Kohler K-T6808 Bedienungsanleitung

Installation Guide

Bath and Shower Faucet Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T6808 K-T6809

K-T6810 K-6812

114498-2-E

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

114498-2-E 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

We recommend that you determine if the maximum water

temperature is acceptable before installing this trim. If

temperature adjustment is needed, refer to the ″Water

Temperature Adjustment″section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″Off″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Thermometer

Strap

Wrench Thread

Sealant

Plumbers

Putty Hex

Wrench

Assorted

Screwdrivers

Kohler Co. 3 114498-2-E

1. Install the Spout

Remove the temporary nipple.

For the 4-7/8″(12.4 cm) diverter spout: Apply thread sealant to a

1/2″NPT nipple and install it to the bath elbow so it extends

7/16″(1.1 cm) beyond the ﬁnished wall.

For the 7-3/4″(19.7 cm) diverter spout: Apply thread sealant to a

1/2″NPT nipple and install it to the bath elbow so it extends

1/2″(1.3 cm) beyond the ﬁnished wall.

For the 7-3/4″(19.7 cm) non-diverter spout: Apply thread sealant

to a 1/2″NPT nipple and install it to the bath elbow so it extends

6-1/4″(15.9 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple, and install the spout to the

nipple.

Carefully tighten with a clean strap wrench.

Remove excess putty.

1/2" Nipple 1/2" Nipple

1/2" Nipple

7/16"

(1.1 cm) 1/2"

(1.3 cm)

6-1/4"

(15.9 cm)

Apply

plumbers

putty.

4-7/8" (12.4 cm)

Spout

7-3/4" (19.7 cm)

Non-Diverter

Spout

7-3/4" (19.7 cm)

Diverter Spout

Apply plumbers putty.

114498-2-E 4 Kohler Co.

2. Install Shower Arm and Showerhead

Remove the temporary nipple from the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the escutcheon according to the manufacturer’s instructions.

Install the O-ring and sleeve to the escutcheon.

Slide the collar, sleeve, and escutcheon onto the shower arm.

Apply thread sealant tape and install the shower arm to the

shower elbow.

Carefully tighten with a clean strap wrench.

Press the escutcheon and sleeve against the ﬁnished wall.

Slide the collar tight against the sleeve and escutcheon, and

secure with the setscrew.

Remove all excess putty.

Flush out the system.

Apply thread sealant tape to the shower arm and thread the

showerhead to the shower arm.

Shower Elbow

Shower Arm

Collar

Sleeve

Setscrew

Escutcheon

O-Ring

Showerhead

Apply plumbers putty

to escutcheon.

Kohler Co. 5 114498-2-E

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

114498-2-E 6 Kohler Co.

4. Install the Faceplate and Lever Handle

CAUTION: Risk of product damage to the K-306–KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Remove and discard the plaster guard and/or dome, if installed.

Fit the faceplate and centering washer over the valve, and secure

with two screws.

Rotate the valve stem fully counterclockwise.

Lever Handle

Fit a sleeve and bonnet over each stem adapter.

Thread a bonnet to each valve body until they are tight against

the escutcheon.

Install a center cap to each bonnet.

Fit a long sleeve to each handle arm, and secure it with the end

cap.

Insert a handle arm through each center cap and bonnet.

Install a short sleeve and washer onto each handle arm and

secure them with the end cap.

Valve Stem

Faceplate

Screws

Centering Washer

Discard plaster

guard with dome.

Valve Stem

Short Sleeve

Handle Arm

Long Sleeve

O-Ring

Bonnet

Sleeve

Screw

Washer

End Cap

Center Cap

Kohler Co. 7 114498-2-E

5. Installing Other Handle Styles

Cross Handle

Install the sleeve and bonnet to the valve stem.

Align the bonnet and secure to the valve stem with the screw.

Fit the center cap to the bonnet so the holes align.

Insert the long arm into the large holes in the center cap so the

holes align.

Insert the long and short studs into the remaining center cap

holes and securely thread together.

Insert the O-rings, sleeves, washers, and end caps to the handle

ends.

Valve Stem

Short

Stud

Long Stud

O-Ring

(4 Places) Sleeve

Sleeve

Washer

End Cap

Sleeve

BonnetScrew Center Cap

Long Arm

114498-2-E 8 Kohler Co.

Guide d’installation

Garniture de robinet de baignoire et de

douche

INSTRUCTIONS IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou de blessures graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition de débit

croisé au régulateur et modiﬁer la température de l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements de température d’eau saisonniers,

et le remplacement ou l’entretien du chauffeau, changeront la

température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures.

•La valve à pression équilibréene compensera pas les changements

de température d’alimentation d’eau; ajuster la température

maximale de cette valve à pression équilibrée si de tels

changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de cette valve selon les

instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

Kohler Co. Français-1 114498-2-E

INSTRUCTIONS IMPORTANTES (cont.)

AVIS IMPORTANT AUX INSTALLATEURS! Veuillez remplir le

coupon dans le guide du propriétaire ainsi que sur l’étiquette de la

valve. Conserver le guide du propriétaire pour future référence.

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Le mur ﬁni ou la baignoire/douche doit être installé avant

d’installer cette garniture.

Nous conseillons de déterminer si la température maximale de

l’eau est acceptable avant d’installer la garniture. S’il un réglage

de température est nécessaire, se réferer à la section ″Réglage de

la température d’eau″.

La valve s’arrête par pression d’eau. Ne pas forcer la poignée

dans aucune direction. Pour fermer la poignée, la tourner

doucement sur la position ″Off″.

Couper l’alimentation d’eau principale.

Thermomètre

Clé à

sangle Joint

d'étanchéité

pour filetage

Mastic de

plombier Clé

hexagonale

Tournevis

assortis

114498-2-E Français-2 Kohler Co.

Andere Handbücher für K-T6808

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Cabriole K-T14641 Montageanleitung

Kohler

Kohler K-5414 Betriebsanleitung

Kohler

Kohler K-7273-AF Montageanleitung

Kohler

Kohler K-4986X Montageanleitung

Kohler

Kohler K-7129 Montageanleitung

Kohler

Kohler WaterTile K-8030 Montageanleitung

Kohler

Kohler K-T10274 Montageanleitung

Kohler

Kohler TAUT 73194T-4E2 Bedienungsanleitung

Kohler

Kohler LOURE K-98452T-NW-CP Bedienungsanleitung

Kohler

Kohler Archer K-2359 Bedienungsanleitung

Kohler

Kohler K-1630-L Bedienungsanleitung

Kohler

Kohler KARAT K-23883 Bedienungsanleitung

Kohler

Kohler MODULO 72801T-4 Bedienungsanleitung

Kohler

Kohler Sunstruck K-24009-GHW Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-1107 Bedienungsanleitung

Kohler

Kohler K-T14419 Montageanleitung

Kohler

Kohler MINIMA K-45805T Bedienungsanleitung

Kohler

Kohler SYMBOL 72640X Bedienungsanleitung

Kohler

Kohler K-10121 Bedienungsanleitung

Kohler

Kohler 72218T-B7-CP Montageanleitung

Kohler

Kohler K-11830 Bedienungsanleitung

Kohler

Kohler K-19480 Bedienungsanleitung

Kohler

Kohler 72419IN Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung