Kohler 8002A Bedienungsanleitung

11067580-AN2-E 17/02/12

IMPORTANT

INSTALLER: THIS MANUAL IS THE PROPERTY OF THE

CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT

FOR MAINTENANCE AND OPERATIONAL PURPOSES.

Installation and User Guide

Watertile Bodyspray

MODEL NUMBERS

Important! Please quote the above model number(s) when ordering spares

8002A, 8003A

1067580-AN2-E 17/02/12

SPECIFICATION

DIMENSIONS

8003A

8002A

G 1/2"

124 mm

89 mm

79 mm Min Clearance

67 mm

60 mm

Center of

Water Inlet

All information is based on the latest product information available at the time

of publication. Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time without notice.

Please leave these instructions for the consumer.

NOTES:

1. Flush the water supply pipes thoroughly to remove any debris.

2. An in line water filter must be used with this product.

3. Inspect the supply pipes for damage. Replace as necessary.

4. Observe local plumbing codes.

5. The recommended working pressure for the shower head is 150KPa to

500KPa. If the pressure exceeds 500KPa a pressure reducer is required.

6. Maximum water and environmental temperature for the shower head is

60C. Note: If a heater is present, make sure to keep it away from the shower

head as otherwise the environmental temperature may exceed 60C.

7. All installations should comply with the relevant requirements of AS/NZS

3500 and AS/NZS 6400.

BEFORE YOU BEGIN

Pressures

For multiple outlets an operating pressure of 3.0 bar or greater is

recommended to ensure optimum performance.

Plumbing Connections

(Hot) and Cold (C) inlets must be connected to the

correct inlet supplies.

Building in Depth

Minimum building in depth is 79 mm. It is recommended that

a minimum stud wall cavity of 100 mm is provided to ease installation.

31067580-AN2-E 17/02/12

INSTALLATION

Install the Supply Pipes

Single Bodyspray Installations

1. Install the water supply pipes. Do not

ﬁx the pipework at this time.

2. Install an elbow to the end of the supply

pipe at the bodyspray installation

location.

Multiple Bodyspray Installations

1. Install the water supply pipes. Do not

ﬁx the pipework at this time.

2. If installing more than one bodyspray

off the same supply line, construct

a pressure balancing loop. Locate a

tee along the loop at each bodyspray

installation location.

For All Installations

1. Temporarily install the nipple (supplied

toeach tee/elbow. Donot use any

sealant.

Install the Plaster Guard

1. Fix the wall elbow or tee to the back of

the supporting structure.

2. Install the plater guard against the face

of the elbow or tee.

Important! make sure that there

is sufficient building-in depth. The

minimumdimension from the back of

the wall elbow to the front face of the

ﬁnished wall (including tile thickness) is

79 mm.

Before you Begin

1. Turn off the water supply.

2. Kohler Co. reserves the right tomake revisions in the design of products without

notice.

Single Bodyspray Installation

Multiple Bodyspray Installation

Nipple

Pressure

Balancing Loop

Water

Supply Pipe

Elbow (or Tee)

Install the Plaster Guard

Plaster Guard

1067580-AN2-E 17/02/12

Install the Finished Wall

1. Finish the wall, leaving the cutout 102

to 108 mm square.

2. Make sure that the dimension from the

front face of the elbow or tee to the

surface of the ﬁnished wall is a minimum

of 57 mm.

3. Thread the nipple into the elbow or tee

and hand tighten.

4. Measure the distance from the end of

the nipple to the surface of the ﬁnished

wall. Make sure that it is between 38

and 44 mm. If necessary cut the nipple

to the required length.

5. Remove the nipple and apply thread

sealant to the ends of the nipple.

6. Reinstall the nipple to the elbow or

tee.

7. Turn obn the water supply and ﬂush out

the supply pipes.

Install the Waterway

1. Install the concealing plate into the

rough opening. The double ribs of the

leak shield should be facing up.

2. If the leak shield makes contact with the

elbow enlarge the hole in the back of the

leak shield to 32 mm.

3. Thread the adapter onto the nipple using

a 7/16” hexagonal wrench.

Important! The concealing plate should

ﬁt loosely at this point.

4. Align the groove in the waterway with

the double ribs on the leak shield.

5. Press the waterway into place over the

adapter.

6. Secure the waterway to the adapter with

the screw provided.

7. Make sure that the concealing plate

does not turn and is not loose.

Important! If the concealing plate is still

loose at this point shorten the nipple.

102 to 108 mm

Cutout

Nipple

Tee (or Elbow)

Finished Wall

Cutout

57 mm Min

7/16" Hex Wrench

Leak Shield

Concealing Plate

Adapter

Waterway

Screw

51067580-AN2-E 17/02/12

Finish the Installation

1. With the ribs of the sprayhead facing up,

attach the sprayhead to the waterway.

2. Using a 3/16” hexagonal wrench, fit

the sprayhead to the waterway with the

two securing screws (supplied). Do not

overtighten.

3. Check the sprayhead for upward and

downward movement and that is sits

squarely within the concealing plate.

4. Place the nozzle membrane over the

sprayhead.

5. Align the long edge of the membrane

with the hinge ribs (horizontal).

Note! For optimum performance make

sure that the membrane is applied

evenly.

6. Applying pressure evenly, press the

membrane seal into the sprayhead

groove.

7. Tilt the sprayhead downward so the ribs

on top of the sprayhead are exposed.

8. Insert the grooves of the sprayface over

the ribs of the sprayhead.

9. Press the sprayface down to cover the

sprayhead, as illustrated.

10. Tilt the sprayhead upwards to expose

the setscrew holes on the bottom of the

sprayhead.

Important! The setscrews must be ﬂush

with the edge of the sprayface frame. If

the setscrews protrude outside of the

sprayface frame, product damage will

occur.

11. Using a 5/64” hexagonal wrench, turn

the setscrews anti-clockwise until they

are ﬂush with the edge of the sprayface

frame.

Sprayface

Ribs

Groove

Finished Wall

Setscrews

Sprayhead

Waterway

Securing Screws

Attach the Sprayhead

Nozzle

Membrane

Attach the Sprayface

1067580-AN2-E 17/02/12

SPARE PARTS

3007215

Screen Washer

1040636

Flow Restrictor

1036043

Shield

1055233

Adapter

1045771**

Concealing Plate

1051498

Nipple G1/2

1044060

O-Ring

**Finish/color code must be specified when ordering.

1044058

O-Ring

1044059

O-Ring

1047041

Washer

1040637

Screw

1036040

Spacer

1056104

Spring Washer

1036038

Screw

1041362

Wire

1045773

Base

(Includes

Clamps)

1079599

Grommet

1067580-AN2-E 17/02/12

Like anything of lasting quality, Kohler tapware and ﬁttings require a certain amount of periodic care to

preserve their lustrous ﬁnish. Clean your new Kohler tapware and ﬁttings with a mild soap, rinse thoroughly

with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any

water from metal surfaces.

Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to

dry metal, not an abrasive or rubbing action.

Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, or chemicals that can damage

the ﬁnish. By taking the time to dry your tapware often, soap and water deposits can be prevented.

Failure to comply with these cleaning instructions may void Kohler’s warranty obligations.

CARE AND CLEANING

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler NEW MEMOIRS K-76555T Bedienungsanleitung

Kohler

Kohler C3-130 Bedienungsanleitung

Kohler

Kohler K-1997 Montageanleitung

Kohler

Kohler K-14660 Montageanleitung

Kohler

Kohler 10373 Bedienungsanleitung

Kohler

Kohler Cachet Quiet-Close K-7671 Bedienungsanleitung

Kohler

Kohler 6625-0 Bedienungsanleitung

Kohler

Kohler COUTURE ECO-LITE Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic 9.8kW 1.1746.006 Bedienungsanleitung

Kohler

Kohler K-11550 Montageanleitung

Kohler

Kohler ARCHER K-2595-GW Bedienungsanleitung

Kohler

Kohler K-T13140 Bedienungsanleitung

Kohler

Kohler MINIMA K-45805T Bedienungsanleitung

Kohler

Kohler PURIST UPGRADE Bedienungsanleitung

Kohler

Kohler K-7179 Montageanleitung

Kohler

Kohler MINIMA K-45803T-L-SHP Bedienungsanleitung

Kohler

Kohler STERLING 5300 Series Montageanleitung

Kohler

Kohler K-3393 Montageanleitung

Kohler

Kohler July 16027 Bedienungsanleitung

Kohler

Kohler K-T15601 Bedienungsanleitung

Kohler

Kohler Mira Evoco Series Bedienungsanleitung

Kohler

Kohler K-7259 Montageanleitung

Kohler

Kohler K-922 Bedienungsanleitung

Kohler

Kohler K-T16229 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung