Kohler K-T10302 Bedienungsanleitung

Installation Guide

Stacked Thermostatic Valve Trim

K-T10302, K-T10422, K-T10427,

K-T10594, K-T10941, K-T14489,

K-T16176

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1041504-2-E

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

The trim design illustrated in this guide is representative and

may differ from the actual trim being installed. Install the trim as

instructed.

Before installing the trim, determine if the maximum water

temperature is acceptable to the user. If temperature adjustment is

needed, refer to the instructions packed with your valve for

proper temperature limiting adjustment.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the price book.

Screwdrivers Hex

Wrenches

Adjustable

Wrench

1041504-2-E 2 Kohler Co.

1. Install the Valve Stem Adapter

IMPORTANT! Two screws of each length are supplied for this step,

one metric and one standard. If the screw you are using is difficult

to thread into the opening, remove it and use the other screw.

NOTE: Check the ﬁnished wall surface as related to the graphics on

the plaster guard.

Select the correct length valve stem adapter and valve stem

adapter screw for your application. Refer to the information

stamped on the plaster guard to verify the wall thickness.

For a thin wall - 3/16″(5 mm) to 9/16″(1.4 cm):use the 7/8″(2.2

cm) (short size) valve stem adapter, stamped ″3″on the plaster

guard. Use the 3/4″(1.9 cm) screw for the top valve and the 1-3/8″

(3.5 cm) screw for the lower valve.

For a standard wall - 9/16″(1.4 cm) to 1-1/16″(2.7 cm):use the

1-3/8″(3.5 cm) (middle size) valve stem adapter, stamped ″1″on the

plaster guard. Use the 1-3/8″(3.5 cm) screw for the top valve and

the 1-3/4″(4.4 cm) screw for the lower valve.

For a thick wall - 1-1/16″(2.7 cm) to 1-9/16″(4 cm):use the 1-7/8″

(4.8 cm) (long size) valve stem adapter, stamped ″2″on the plaster

guard. Use the 1-3/4″(4.4 cm) screw for the top valve and the

2-3/8″(6 cm) screw for the lower valve.

Remove and discard the plaster guard from the valve.

Select the correct

valve stem adapter.

Remove and discard

the plaster guard.

Valve Stem

Adapter

Spline

Adapter

Finished

Wall

Kohler Co. 3 1041504-2-E

Install the Valve Stem Adapter (cont.)

Place the spline adapters over the valve stems.

Set the correct valve stem adapters over each valve stem. Do not

completely press or screw the valve stem adapters into place

until instructed to do so.

1041504-2-E 4 Kohler Co.

2. Adjust the Handle Assembly

Ensure the valve stem adapters are lightly placed over the spline

adapters.

Place the handle assembly over the valve stem adapter of the

volume control valve (top).

Turn the handle assembly counterclockwise until it stops. The

volume control handle assembly should be in the vertical 12

o’clock position. This is the off position.

Remove the handle assembly and set aside.

Place the remaining handle assembly over the valve stem adapter

of the thermostatic valve (bottom).

Turn the handle assembly clockwise until the stop is contacted.

The valve will be in the full cold position. The handle should be

between the 9 and 10 o’clock positions.

Rotate the handle assembly counterclockwise, through the detent,

then to the high temperature limit stop.

Verify that the handle assembly is between the 3 and 4 o’clock

position.

Rotate back to 6 o’clock position.

Remove the handle assembly and set aside.

NOTE: The spline adapter allows ﬁne adjustment of the handle

alignment.

Valve Stem Adapter

Handle Assemblies

Thermostatic

Valve

Volume Control Valve

Kohler Co. 5 1041504-2-E

Adjust the Handle Assembly (cont.)

To adjust, remove the handle assembly and the valve stem

adapter.

Reposition the spline adapter.

Reinstall the handle assembly and the valve stem adapter.

Check the alignment.

Repeat until the handle alignment is satisfactory.

1041504-2-E 6 Kohler Co.

3. Install the Trim

NOTE: If you are installing the K-T10422 trim, proceed to the

″Install the Trim - K-T10422″section of this guide.

Firmly press the valve stem adapters onto each valve stem.

Secure the valve stem adapters to the valve with the correct

length screws, as selected in the ″Install the Valve Stem Adapters″

section of this guide.

Thread the two threaded studs into the threaded holes of the

valve.

Place the front plate assembly over the threaded studs.

NOTE: If the front plate assembly does not lay ﬂat on the wall

surface, loosen the nuts and adjust the threaded studs, then tighten

the nuts. The maximum distance between the threaded studs from

the wall is 7/16″(1.11 cm).

Visually inspect the front plate assembly to ensure that the foam

seal is completely covering the wall opening. If not, stop the

installation and repair the wall opening.

Place the escutcheon against the wall. The drain hole in the

escutcheon should face downward in the 6 o’clock position.

Thread the handle assemblies onto the hubs of the front plate

assembly to secure the escutcheon in place. The volume control

handle assembly (top) should be at the 12 o’clock position. The

thermostatic valve handle assembly (bottom) should be at the 6

o’clock position.

Thermostatic Valve

Valve Stem Adapter

Finished Wall

Front Plate Assembly

Escutcheon

Screws

Threaded Studs

Nuts

Handle Assembly

Kohler Co. 7 1041504-2-E

Install the Trim (cont.)

NOTE: If the handle does not engage the valve or the escutcheon

does not tighten to the wall, replace the valve stem adapter with an

adapter of appropriate length.

1041504-2-E 8 Kohler Co.

4. Install the Trim - K-T10422

Firmly press the valve stem adapters onto each of the valve

stems.

Secure the valve stem adapters to the valve stem with the correct

length screws, as selected in the ″Install the Valve Stem Adapters″

section of this guide.

Thread the two threaded studs into the threaded holes of the

valve.

Place the front plate assembly over the threaded studs.

NOTE: If the front plate assembly does not lay ﬂat on the wall

surface, loosen the nuts and adjust the threaded studs, then

re-tighten the nuts. The maximum distance between the threaded

studs from the wall is 7/16″(1.11 cm).

Inspect the front seal plate assembly to ensure that the foam seal

is completely covering the wall opening. If not, stop the

installation and repair the wall opening.

Place the escutcheon against the wall. The drain hole in the

escutcheon should face downward in the 6 o’clock position.

Thread the adapter rings onto the hub of the front plate assembly.

Place the handle assemblies against the escutcheon by lining up

the pins in the handle assembly with the holes in the escutcheon.

Make sure the setscrew holes are facing down.

Valve Stem Adapter

Adapter Ring

Volume Control

Setscrews

Escutcheon

Thermostatic

Valve Screw

Screw

Front Plate Assembly

Threaded Studs

Nuts

Handle

Assembly

Kohler Co. 9 1041504-2-E

Install the Trim - K-T10422 (cont.)

NOTE: The volume control handle should be at the 12 o’clock

position. The thermostatic valve handle should be at the 6 o’clock

position.

Tighten the setscrews in place with a hex wrench. Make sure the

handle assemblies are tight against the escutcheon.

1041504-2-E 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13770 Bedienungsanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler 72678M-7 Bedienungsanleitung

Kohler

Kohler Fairfax K-12185 Montageanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler KUMIN 98827IN-4/4ND Series Bedienungsanleitung

Kohler

Kohler K-7303 Bedienungsanleitung

Kohler

Kohler Stanwell K-4972 Bedienungsanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler 1007966 Handbuch

Kohler

Kohler Memoris 10435T Bedienungsanleitung

Kohler

Kohler K-3148 K-3150 Montageanleitung

Kohler

Kohler STANCE 14760A-4ND Bedienungsanleitung

Kohler

Kohler Fluence K-702221-6L Bedienungsanleitung

Kohler

Kohler Mira Jump 7.5 Bedienungsanleitung

Kohler

Kohler Clearflo K-7147 Bedienungsanleitung

Kohler

Kohler Seawall K-6504 Bedienungsanleitung

Kohler

Kohler K-T309 Bedienungsanleitung

Kohler

Kohler MAXISPACE K-77217T Bedienungsanleitung

Kohler

Kohler K-13462 Bedienungsanleitung

Kohler

Kohler K-4986X Montageanleitung

Kohler

Kohler K-5834 Montageanleitung

Kohler

Kohler K-10268 Bedienungsanleitung

Kohler

Kohler K-17230T-DR Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung