Kohler MATTIA K-36971T Bedienungsanleitung

13-1 528437

INSTALLATION INSTRUCTIONS

PIVOT DOOR, L-SHAPE

K-36971T

MATTIA

-1-

, 2010

BEFORE YOU BEGINBEFORE YOU BEGIN

(

) 50~80mm

3mm/m

Before you install your shower door, please read

these instructions carefully to familiarize yourself

with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information is based on the latest product

information available at the time of publication.

Kohler China Ltd. reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning,

and warranty information-

Make sure that the bath and the finished wall

material are completely and correctly installed prior

to installing your shower door. Prepare waterproof

layer to wall and floor of the showering area. It is not

allowed for any presence of electric switches and

sockets. Make sure the floor drain runs smoothly.

Before starting the door installation, lay out and

identify all the parts. Use the exploded view

illustrated on page 2 for reference.

For the installation method of customized shower

with different dimensions, please refer to this

instructions.

Tempered glass cannot be cut, drilled or knocked

by hard object. Make sure corner area of the

glass refraining from knocking so as to cause

personal injury due to broken glass.

Please install this door on Kohler

receptors or curbs. (Not included). If the curb is not

Kohler-branded, please note its top width should fall

within the range of 50~80mm.

The shower door requires a flat vertical

finished wall. The squareness of the wall is

recommended no more than 3 mm/m. KOHLER

Company won t take responsibility of the installation

quality.

please leave these

instructions for the consumer.

CAUTION: Risk of injury or product damage.

ATTENTION:

IMPORTANT:

1120770-T01-C

-2-

ROUGHING-IN

PARTS IDENTIFICATIONPARTS IDENTIFICATION

Unit: mm

SKU BCH

K-36971T 900-1000 700-1000 1870-2000

C15

B15

Sealing Strip

Cover Strip

Side Panel

Wall Channel

Door Panel Assembly

Track

1120770-T01-C

-3-

Phillips Screwdriver

Pencil

Caulk Gun

Measuring Tape

Safety Glasses

Center Punch

Hammer

Knife

Masonry Drill & 6mm Drilll Bit

Level

Materials Required

Drop Cloth

Tape

Silicone Sealant

Tools Required

6mm

INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS

Top Caps

Splashguard

Door Handle

Assembly

Spacer

4mm Allen Key

4mm

3mm Allen Key

3mm

X6 X6

Glass Fixing Clamp

Fixing Bolt

Glass Fixing Cover

Spacer

Cover

Cover Cap

1120770-T01-C

Mark the wall 20mm in from the

front edge of the tray on both

sides.

20mm

INSTALLATION

STEP

IMPORTANT:

MUSTTray be level

along front edge.

-4-

6mm

0mm

STEP

DOOR SIDE: Fit the door wall channel to the wall.

Wall channel

vertical on

the front face.

MUST

NOTE

LH version shown. RH fitting is a mirror image of these instructions.

DOOR SIDE

The door must be

installed with the pivot

by the wall, not the

side panel.

IMPORTANT

Tray must be level in all planes

or door will not install properly.

0mm

Angled section

faces the inside

of the enclosure.

Door Side:

Fit the top and bottom tracks to the wall jamb.

Once fitted ensure structure is supported at all times.

IMPORTANT:

The flat section

of track should

face upwards at

the top and

face down at

the bottom.

Top

Bottom

1120770-T01-C

Caution

-5-

STEP

Carefully lift the door assembly into place.

The line on the wall

jamb marks the

maximum amount of

adjustment.

When fitted this line

visible outside the

wall channel.

MUST NOT

6mm

0mm

Fit the panel wall channel to the wall.

STEP

Note:

Fixing block must be on the

inside edge of the wall

channel.

Wall channel

vertical on

front face.

MUST

PANEL SIDE

For wet room fitting mark distance from back as

door side minus 11mm.

11mm

Mark the wall 20mm in from the front edge of the

tray on both sides.

20mm

1120770-T01-C

Caution

3mm

6mm

Place the 3mm section into the base of the wall

channel.

3mm

Break one spacer in half.

STEP

-6-

Have a person stand inside the enclosure.

Carefully lift the panel into place.

STEP

Carefully slide the panel into the wall channel.

Engage the mouldings but do not lock into place at

this moment.

STEP

Fix the panel to the door at top and bottom.

Note: The holes in the glass are larger than the

mounting blocks. Centre the glass on blocks when

fitting.

STEP

Note:

Assembly is

aided by tilting

the panel and

moving the fixing

blocks up or

down in the wall

Channel.

30mm Max

30mm

1120770-T01-C

Check that the door and panel are far enough into

the wall channels to lock securely (See Step 9).

Adjust if required.

Lock the panel into the wall channel by turning the

cam through 90 .

Remove the pivot base of the top track.

Locked position

STEP

-7-

STEP

Lift the door into place. Locate the bottom pivot pin

into the collar, the insert into the pivot base.

Ensure the door is fully supported at all times.

IMPORTANT:

Fit the pivot base into the top pivot pin, and tighten it

onto the top track with the screws.

IMPORTANT:

Ensure the door is fully supported at all times.

Caution

1120770-T01-C

STEP

Fit splashguards to the underside of the door.

The splashguard lip should face inside the enclosure.

-8-

STEP

Fix pivot cap onto both sides of the pivot, then knock

with rubber hammer to ensure the cap is locked in

position if necessary.

On the door side turn the adjusters through 90 to lock

the door assembly to the wall channel.

Unlocked Locked

3mm

3mm A

If the tray has been fitted level the gap under the

glass panel should be 3mm along its length and the

bottom track should be on the tray.

3mm

The position of the door can be

adjusted by loosening the fixing

screws 'A' and undoing the locks in the

wall channels. The whole assembly

can be moved to the correct position.

Tighten the screws and wall channel

locks when adjustment is complete.

1120770-T01-C

Fit the top caps.

Note:

If the glass is higher

than the wall channel,

trim away the

recessed section of

the top cap.

When the door is closed the magnetic

strips should touch along their length.

Fit the seals to the side of the door and the side of

the panel.

Fit the cover strip to the panel wall channel.

Start at the bottom and tap into place with a block of

wood or similar.

STEP

-9-

STEP

Fit the cover strip to the wall jamb.

Note:

The cover strip may need cutting to the correct length,

but do not stretch when fitting.

Glass should touch strip

when door is closed.

1120770-T01-C

Fit the door handle.

24hrs

Do not use the enclosure for at least 24 hours.

-10-

Slide the covers over the glass fixing clamps top and

bottom.

STEP

Lay a thin bead of sealant between wall channel and

wall on both sides.

Lay a thin bead of sealant along the bottom of track

and fill the gap between the glass and tray on the

outside of the enclosure.

1120770-T01-C

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler K-13711 Bedienungsanleitung

Kohler

Kohler 1083258 Handbuch

Kohler

Kohler Mira Logic L19B Bedienungsanleitung

Kohler

Kohler K-14402 Bedienungsanleitung

Kohler

Kohler EOLIA 8623T-B Bedienungsanleitung

Kohler

Kohler Memoris 10435T Bedienungsanleitung

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler K-T13133 Bedienungsanleitung

Kohler

Kohler K-3607 Montageanleitung

Kohler

Kohler STILLNESS Bedienungsanleitung

Kohler

Kohler OnCue Plus RDC Bedienungsanleitung

Kohler

Kohler K-205 Montageanleitung

Kohler

Kohler K-14620 Montageanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler K-2749 Series Montageanleitung

Kohler

Kohler RUBICON 20147T-4 Bedienungsanleitung

Kohler

Kohler REGATTA drop in 11303A-GAB-0 Bedienungsanleitung

Kohler

Kohler BodySpa K-1030 Bedienungsanleitung

Kohler

Kohler STERLING 5300 Series Montageanleitung

Kohler

Kohler K-T16237 Bedienungsanleitung

Kohler

Kohler K-7131 Montageanleitung

Kohler

Kohler K-15182 Montageanleitung

Kohler

Kohler K-13700 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung