket at the desired height.

Arm

Large

Setscrew

Small

Setscrews

Handshower Bracket

(Large Side Up)

Bath Filler

Body

O-Ring

Kohler Co. 5 1219580-2-A

2. Prepare the Site – Freestanding

Use the template provided with the riser tubes to mark the

location of the water supply lines from the bath drain.

Verify the distances between the centerlines of the holes according

to the dimensions above.

Drill the supply holes using a 1-5/8” drill bit or hole saw.

Insert the riser support through the holes. Secure to the subﬂoor

with eight wood screws (provided).

NOTE: To protect the riser support from debris when installing the

ﬁnished ﬂoor, position the thread protectors (provided) in the holes.

Install 1/2″water supply tubing. The total tubing height from the

ﬁnished ﬂoor with a 1/2″NPT male connector should be

21-9/16″(548 mm).

Install the ﬁnished ﬂoor.

Solder 1/2″NPT male copper connections to the water supply

lines. Verify the height to the top of these connections is 21-9/16″

(548 mm) from the ﬁnished ﬂoor.

Apply thread sealant to the male connection on each water

supply tube.

Subfloor

Wood

Screw

5-15/16"

(151 mm)

22"

(559 mm)

Drain

Hole

Riser

Support Supply

Tube

1/2" NPT Male

Connection

21-9/16"

(548 mm)

Finished

Floor

1219580-2-A 6 Kohler Co.

3. Install the Riser Tubes – Freestanding

Thread the riser tubes fully into the riser support but do not

completely tighten the tubes.

NOTE: The distance from the ﬁnished ﬂoor to the top of the

installed coupling assemblies should be 24-7/16″(621 mm).

Thread a coupling assembly onto each water supply connection,

then tighten with a wrench. Verify the height to the top of the

coupling assemblies is 24-7/16″(621 mm) from the ﬁnished ﬂoor.

Install the plastic pipe plugs (provided) into the coupling

assemblies.

Turn on the water supply.

Check for leaks. Adjust as needed.

Turn off the water supply.

Remove and discard the pipe plugs.

Unthread the riser tubes out of the riser support and onto the

coupling assemblies until hand-tight.

Slide a gasket and escutcheon over each riser tube down to the

ﬁnished ﬂoor. Position the setscrew holes toward the bath.

Using a 5/16″hex wrench, secure each escutcheon with a small

setscrew.

Supply

Tube

Riser

Tube

Coupling

Assembly

Riser

Support

24-7/16"

(621 mm)

Finished

Floor

Escutcheon

Plug

Gasket

Setscrew

Kohler Co. 7 1219580-2-A

4. Construct the Tee Assembly – Freestanding

Thread the fastener support into the side of the bath with a 1/4″

hex wrench. Do not overtighten.

Ensure the distance from the head of the fastener support to the

bath surface is approximately 1/2″(13 mm).

Thread the fastener rod into the fastener support.

Thread a bracket onto one end of the tee rod until hand tight.

Slide the tee rod through the tee.

Handtighten the remaining bracket onto the other end of the tee

rod.

Tee

Tee Rod

Bath

Bracket

Fastener

Rod

Fastener

Support

1/2"

(13 mm)

1219580-2-A 8 Kohler Co.

5. Complete the Installation – Freestanding

Remove the protective wrap from the riser tubes.

Slide the tee assembly onto the riser tubes with the setscrew holes

facing down. Do not secure the tee assembly at this time.

Apply lubricant (supplied) to the O-rings on the coupling

assemblies.

Insert the bath ﬁller arms onto the coupling assemblies. Ensure

the arms are ﬂush against the top of the riser tubes.

Secure the arms to the coupling assemblies with the large

setscrews.

Slide the tee assembly up to cover the seam between the arms

and the riser tubes.

Insert the fastener rod to the center of the tee assembly.

Secure the tee assembly with two small setscrews on the

underside of the tee.

Secure the brackets with small setscrews.

Proceed to the ″Install the Handshower″section.

Bracket

Arm

Riser Tube

Fastener Rod

O-Rings

Small Setscrews

Large Setscrews

Kohler Co. 9 1219580-2-A

6. Prepare the Site – Deck-Mount

NOTE: Provide an access panel under the bath deck for water

supply connections.

NOTE: Reference the ″Rough-In – Deck-Mount″section of this

guide before proceeding.

Position the support plate on the bath deck where the water

supply tubing will be located. Trace the holes.

Verify that the location of the plate will allow the bath ﬁller spout

to reach into the bath.

Verify the distance between the centerline of the marked holes is

5-15/16” (151 mm).

NOTE: If a hole saw will be used, drill outside the line of the

marked holes.

Drill the holes using a 1-9/16” drill bit or 1-1/2″hole saw.

Remove any debris after drilling.

Verify the drilled holes will accommodate the riser tubes. Adjust

the hole diameter slightly, if needed.

Secure the support plate to the unﬁnished bath deck with the

eight (provided) wood screws.

Bath Deck

Screw

5-15/16"

(151 mm)

Support Plate

Check the reach.

1219580-2-A 10 Kohler Co.

Andere Handbücher für K-18486

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Coralais K-15186 Montageanleitung

Kohler

Kohler K-7549 Montageanleitung

Kohler

Kohler K-11810 Bedienungsanleitung

Kohler

Kohler K-2293 Montageanleitung

Kohler

Kohler K-T72771 Montageanleitung

Kohler

Kohler STRAYT 37331T Bedienungsanleitung

Kohler

Kohler K-4108T Bedienungs- und Wartungsanleitung

Kohler

Kohler Botticelli K-2333 Bedienungsanleitung

Kohler

Kohler K-13132 Montageanleitung

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler Strayt Bedienungsanleitung

Kohler

Kohler Jarves K-5055 Bedienungsanleitung

Kohler

Kohler Portrait K-2272 Bedienungsanleitung

Kohler

Kohler 31138T-4 Bedienungsanleitung

Kohler

Kohler MODULO 99960T-4V Bedienungsanleitung

Kohler

Kohler 24270T-CP Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.8 kW Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Kohler

Kohler GANDIDE 11685T-4 Bedienungsanleitung

Kohler

Kohler URBANITY 23748T-9 Bedienungsanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler JULY Series Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung