Kohler K-11830 Bedienungsanleitung

Installation Guide

Wall-Mount Lavatory Faucet Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-11830, K-11831

1080064-2-A

Tools and Materials

Before You Begin

NOTE: Follow the installation dimensions precisely as there is no

deep rough-in kit available for this product.

Observe all local plumbing and building codes.

Shut off the main water supply.

Inspect the supply tubing for damage. Replace as necessary.

Site preparation and wall ﬁnishing may require additional tools

and materials.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable Wrench Sealant Tape

Hex WrenchsAssorted Screwdrivers

Plus:

• Wire fasteners

• Woodworking tools

• Pipe fitting tools

• Wood Screws

• 2x4s

1080064-2-A 2 Kohler Co.

1. Prepare the Site

NOTE: The wall plate requires special framing and support

considerations. Pay special attention to minimum and maximum

faucet height recommendations noted in the roughing-in sheet.

Refer to the roughing-in dimensions for additional mounting

information.

A suggested framing example is shown. Each installation may

have different framing requirements than those shown.

Mount the control box on the wall below the lavatory or

countertop.

Construct the framing for your installation.

2. Attach the Wall Plate

NOTE: Make sure the location of the wall plate is correct before

securing it in place. The centerline of the drain and faucet should be

in line with each other.

Secure the wall plate to the studs using six wood screws (not

provided).

Finished Wall

7/8" (2.2 cm) Min

1-7/8" (4.8 cm) Max

1-7/16" (3.7 cm) Min

2-7/16" (6.2 cm) Max

16"

(40.6 cm)

2x4 Stud Framing

Wall Plate

7" (17.8 cm)

Screws

Vessel Height

Six Round Holes (Typical)

1-3/8"

(3.5 cm)

1-5/8"

(4.1 cm)

2-3/4" (7 cm) for Standard

Installations

4-1/4" (10.8 cm) for

Installations with Stainless

Steel Vessel Lavatories

Kohler Co. 3 1080064-2-A

3. Install the Suppy Pipe and Sensor Wire

Install 1/2″supply pipe to the valve assembly.

At the point where the supply will exit the wall, install a drop ear

ell ﬂush or slightly behind the ﬁnished wall.

Feed the sensor wire through the sensor mount and plaster

guard, leaving 1-1/2″(3.8 cm) minimum of exposed wire hanging

out.

Connect the sensor wire harness to the wall.

Temporarily connect the water supply to the supply ell.

Turn on the water.

Check the system for leaks.

4. Finish the Wall

Install the ﬁnished wall.

Make sure holes are created for the sensor wire harness. Location

is optional.

The diameter of the sensor hole cutout is 1-3/8″(3.5 cm).

Secure wire

harness to the wall.

Plaster Guard

Ell

1-1/2"

(3.8 cm)

1080064-2-A 4 Kohler Co.

Finish the Wall (cont.)

The diameter of the faucet hole cutout is 1-3/4″(4.4 cm).

The diameter of the wire outlet to control box cutout is 1/2″(1.3

cm).

The diameter of the supply inlet opening is determined by the ell

diameter.

Kohler Co. 5 1080064-2-A

5. Install the Sensor

Install the Bezel

Loosen the screws in the plasterguard.

Remove the plasterguard and discard.

Feed the wiring harness through the back of the bezel.

Position the bezel over the screw heads and turn 1/8 turn

counterclockwise.

Tighten the screws.

Connect the Sensor

Connect the sensor to the wire harness and feed the wire into the

wall.

Position the sensor in front of the bezel with wire on the back of

the sensor to the right.

Push the sensor into place.

Discard the

plasterguard.

Bezel

Sensor Wire

1080064-2-A 6 Kohler Co.

6. Install the Supplies

NOTE: Do not connect the control box wiring in this step.

Remove the control box cover. Make sure to keep the screws and

cover.

Mark the location of the screws using the control box as a

template. Make sure the wire harness hole in the wall is covered

by the box.

Install appropriate wall anchors (not provided) at the marks.

Feed the wires through the back of the valve and control box.

Attach the valve and control box to the wall with two screws (not

provided).

Control Box

Screws

Kohler Co. 7 1080064-2-A

7. Install the Control Box

IMPORTANT! It is critical that the inlet and outlet holes be aligned

correctly. The inlet hole is round, the outlet hole is hex shaped.

There is a sticker on the inlet side identifying it.

Slide the escutcheon over the elbow and attach the elbow to the

ell.

Slide the escutcheon tight against the wall.

Attach one end of the hose to the elbow and attach the other end

of the hose to the control box outlet.

Attach the supply hose to the control box inlet.

Attach the other end of the line to the supply stop or thermostatic

valve (recommended).

Outlet

Ell

Hex Hole

Round Hole

Inlet

Outlet

Inlet

1080064-2-A 8 Kohler Co.

8. Complete the Installation

NOTE: Avoid the area in front of the sensor for two minutes after

connections are complete. Sensor will not function correctly if it is

triggered in the ﬁrst two minutes. Disconnect and reconnect the

power to reset the sensor.

Connect the solenoid wires (green and red).

Connect the battery wires (black and orange).

Avoid the area in front of the sensor for two minutes.

Install the faucet trim following the directions provided.

Turn the water on.

Test the faucet.

Check for leaks.

Orange and

Black Battery

Wires

Green and Red

Solenoid Wires

Kohler Co. 9 1080064-2-A

Guide d’installation

Robinets infra-rouge de lavabo à montage

mural

Outils et matériels

Avant de commencer

REMARQUE : Respecter avec précision les dimensions d’installation

sachant qu’il n’y a pas de kit de raccordement pour ce produit.

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Inspecter si la tuyauterie d’alimentation est endommagée.

Remplacer si nécessaire.

Des outils et matériels additionnels pourraient être nécessaires

pour la préparation du site et la ﬁnition du mur.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Clé à molette Ruban d'étanchéité

Clés hexagonalesTournevis assortis

Plus:

• Fixations câble

• Outils de travail du bois

• Outils de raccord de

tuyau

• Vis à bois

• 2x4s

Kohler Co. Français-1 1080064-2-A

Andere Handbücher für K-11830

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-2363X Montageanleitung

Kohler

Kohler Kathryn K-2322 Montageanleitung

Kohler

Kohler 8022A Bedienungsanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler 30440 Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.0 kW Bedienungsanleitung

Kohler

Kohler Kelston 99032T-4 Bedienungsanleitung

Kohler

Kohler Soleo 8690 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Kohler

Kohler MOXIE 99107T Bedienungsanleitung

Kohler

Kohler K-10958 Bedienungsanleitung

Kohler

Kohler K-5664 Montageanleitung

Kohler

Kohler Purist 7505D Bedienungsanleitung

Kohler

Kohler HARTLAND K-11021T-1S Bedienungsanleitung

Kohler

Kohler K-6130 Montageanleitung

Kohler

Kohler K-16010-2 Bedienungsanleitung

Kohler

Kohler K-13462 Bedienungsanleitung

Kohler

Kohler K-9530 Montageanleitung

Kohler

Kohler C3-150 Montageanleitung

Kohler

Kohler K-9677 Montageanleitung

Kohler

Kohler Mira Event XS Bedienungsanleitung

Kohler

Kohler PureWarmth Bedienungsanleitung

Kohler

Kohler K-4108 Bedienungsanleitung

Kohler

Kohler K-T309 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung