Kohler 24270T-CP Bedienungsanleitung

All information is based on the latest product information

available at the time of publication, Kohler Co. reserves

the right to make changes in product characteristics,

packaging, or availability at any time without notice.

Please leave these instructions for the consumer. They

contain important information.

所有的资料是按最新出版的产品资料编写而成。

科勒公司保留任何时候不经通知即可改变产品特

性、包装或产品可供类型的权利。

说明书包括重要的安装、保养及清洁方面的内容，

请把这些资料交给用户阅读。

1. Flush the water supply pipes thoroughly to remove debris.

Faucet is designed for tap water or potable water.

2. Do not attack the faucet with rough strength to avoid

being damaged.

3. Do not damage the surface of sensing window when

installing or cleaning the faucet.

4. For new installations, install the faucet and drain to the

lavatory before installing the lavatory.

5.As for DC type faucets, please pay special attention to

insert direction match of battery poles. Tighten the battery

cover completely to prevent its exposure to moisture.

6. As for AC type faucets, strictly follow indicated instructions

to perform electric connection. Only provide electric supply

to power box after the installation is completed.

1. 一定要先彻底冲洗供水管以清除管道中的杂

质，使用水源为自来水或可供饮用水。

2.请勿将强力及冲击施于产品，以免造成故障，

引起漏水。

3.安装、清洁龙头时，切勿损伤感应窗口表面，

以免造成故障。

4.如果是安装新的洗面盆，可将水龙头和排水组

件先安装好到面盆上。

5. 对于直流龙头，安装时注意电池的正负极不

能装反，电池盒盖要拧紧，防止电池受潮。

6. 对于交流龙头，安装时务必按照说明书的要

求正确连接导线，龙头安装完毕后才可向电源盒

供电。

Oblo Sensor Faucet

安装之前

Notes:

BEFORE YOU BEGIN

注意事项

安装说明书

欧宝

BLO

7. 修理面盆时，用黑色电工胶布粘住感应窗口。

7.. Cover the sensing window with black tape wh

8. 维修交流龙头时，必须断开交流电源并关闭

repairing lavatories.

水源。

8.. Turn off the electrical source and shut down wat

supplybeforethefaucetsrepaired.

24270T-CP

24271T-CP

24270T-S3-CP

24270T-S5-CP

OBLO DM SENSOR FCT-COLD,W/O P,0.5G,SP

欧宝台盆感应龙头,单冷,不含电源盒,1.9升,特供版

OBLO DM SENSOR FCT-MIXER,W/O P,0.5G,SP

欧宝台盆感应龙头,冷热,不含电源盒,1.9升,特供版

OBLO DM SENSOR FCT-COLD,W/O P,0.35G,SP

欧宝台盆感应龙头,单冷,不含电源盒,1.4升,特供版

OBLO DM SENSOR FCT-COLD,W/O P,0.26G,SP

欧宝台盆感应龙头,单冷,不含电源盒,1.0升,特供版

科勒（中国）投资有限公司

中国上海市静安区江场三路158号邮编：200436

制造商：上海科勒电子科技有限公司

中国上海市宝山区丰翔路1955号邮编：200444

1364728-T01-A

1. 手伸到出水口下方感应范围

内（感应距离随面盆、周围的情

况而自动调节），水龙头出水。

手离，0.5～2秒后，水龙头自动

止水。

1. Put your hand in the sensing -range, the

faucet should turn on. The faucet should turn

off after removal within 0.5~2 seconds. The

sensing distance will be adjusted automatically

as per the condition of the lavatory and

surrounding environment.

使用说明 OPERATION INSTRUCTIONS

2. 冷热混水龙头水温调节：先关

闭热水角阀，再将冷水角阀旋至

冷水最大状态，再缓慢打开热水

角阀，以免烫伤。如冷水水压

大，打开全部热水角阀后，仍无

合适水温，请再缓慢减少冷水出

水量，直至水温使用舒适。

2. Adjust the water temp for faucet with

temperature mixture: turn off hot water valve

first, and then turn on the water and adjust to

full cold, slowly turn on hot water valve to

avoid scalding. If cold water pressure is high

and unable to gain proper comfortable water

temp even hot water valve is fully open, turn

down cold water capacity slowly until water

temp is comfortable for use.

1364728-T01-A

注意：

请勿将龙头安装在台面上，

同时搭配台上盆。

Note:

please do not install the faucet on the

table and match the washbasin

排水组件

φ41.2

φ54

φ31.75

226

φ66.5

16305T-NA

AC/DC Transformer

(need to buy

separately)交流电源盒

Output: DC6V

输出:直流电压6V

Input: AC220V

输入:交流电压220V

安装尺寸 ROUGH-IN DIMENSIONS

24270T-CP

欧宝台盆感应龙头

（单冷型不含电源盒）

24270T-CP

欧宝台盆感应龙头

（单冷型不含电源盒）

The Drain

24271T-CP

欧宝台盆感应龙头

（冷热混合型不含电源盒）

205 205

136 136

The Top of Lavtory

台盆顶面

The Top of Lavtory

台盆顶面

用户自备角阀

G1/2 外螺纹

Please let user prepare external

thread stop valve G1/2

用户自备角阀

G1/2 外螺纹

Please let user prepare external

thread stop valve G1/2

AC/DC Transformer

(need to buy separately)

交流电源盒

（需另购）

1364728-T01-A

205

136

The Top of Lavtory

台盆顶面

24484T-NA

DC Power Unit

直流电源盒

直流电压6V

Output: DC6V

注：直流或交流电源盒需另购。 NOTE:DC Power or AC/DC transformer need purchasing.

骤步装安 INSTALLATION

一如何安装水龙头

1.龙头与面盆的安装固定

将固定螺杆(2)安装到水龙头底部(3)

处。再把垫片(4)套在固定螺杆上。并

嵌入水龙头底部的盘槽中。然后将电

源线(8)和进水软管(9)穿过安装孔，

从面盆下方将固定橡胶垫片(5)固定金

属垫片(6)和固定螺母(7)对齐固定螺

杆(2)向上套入。调整水龙头电源线

(8)及进水软管(9)的位置。用扳手拧

紧固定螺母(7)以便把水龙头固定在面

盆上。

How to Install the Faucet

1. Fixing the faucet and lavatory

Install the mounting stud (2) to the bottom

of the faucet (3), then slip the washer (4)

over the mounting stud and put them into

the groove on the spout. Insert the power

wire (8) and supply hose (9) into the hole

from underside of the lavatory. From

underside of the lavatory, slide the rubber

washer (5), meter washer (6) and fixed

nut (7) onto the mounting stud (2).

Tighten nut (7) to make faucet installed on

the lavatory.

技术参数 PARAMETERS

二安装阀体组件

关闭角阀(12)，

对于冷热混水型的阀体组件安装是先

将三通进水软管组件的两端与角阀

(12)连接，然后把阀体组件(10)进水

口处的保护帽旋出，将阀体组件(10)

进水口与三通进水软管组件(11)连

接；对于单冷型的阀体组件安装是把

阀体组件(10)进水口处的保护帽旋

出，将主阀体组件(10)进水口与角阀

(12)连接。

2. Install alve Assemly

Turn valve off (12).

For mixing water valve assembly

installation, connect water inlet hose

assembly to both ends of stop valve (12),

then unscrew valve assembly (10) water

inlet protection cap, connect valve

assembly (10) inlet to Tee water inlet

hose assembly (11); for cold water faucet

installation, unscrew valve assembly (10)

water inlet protection cap, connect valve

assembly (10) inlet to valve (12).

1364728-T01-A

约1.9L/min

0.35GPM 约1.4L/min

0.26GPM 约1.0L/min

超时用水控制：超时用水1分钟，自动止水。

环境温度：

1～55℃

进水温度：0.5～71℃

适用水压：0.05～

0.86MPa

流量： 0.5GPM

电源：直流 4节5号碱性电池(LR06×4)

交流电压220V,频率50/60Hz

检测时间：小于0.75秒

关阀延时：0.5～2秒

感应距离：自动调节 0.5GPM About 1.9L/min

0.35GPM About 1.4L/min

0.26GPM About 1.0L/min

Overtime Flowing Control: Automatically stop flushing when

the faucet senses an object for more than 1 minute

continuously

Ambient Temperature: 1~55℃

Supply Water Temperature: 0.5~71℃

Supply Water Pressure: 0.05~0.86MPa

Flow Rate:

Power: DC 4 pieces of AA size alkaline batteries

AC 220V, 50/60Hz

Senser Duration: Less than 0.75s

Shut-off Delay: 0.5~2s

Sensing Distance: Automatic adjustment

四如何安装排水组件

旋下排水器盘片(15)，在其底面沿

周围涂上一圈密封油灰。把排水

本体(16)由底下插入面盆。

How to Install the Drain

Screw off the drain flange (15) from drain.

Apply a ring of plumbers putty around

underside of the drain flange(15) . Insert

the drain body(16) into the lavatory from

the underside.

把尾管(18)接上存水弯(19)，尾管需

插入存水弯25mm到55mm之间。

Connect the tailpiece(18) to the trap(19).

The tailpiece should extend 25mm to

55mm into the trap.

Thread the drain flange (15) onto the drain

Body (16). Tighten the locknut (17) by hand

from the underside of the fixture. Remove

any excess putty.

Note: Do not try to change the position of

the drain after the locknut(17) is tightened,

or you may break the putty seal.

把排水器盘片(15)旋入排水本体

(16)。从下方用手拧紧锁紧螺母

(17)，去除多余的油灰。

注意：在锁紧螺母(17)拧紧后，不

可再调整排水本体的位置，否则将

会破坏油灰密封。

Apply plumbers putty

涂油灰

1. 取出电池盒组件，旋松螺钉

(13)，按电池盒盖(14)上的正负极

标示装入4节5号电池，紧锁电池

盒盖(14)的螺钉(13)后。

注意：电池极性不能装反，新旧

电池不能混用。

2. 在合适的位置打孔，打入膨胀管，

用自攻螺钉固定电池盒。将相同颜

色接插件分别连接。

注意：接插件位置朝上。

134

三安装电池组件

1364728-T01-A

如何安装交流电源盒

AC/DC transformer

交流电源盒

一个交流电源盒供一个感应龙头

接220V交流电

Connect AC 220V

Switch

开关

Wire Tube

穿线管

Wire connection pattern for one to one

Faucet

感应龙头

HOW TO INSTALL THE AC/DC

TRANSFORMER (ONLY USED

WITH TOUCHLESS FAUCET, AC)

(仅限于交流感应龙头)

Connect to

electrical Source

接交流电源

注意：禁止将交流AC220V接入直流DC接线端。

Connect to

Faucet

接感应龙头

Connect to

electrical Source

接交流电源

Connect to

Faucet

接感应龙头

Note: Not allowed connect AC 220V electrical source to DC wire connector of AC/DC transformer

注：交流电源盒需另购。 Note: AC/DC transformer need to buy separately.

1364728-T01-A

1. Install AC power unit (sticker on the back) dry, andavoid

showering, soaking from water. Customer prepare wire

tube and wire according to requirement. Wire tube

should be put into the wall. Suggested wire: AC connection

wire should with insulated protecting layer or sleeve and

the section should be bigger than 0.5mm . The section of

DC connection wire should be

bigger than 0.3mm . The

connection pattern must according to illustrations above.

2. After wire layout finished, check and repair if needed.

Then connect AC connector of AC/DC transformer to

electrical source from the control box, and DC connector of

AC/DC transformer to faucet. Turn on AC electrical power,

Faucet will commence auto-sense mode which will take

30s. The faucet will not work this period.

直流连接线采用导体标称截面积 mm 的电线。

请严格按照上图进行连接。

0.3

1.电源盒 (背面有不干胶)应安装在干燥，不会被水

淋湿、浸泡的位置。根据需要客户自备穿线管及

连接线。穿线管安装在墙内。建议交流电源线采用

带绝缘和护套层的电线，导体标称截面积 0.5mm ;

2. 排线完毕后，应检查并确保所有排、接线无误，

再分别连接电源盒AC接线端与排线管内交流接线

端，以及电源盒DC接线端（黑橙线接头）与龙头

的电源线接插件（从阀盒内引出的电线），最后

打开AC电源，龙头进入30秒自动调距阶段，此过

程龙头不会出水。

1364728-T01-A

如何转换成恒温阀感应龙头

(若用户另购

恒温阀16294T-3-CP,

具体安装详见其说明书

)

墙面

Wall

接感应龙头

Connect Sensor Faucet

角阀

Stop Valve 三通

Tee

出水口

Outlet

恒温阀

thermostatic valve

进热水

hot

进冷水

cold

注：软管、三通、角阀请用户自备。

角阀

Stop Valve

三通

Tee

三通

Tee

墙面

Wall

HOW TO CHANGE TO THERMOSTATIC

SENSOR FAUCET (If users buy the

thermostatic valve 16294T-3-CP, the

installation refer to the manual of

16294T-3-CP)

注：软管、三通请用户自备。

三通进水软管组件

Tee, Inlet Assy.

用户自备角阀G1/2外螺纹

Please prepare external

thread angle valve G1/2

Note: Please let users prepare the hose and tee by themselves.

MIN 50mm

Note: Please let users prepare the hose、tee and check

Valve by themselves.

1364728-T01-A

HOW TO CHANGE TO A MIXING

SENSOR FAUCET (If customerpurchases

tee inlet assy 1284583-SP)

如何转换成混水感应龙头

(若用户另购三通进水软

管组件1284583-SP)

建议使用科勒推荐的三通进水软管

组件，否则有冷热水互窜的风险。

It is recommended to use Kohler TEE inlet hose assembly,

otherwise there is a risk of cold and hot water mixing problem.

All Finishes: Clean the finish with a mild soap and warm

water. Wipe entire surface completely dry with a clean soft

cloth. Many cleaners may contain chemicals, such as

ammonia, chlorine, toilet cleaner etc. which could adversely

affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets

and fittings.

CLEANING INSTRUCTIONS

有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙

头及其配件上。

适用于所有加工处理过的表面，以中性肥皂水清

洗镀层表面，再以干净的软布彻底擦干整个表面。

许多清洁剂，比如氨水，去污粉及洁厕灵等，会

对电镀表面造成伤害，切忌使用。

安装结果检查

检查并确保所有衔接处都已拧紧，打开排水系统

和主要供水源，检查并修理有漏水的接口。

Check and ensure that all connections are tight. Open the

drain. Turn on main water supply and check for leaks.

Replace as required.

INSTALLATION CHECKOUT

用户须知

1. 感应指示灯的各种闪烁情况

(3) 间隔2秒钟连续闪烁：若直流感应龙

头, 代表龙头电池耗尽，已停止工作，等

待使用者更换电池;若交流感应龙头，表

示为两种情况：一种为刚刚停电；另一

种为在交流供电正常的情况下，则电源

盒直流接线端接触不良。

(4) 在正常工作情况下，当有物体被感应

时，龙头出水，感应指示灯闪烁一次。

（龙头关闭，感应指示灯不闪烁。）

IMPORTANT CONSUMER INFORMATION

1. Note of the Indicator Flashing

The indicator is the only and effective way to learn

the faucet's working conditions. So the users can

use the sensor faucet correctly with knowing the

meaning of the sensor indicator's flashing.

(1) Quick flashing means the faucet is in the

period of adjusting sensing distance after power

on for 30s. During these 30s, please do not

disturb auto adjustment or place objects within the

sensing range.

(2) The indicator flashes every 6 seconds (DC

type) indicates that the unit is out of battery and

has stopped working. Replease batteries.

(3) The indicator flashes every 2s: as for DC type

faucets, this indicates the unit is out of battery

and ceases working. Please replace batteries.

For AC faucet, it indicates two possibilities: one

is that the unit is out of battery; or poor DC

terminal contact under normal AC power supply.

(4) In normal condition, the water will flow and

the indicator will flash one time when objects are

inducted. (The indicator does not flash when

faucet stops flowing.)

清理说明

指示灯

超时出水控制

连续在感应状态下使用约一分钟，龙头自动止水。

自动止水后，手或物体离开感应范围后，再次进

入感应范围内，龙头正常工作，否则无反应。

2. Overtime Flowing Control

When the faucet works for about 1 minute continuously, the

water will be shut off automatically. After that, objects must

be removed from the sensing range. Then the water will

flow when objects go into the sensing range again.

Otherwise, the faucet will not work.

感应指示灯是使用者了解感应龙头有效、

唯一的途径。所以明白了感应指示灯闪烁

所代表的含义，可以正确使用感应龙头，

如图示:

(1)

快速闪烁，代表感应龙头正处于通电

后的30秒自动调节阶段。期间，安装者、

使用者不得干扰其自动调节，感应范围

内不要放置物体。

(2) 间隔6秒钟闪烁一次（直流版本），

表示电池即将使用完，请更换电池。

Indicator Light

1364728-T01-A

3.清洗过滤系统 3.Clean the Filtration System

The faucet includes connector assembly with high quality

filtration system. If there is a lot of debris in the supply pipes

or the quality of water is bad, it will cause the flow in bad

condition. Please clean th filtration system as following steps:

(1) Close the angle valve.

(2) Remove the valve assembly and take out the filter for

cleaning, then re-install it.

Notice: Make sure to install the filter washer after cleaning

the filter

该感应龙头的阀体组件内已包含了优良的过滤装

置。如管内杂质过多或水质较差，长期使用会引

起出水情况不良。请按以下步骤清洗过滤装置：

(1) 关闭角阀。

(2) 将主阀体组件取下，拿出滤网，用水冲洗完

毕后，重新装入。

注意：在清洗完滤网后，不要遗失平垫。

4.自动清洗存水功能 4. Self-Cleaning the stagnant water

When the faucet is no used for a long period of time, it will

automatically flush to discharge the stagnant water inside

the faucet every 24hrs.

感应龙头长期处于不使用状态时，每间隔24小

时自动冲水一段时间排出龙头内的存水。

1364728-T01-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-352 Bedienungsanleitung

Kohler

Kohler Loure K-15285 Montageanleitung

Kohler

Kohler K-72218-2BZ Bedienungsanleitung

Kohler

Kohler Symbol Rite-Temp K-T18488 Bedienungsanleitung

Kohler

Kohler Bancrof K-2347 Montageanleitung

Kohler

Kohler K-16135 Bedienungsanleitung

Kohler

Kohler K-7776 Montageanleitung

Kohler

Kohler Torsion Bedienungsanleitung

Kohler

Kohler Cachet Quiet-Close K-7671 Bedienungsanleitung

Kohler

Kohler K-11660 Montageanleitung

Kohler

Kohler Candide 660 Series Montageanleitung

Kohler

Kohler SUMMON K-24147T-7 Handbuch

Kohler

Kohler 1114111 Bedienungsanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler NEW MEMOIRS K-76555T Bedienungsanleitung

Kohler

Kohler K-7163 Montageanleitung

Kohler

Kohler HiRise K-7344-4 Montageanleitung

Kohler

Kohler K-6132 Montageanleitung

Kohler

Kohler K-T16225 Bedienungsanleitung

Kohler

Kohler Leighton K-2326 Montageanleitung

Kohler

Kohler STRAYT 37341-4 Bedienungsanleitung

Kohler

Kohler K-45210 Montageanleitung

Kohler

Kohler K-10430 Bedienungsanleitung

Kohler

Kohler K-251 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung