Kohler K-T461 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Faucet Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T461 K-T462

K-T463 K-T464

K-T465 K-T466

1011157-2-D

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1011157-2-D 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

We recommend that you determine if the maximum water

temperature is acceptable before installing this trim. If

temperature adjustment is needed, refer to the ″Water

Temperature Adjustment″section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″Off″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Assorted

Screwdrivers

Strap

Wrench

Plumbers

Putty

Hex WrenchThread Sealant Silicone Sealant

Thermometer

Kohler Co. 3 1011157-2-D

1. Install the Spout

Remove the temporary nipple from the bath elbow.

Apply thread sealant, and install a 1/2″nipple so it extends 7/16″

(1.1 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant to the back of

the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple, and install the spout to the

nipple.

Carefully tighten with a clean strap wrench.

Remove excess putty.

Spout

1/2" Nipple

7/16"

(1.1 cm)

Apply plumbers putty.

1011157-2-D 4 Kohler Co.

2. Install the Showerhead

CAUTION: Risk of product damage. To avoid plugging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower ell.

Apply a bead of plumbers putty or other sealant to the back of

the ﬂange according to the manufacturer’s instructions.

Slide the wall ﬂange onto the shower arm.

Apply thread sealant tape to the threads and install the shower

arm to the shower ell.

Carefully tighten with a clean strap wrench.

Press the ﬂange against the ﬁnished wall and secure to the

shower arm by tightening the setscrew.

Remove all excess putty.

With the showerhead off, ﬂush out the system.

Apply thread sealant tape to the shower arm and thread the

showerhead to the shower arm.

Use a clean strap wrench to tighten the showerhead.

Check for proper operation.

Flange

Setscrew

Showerhead

Flange

Ell

Apply thread

sealant tape.

Apply plumbers

putty.

Shower Arm

Kohler Co. 5 1011157-2-D

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature to ensure desired maximum water

temperature.

NOTE: After adjustment, complete the required information on the

valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

1011157-2-D 6 Kohler Co.

4. Install the Faceplate

CAUTION: Risk of damage to the K-306-KS valve assembly.

When using the K-306-KS HiFlow Valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Installing the Stately Faceplate

Remove and discard the plaster guard and/or dome, if installed.

For installation over a tiled wall, apply a bead of silicone sealant

around the back edges of the faceplate.

Fit the backing plate over the valve so the large hole is to the

bottom and secure with two screws. Do not overtighten.

Rotate the valve stem fully counterclockwise.

Position the faceplate over the backing plate and thread the collar

into the backing plate. Do not cross thread.

Insert the sleeve tabs into the collar notches and hand tighten.

Remove the sleeve from the collar and turn it around so the tabs

face outward.

Insert the sleeve into the collar so the slot is down and facing

outward.

Installing the Classic Faceplate

Remove and discard the plaster guard and/or dome, if installed.

Fit the faceplate over the valve and secure with two screws. Do

not overtighten.

Screw

Valve

Discard plaster guard with dome.

Backing Plate

Collar Sleeve

Faceplate

Tab

Sleeve Slot

Stately

Kohler Co. 7 1011157-2-D

Install the Faceplate (cont.)

Rotate the valve stem fully counterclockwise.

Slide the sleeve over the valve stem so the slot is down and

facing outward.

1011157-2-D 8 Kohler Co.

5. Install the Handle

Align the handle assembly so the lever handle points straight

down (lever handle only) and press it into the valve stem.

Turn the sleeve as needed so the notch lines up with the handle

assembly setscrew.

Secure the handle assembly in place by tightening the setscrew.

All InstallationsClassic

Valve

Faceplate

Screw

Slot

Sleeve

Setscrew

Discard plastic

guard w/dome.

Handle

Assembly

Handle

Assembly

Handle Assembly

Kohler Co. 9 1011157-2-D

Guide d’installation

Robinet baignoire mono-contrôle et garniture

de douche

INSTRUCTIONS IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou de blessures graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition

d’écoulement croisé au régulateur et modiﬁer la température de

l’eau.

•Les facteurs qui changent la température de l’eau alimentée à

cette valve, tels que les changements de température d’eau

saisonniers, et le remplacement ou l’entretien du chauffeau,

changeront la température maximale de l’eau fournie par le

régulateur et pourront présenter un danger de brûlures.

•La valve à pression équilibrée ne compensera pas les

changements de température d’alimentation d’eau; ajuster la

température maximale de cette valve à pression équilibrée si de

tels changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

Kohler Co. Français-1 1011157-2-D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-4000 Montageanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler 8022A Bedienungsanleitung

Kohler

Kohler K-438 Montageanleitung

Kohler

Kohler C3-050 Bedienungsanleitung

Kohler

Kohler CFI230G Bedienungsanleitung

Kohler

Kohler K-T72770 Montageanleitung

Kohler

Kohler Mira Event XS Bedienungsanleitung

Kohler

Kohler K-19481 Montageanleitung

Kohler

Kohler K-7273 Montageanleitung

Kohler

Kohler Thermostatic Electric Shower Bedienungsanleitung

Kohler

Kohler K-10217 Bedienungsanleitung

Kohler

Kohler K-12286-4 Montageanleitung

Kohler

Kohler K-3487 Bedienungsanleitung

Kohler

Kohler K-2338 Series Montageanleitung

Kohler

Kohler K-14663 Montageanleitung

Kohler

Kohler K-72777 Montageanleitung

Kohler

Kohler C3-050 Bedienungsanleitung

Kohler

Kohler K-T9540 Montageanleitung

Kohler

Kohler Moxie K-14292 Montageanleitung

Kohler

Kohler K-170 Montageanleitung

Kohler

Kohler K-3048 Bedienungsanleitung

Kohler

Kohler 72282T-4 Service-Handbuch

Kohler

Kohler OnCue Plus RDC Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung