Kohler K-2600 Bedienungsanleitung

Installation Guide

Self-Rimming/Undercounter Lavatories

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-2600 K-2602, K-2603

K-2605 K-2610

K-2611 K-2612

1018896-2-C

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

Observe all local plumbing and building codes.

Prior to installation, unpack the new lavatory and inspect it for

damage. Return the lavatory to its protective carton until you are

ready to install it.

Inspect the drain and supply tubing. Replace if necessary.

Do not substitute another sealant if one is supplied with this

lavatory.

Use the template supplied with the lavatory.

For replacement installations, make sure the existing cutout is the

same size or smaller than needed for the new lavatory.

Pencil Drill

Screwdriver

Keyhole Saw

Template

(supplied) Safety

Glasses Adjustable

Wrench

Tape

Measure

Plus:

• 1/2" drill bit

• Ruler

• Hole Saw

• Gloves

1018896-2-C 2 Kohler Co.

1. Preparation

Install the water supplies and drain piping according to the

roughing-in information.

Determine the faucet centerline location. Consider the faucet and

handle escutcheon diameters, the length of the spout, and the

clearance between the spout and the lavatory rim.

Calculate the faucet centerline measurement by ﬁrst dividing the

escutcheon diameter by 2, and then adding 1/4″(6 mm) to the

result. If necessary, round the calculation up to the nearest 1/16″

(2 mm).

Carefully draw the calculated faucet centerline on the cut-out

template. Choose the most suitable location based upon the

following factors:

•compliance with all local plumbing codes

•minimum 2″(5.1 cm) distance from the water stream to the

lavatory rim edge. This is important to ensure adequate clearance

for hand washing

•a minimum 1/4″(6 mm) distance between the faucet spout and

the lavatory rim

Redraw the faucet centerline as needed to meet these

requirements.

Draw a line on the cut-out template a minimum of 2″(5.1 cm)

behind the ﬁnal faucet centerline. This is the minimum

backsplash locator line.

Handle

Escutcheon

Calculated Faucet

Centerline Distance

2" (5.1 cm)

Min.

Backsplash

Countertop Template

Rim Outline

Centerline

2" (5.1 cm) Min.

1/4" (6 mm) Min.

Kohler Co. 3 1018896-2-C

Preparation (cont.)

NOTE: Some Kohler faucets require a minimum of 2-1/2″(6.4 cm)

behind the ﬁnal faucet centerline.

Cut along the backsplash locator line on the template.

Cut out the template along the inside of the template cutting line.

Position the template on the countertop to ensure clearance

between the lavatory, faucet, and backsplash.

Verify cabinet clearance beneath the countertop.

Use a pencil to trace the template on the countertop.

Mark the faucet and handle centerline on the countertop.

1018896-2-C 4 Kohler Co.

2. Self-Rimming Installation

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

Cut out the opening by carefully following the pencil line traced

from the template.

Temporarily position the lavatory in the countertop to check ﬁt.

Remove the lavatory.

Drill the faucet holes according to the faucet installation

instructions.

Install the faucet to the countertop according to the

manufacturer’s instructions.

Install the drain to the lavatory according to the drain

manufacturer’s instructions.

NOTE: When installing the K-7702 drain, use the tapered gasket

supplied with the lavatory instead of the gasket supplied with the

drain. CAUTION: Risk of product damage. Overtightening the wing

nuts may cause irreparable damage to the lavatory.

Apply bead of sealant around entire underside of lavatory rim

between stud and rim edge.

Place the lavatory into the cut-out hole and position.

Self-Rimming Installation

Lavatory

Sealant

Stud

Kohler Co. 5 1018896-2-C

Self-Rimming Installation (cont.)

Assemble the clip and wing nut to the stud and carefully

ﬁnger-tighten to remove any gaps between the lavatory rim and

the countertop. Do not overtighten the wing nuts.

Remove any excess sealant using damp cloth.

Allow sealant to set for 30 minutes before proceeding.

Proceed to the Complete the Installation section.

1018896-2-C 6 Kohler Co.

3. Undercounter Installation

Cut-Out Dimensions

AB C

K-2610 Round Lav. 10-1/8″(25.7

cm) 10-1/8″(25.7 cm) N/A

K-2612 Round Lav. 13-1/2″(34.3

cm) 13-1/2″(34.3 cm) N/A

K-2611 Oval Lav. 9-3/4″(24.8 cm) 11-3/4″(29.8 cm) N/A

K-2602 Elliptical 13-3/4″(34.3

cm) 12″(30.5 cm) 23-5/8″

(60 cm)

Cut out the opening by carefully following the pencil line traced

from the template.

Install Wood Countertop

Mark and pre-drill the wood screw holes at the locations shown

on the previous table.

Waterproof any exposed areas of wood.

Install Marble/Stone Countertop

Position the countertop upside down on foam padding to protect

the surface.

Wood Countertop

Lavatory

Sealant

Undercounter Installation

Marble Slab / Solid Surface

Countertop

Lavatory

Insert

Sealant

Reference Hole

Location

Kohler Co. 7 1018896-2-C

Undercounter Installation (cont.)

Mark and drill 3/8″holes 5/8″(1.6 cm) deep at the locations

shown on the previous table.

Use a setting tool and hammer to secure the anchors.

For All Undercounter Installations

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

If the countertop has not been installed, install it at this time.

Drill the faucet holes according to the faucet installation

instructions.

Install the faucet to the countertop according to the faucet

manufacturer’s instructions.

Install the drain to the lavatory according to the drain

manufacturer’s instructions.

NOTE: When installing the K-7702 drain, use the tapered gasket

supplied with the lavatory instead of the gasket supplied with the

drain.

Apply a continuous bead of quality sealant to the top surface of

the lavatory rim where it will contact the countertop.

NOTE: The screws provided should be used on countertops with a

minimum 1″(2.5 cm) thickness. For thinner countertops, use

appropriate anchors and fasteners (not provided).

For wood, wood composite, and marble countertops, install the

lavatory to the countertop with the clamps and screws provided.

For other countertop materials, refer to the countertop

manufacturer’s instructions for recommended fasteners.

CAUTION: Risk of product damage. Overtightening the nuts

may cause irreparable damage to the lavatory.

Position the lavatory squarely under the cutout before tightening

the clamps. Draw the lavatory rim up against the countertop until

it is snug. Do not overtighten.

Immediately wipe away any excess sealant, and ﬁll any voids as

needed.

Allow the sealant to set for 30 minutes before proceeding.

Proceed to the Complete the Installation section.

1018896-2-C 8 Kohler Co.

4. Complete the Installation

Assemble the adjustable drain pop-up linkage.

Apply plumbers putty to the underside of the drain ﬂange.

Insert the drain ﬂange into the drain hole of the lavatory.

From underneath the lavatory, apply plumbers putty to the

underside of the drain area.

Slide the gasket, tapered side down, followed by the chrome

plated brass tube on to the drain ﬂange.

Slide the other gasket, tapered side up, onto the drain ﬂange and

push the gaskets and tube up against the underside of the

lavatory.

Slide the ﬂat washer onto the drain ﬂange and up against the

bottom gasket.

Secure the assembly with the locknut.

Connect and tighten the trap to the drain, and complete the water

supply connections to the faucet according to the instructions

packed with the faucet.

Run water into the lavatory and check for leaks.

Clean up with a non-abrasive cleaner.

Turn the water supplies on and check for leaks.

Drain Flange

(Purchased)

Apply

plumbers

putty.

Tapered Gasket

Flat Washer

Locknut

Chrome Plated

Brass Tube

Kohler Co. 9 1018896-2-C

Guide d’Installation

Lavabos à rebord intégré/sous comptoir

Outils et matériaux

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de Commencer

AVERTISSEMENT : Risque de blessure corporelle. Les surfaces

métalliques ont des bords tranchants et peuvent provoquer de

graves coupures. Porter des gants et manipuler les rebords de

l’évier avec précaution.

Respecter tous les codes de plomberie et de bâtiment locaux.

Avant son installation, déballer le nouveau lavabo et l’examiner

pour en déceler tout dommage. Remettre le lavabo dans son

emballage de protection jusqu’à être prêt à l’installer.

Inspecter le drain et la tuyauterie d’alimentation. Remplacer si

nécessaire.

N’utiliser uniquement que le mastic fourni avec ce lavabo.

Plus:

• Mêche 1/2"

• Règle

• Scie-cloche

• Gants

Metre

ruban

Tournevis

Scie égoïne

Plan

(fourni) Crayon Perceuse Lunettes de

protection Clé à

molette

Kohler Co. Français-1 1018896-2-C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler FLIGHT NEUS E62C70-00 Bedienungsanleitung

Kohler

Kohler K-10958 Bedienungsanleitung

Kohler

Kohler GANDIDE 11685T-4 Bedienungsanleitung

Kohler

Kohler 10089W-CP Bedienungsanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler 11679T Bedienungsanleitung

Kohler

Kohler Triton Rite-Temp K-T6910-2A Bedienungsanleitung

Kohler

Kohler K-6814-3 Montageanleitung

Kohler

Kohler K-352 Bedienungsanleitung

Kohler

Kohler K-T10302 Bedienungsanleitung

Kohler

Kohler K-23984T-0 Bedienungsanleitung

Kohler

Kohler K-77681 Series Bedienungsanleitung

Kohler

Kohler K-R99252X-4CD Montageanleitung

Kohler

Kohler PATIO ECO K-18645T-Y Bedienungsanleitung

Kohler

Kohler 18464 Bedienungsanleitung

Kohler

Kohler K-3099 Bedienungsanleitung

Kohler

Kohler WaterTile K-8030 Bedienungsanleitung

Kohler

Kohler 99721T-4 Bedienungsanleitung

Kohler

Kohler TAHOE Bedienungsanleitung

Kohler

Kohler BRIVE+ K-8703IN-1WH Bedienungsanleitung

Kohler

Kohler Flipside 15704T Bedienungsanleitung

Kohler

Kohler Deerfield 5815W Bedienungsanleitung

Kohler

Kohler PureWarmth Bedienungsanleitung

Kohler

Kohler K-1257P Kurzanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung