Kohler K-T16113 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

K-T16113, K-T16114, K-T16115,

K-T16116, K-T16117, K-T16139,

K-16213, K-16214, K-16217

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1025255-2-C

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1025255-2-C 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of product damage to the K-306-KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

Before installing the trim, determine if the maximum water

temperature is acceptable to the user. If temperature adjustment is

needed, refer to the ″Water Temperature Adjustment″section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″Off″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Assorted

Screwdrivers Strap

Wrench Plumbers

Putty Thread

Sealant Hex Wrench

Kohler Co. 3 1025255-2-C

1. Install the Spout

CAUTION: Risk of internal seal damage. Do not use

petroleum-based lubricants when installing slip-ﬁt spouts. If the

spout will not slide over the tubing, use soapy water or a

silicone-based lubricant.

Remove the temporary nipple.

Apply thread sealant and install a 1/2″nipple so it extends 7/16″

(1.1 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple and thread the spout onto the

nipple.

Carefully tighten with a clean strap wrench.

Remove all excess putty.

Nipple

Apply plumbers

putty.

3-7/8"

(9.8 cm)

Threaded Spouts

1025255-2-C 4 Kohler Co.

2. Install the Showerhead

CAUTION: Risk of product damage. To avoid clogging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

NOTE: A standard showerhead is shown.

Installing the Standard Showerhead

Remove the temporary nipple from the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the escutcheon according to the manufacturer’s instructions.

Slide the escutcheon over the shower arm.

Apply thread sealant tape and install the shower arm to the

shower elbow.

Carefully tighten with a clean strap wrench.

Press the escutcheon against the ﬁnished wall and secure with the

setscrew.

Remove all excess putty.

Turn the main water supply on.

Run hot and cold water through the shower arm to ﬂush out dirt

and debris.

Apply thread sealant tape to the shower arm and thread the

showerhead to the shower arm.

Apply plumbers putty.

Escutcheon

Setscrew

Standard

Shower Arm

Nonstandard

Shower Arm

Shower

Elbow

1/2"

Nipple

1/2"

Apply plumbers

putty.

Shower Arm

Showerhead

Kohler Co. 5 1025255-2-C

Install the Showerhead (cont.)

Installing the Nonstandard Showerhead

Remove the temporary nipple from the shower elbow.

Apply thread sealant tape and install a 1/2″NPT nipple to

extend 1/2″(1.3 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant to the back of

the shower arm according to the manufacturer’s instructions.

Apply thread sealant tape to the nipple and thread the shower

arm onto the nipple.

Carefully tighten with a clean strap wrench.

Remove all excess putty.

With the showerhead off, ﬂush out the system.

Apply thread sealant tape to the shower arm, and thread the

showerhead to the shower arm.

1025255-2-C 6 Kohler Co.

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

Kohler Co. 7 1025255-2-C

4. Diverter Assembly

Remove and discard the plaster guard and/or dome, if installed.

Position the actuator over the diverter stem. Tighten the setscrew.

Slide the guide over the actuator and thread it onto the diverter

stem.

Guide

Setscrew

Actuator

Diverter Assembly

Valve

Stem

Diverter

Stem

Discard plaster

guard with dome.

1025255-2-C 8 Kohler Co.

5. Install the Faceplate and Handle

CAUTION: Risk of product damage to the K-306-KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Remove and discard the plaster guard and/or dome, if installed.

Rotate the valve stem fully counterclockwise to the ″Off″position.

Install the faceplate onto the valve. Secure with two screws. Do

not overtighten.

Slide the sleeve over the valve stem with the slot down and

facing outward.

Scroll Handle

Install the handle to the base.

Secure with a screw.

Align the handle assembly and press it onto the valve stem.

Secure the handle in place with the setscrew. Tighten the setscrew

to one quarter-turn past hand-tight.

Traditional Handle

Assemble the handle and bonnet.

Install the washer and O-ring onto the base.

Fit the handle assembly to the base.

Secure with a screw.

Faceplate

Sleeve

Slot

Valve Stem

Screw

Discard plaster

guard with dome.

Faceplate

Washer

O-Ring

Bonnet

Screw

Base

Setscrew Traditional

Handle

Scroll

Handle

Kohler Co. 9 1025255-2-C

Install the Faceplate and Handle (cont.)

Align the handle and the base assembly. Press the handle onto the

valve stem.

Secure the handle in place with the setscrew. Tighten the setscrew

to one quarter-turn past hand-tight.

6. Complete the Installation

Turn the valve fully counterclockwise to the off position.

Remove the aerator assembly from the spout by turning it

counterclockwise.

Turn on the main water supply.

Turn the valve to the center and run water for approximately one

minute to ﬂush the system.

Check all connections for leaks.

Reinstall the aerator.

1025255-2-C 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Finial 607T Bedienungsanleitung

Kohler

Kohler Purist 7505D Bedienungsanleitung

Kohler

Kohler 22327T-7 Bedienungsanleitung

Kohler

Kohler 1145707 Bedienungsanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler K-4177 Bedienungsanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler 84625 Handbuch

Kohler

Kohler Kumin K-104K36-SANA-CP Bedienungsanleitung

Kohler

Kohler REVIVAL K-T16119 Bedienungsanleitung

Kohler

Kohler FOLIO K-2017IN-1 Bedienungsanleitung

Kohler

Kohler COUTURE ECO-LITE Bedienungsanleitung

Kohler

Kohler 10415T-B Bedienungsanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler RUBICON 20147T-4 Bedienungsanleitung

Kohler

Kohler Family Care 2.0 K-701646T-FM-SHP Bedienungsanleitung

Kohler

Kohler Deerfield 5815W Bedienungsanleitung

Kohler

Kohler Cabriole K-T14641 Montageanleitung

Kohler

Kohler 1152813-A2-A Bedienungsanleitung

Kohler

Kohler K-7323 Bedienungsanleitung

Kohler

Kohler K-6350 Bedienungsanleitung

Kohler

Kohler K-T9493 Bedienungsanleitung

Kohler

Kohler K-7166-AF Montageanleitung

Kohler

Kohler Primary K-4321 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung