Kohler Mira Azora Bedienungsanleitung

These instructions must be left with the user

Installation and User Guide

Mira Azora

9.8 kW

For SPARES, ADVICE

or REPAIRS

Please call us on

0844 571 5000

(UK Only)

INTRODUCTION

Thank you for purchasing a quality Mira product. To enjoy the full potential of your

new product, please take time to read this guide thoroughly. Having done so, keep

it handy for future reference.

The Mira Azora is a thermostatic electric shower with separate controls for power

selection and temperature/ow adjustment. A unique thermostatic valve stabilises

temperature changes caused by water pressure uctuations. These can result from

taps being turned on or off, or a toilet being ushed. An individual light indicates

“START/STOP”.

The Mira Azora comes complete with a set of Mira Energise Shower Fittings.

Mira Azora 9.8 kW

A 9.8 kW 240 V AC (9.0 kW 230 V AC) heater with Mira Energise adjustable spray

handset with four different spray actions (start, soothe, force and eco*). Supplied

complete with exible hose, clamp bracket assembly, slide bar, supports, hose

retaining ring and soap dish.

* The ‘eco’ setting will have no effect, and will give the same spray action as the

‘start’ setting.

Guarantee

For domestic installations, Mira Showers guarantee the Mira Azora 9.8 kW against

any defect in materials or workmanship for a period of two years from the date of

purchase (shower ttings for one year).

For non-domestic installations, Mira Showers guarantee the Mira Azora 9.8 kW

against any defect in materials or workmanship for a period of one year from the

date of purchase.

For terms and conditions refer to section “Customer Services”.

If you experience any difculty with the installation or operation of your new Electric

Shower, please refer to ‘Fault Diagnosis’, before contacting Kohler Mira Ltd.

Our telephone and fax numbers can be found in the back of this guide.

Design Registration: 000578463-001-002

Patents: GB: 2 341 667, 2 404 000, 2 428 286, 2 427 460

Ireland: 82835, 85128, 85163

Patents and Design Registration

IMPORTANT SAFETY INFORMATION

WARNING - This shower can deliver scalding temperatures if not operated,

installed or maintained in accordance with the instructions, warnings and

cautions contained in this guide and on or inside the appliance.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. Installation of this shower must be carried out in accordance with these

instructions by qualied, competent personnel.

2. Isolate the electrical and water supplies before commencing installation. The

electricity must be isolated at the consumer unit and the appropriate circuit

fuse removed, if applicable. Mains connections are exposed when the cover

is removed.

3. DO NOT install the shower in areas with high humidity and temperature

(i.e. steam rooms and saunas).

4. DO NOT install the shower where it may be exposed to freezing conditions.

Ensure that any pipework that could become frozen is properly insulated.

5. DO NOT switch the shower on if there is a possibility that the water in the

shower is frozen.

6. DO NOT switch the shower on if water starts leaking from the shower case.

Isolate the electrical supply to the shower immediately.

7. DO NOT connect the outlet of the shower to any tap, control valve, trigger

handset or showerhead other than those specied for use with this shower -

scalding water temperatures and product damage will occur. Only Kohler Mira

recommended accessories should be used.

8. The water supplies to this product must be isolated if the product is not to be

used for a long period of time. If the product or pipework is at risk of freezing

during this period they should also be drained of water.

9. DO NOT perform any unspecied modications to the shower or it’s accessories.

When servicing only use Genuine Kohler Mira replacement parts.

10. If the shower is dismantled during installation or servicing then upon completion

the product must be inspected to ensure all electrical connections are tight and

that there are no leaks.

11. Read all installation instructions before installing this shower.

12. Upon completion of the installation, make sure that the user is familiar with the

operation of the shower, and leave this guide with the owner.

Mira Azora

PACK CONTENTS CHECKLIST

Tick the appropriate boxes to familiarise yourself with the part names and to

conrm that the parts are included.

1 x Olive

1 x Compression Nut

1 x Mira Azora

Documentation

1 x Installation and User Guide 1 x Installation Template

1 x Guarantee and Registration Document

WIRING DIAGRAM

BROWN

RED

BROWN

GREEN BLUE

BLUE

BLACK

GREEN

Thermal Cutout

Disc

Tank Connection

Load

Inlet Connector

Pressure/Power

Selector Switch

Solenoid

Valve

Start/Stop

L.E.D.

START/STOP

Internal Wiring Diagram

SPECIFICATIONS

European Conformity Information

The Mira Azora shower complies with the following European directives:

2006/95/EC Low Voltage Directive, 2004/108/EC EMC Directive.

The Mira Azora shower is a high power appliance and is subject to conditional

connection. If the main electrical supply fuse is rated less than 80 Amps, the local

electricity supply company must be contacted to conrm if the electrical supply is

adequate.

The Mira Azora shower complies with the requirements of the UK’s water regulations.

Dimensions

Height 367 mm

Width 233 mm

Depth 100 mm

Electrical Variant

Azora 9.8

Nominal Power at 230 V ac 9.0 kW

Nominal Power at 240 V ac 9.8 kW

Recommended MCB Rating 45 A

Maximum Supply Cable Size 16 mm²

Recommended RCD Rating 30 mA tripping current

Recommended Isolator Switch 45 A double-pole with 3 mm contact separation

Appliance Sealing Rating IP X4 - Suitable for installation in Zone 1

Maximum Ambient Temperature 30°C

Minimum Ambient Temperature 2°C

Plumbing Variant

Azora 9.8

Minimum Dynamic Pressure 70 kPa (0.7 bar)

Maximum Dynamic Pressure 500 kPa (5 bar)

Maximum Static Pressure 1000 kPa (10 bar)

Minimum Static Pressure 20 kPa (0.2 bar)

Maximum Inlet Temperature 30°C

Minimum Inlet Temperature 2°C

Inlet Connection 1/2” BSP Male / 15 mm Compression Fitting

Maximum Water Hardness 200 ppm CaCO3

Outlet Connection 1/2” BSP Male

INSTALLATION REQUIREMENTS

Please read the Important Safety Information and specications sections at

the front of this guide, and the requirements detailed in this section before

installing the shower.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

Plumbing

1. The plumbing installation must comply with all national or local water regulations

and all relevant building regulations, or any particular regulation or practice

specied by the local water supply company.

2. Do not install the product in a position in which service access is limited.

3. Decide on a suitable position for the shower (minimum distance of 200 mm from

the ceiling to allow for cover t and removal).

4. The position of the shower and shower ttings must provide a minimum gap of

25 mm between the showerhead and the spill over level of any bath, shower

tray or basin and a minimum gap of 30 mm between the showerhead and the

spill over level of any toilet, bidet or other appliance with a Fluid Category 5

backow risk (see diagram on page 8).

5. The shower is suitable for installation within the shower area and is tted with

a pressure relief valve. It must be positioned over a water catchment area with

the controls at a convenient height for the user.

6. The shower must be tted to a waterproof at and even wall surface.

7. DO NOT t the shower to the wall and tile up to the case.

8. DO NOT seal the gap between the shower and the wall surface.

9. The showerhead should be positioned so that it discharges down the centre

line of the bath or across the opening of a shower cubicle.

10. The showerhead must be directed away from the shower unit, during normal

use the showerhead must not spray directly on to the shower unit.

11. DO NOT apply excessive force to plumbing connections; always provide

mechanical support when making plumbing connections. Any soldered joints

should be made before connecting the shower.

12. This shower is not designed to be plumbed directly from the rear. For rear-entry

supply, add an elbow to the supply pipe and connect as a rising or a falling supply.

13. If pipework and/or electrical cables enter the shower from the rear through a

hole in the wall provision must be made to prevent water ingress back into the

wall structure.

14. Only use the inlet connector supplied with the shower. DO NOT use any other

type of tting.

Hose Retaining Ring tted and shower ttings xed at a suitable height preventing

dirty water backow.

Note! There will be occasions when the hose retaining ring will not provide a suitable

solution for Fluid Category 3 installations, in these instances an outlet double

checkvalve must be tted, this will increase the required supply pressure typically

by 10kPa (0.1 bar). Double checkvalves tted in the inlet supply to the appliance

cause a pressure build up, which could exceed the maximum static inlet pressure

for the appliance and must not be tted. For Fluid Category 5 double checkvalves

are not suitable.

Zone of

Backow Risk

30 mm

Minimum

Toilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Electric

Shower

25 mm

Minimum

25 mm Minimum

15. A full bore/non restrictive servicing valve must be tted in a readily accessible

position adjacent to the shower to facilitate maintenance of the shower.

DO NOT use a valve with a loose washer plate (jumper) as this can lead to a

build up of static pressure.

16. A water treatment device should be installed where the water hardness may

exceed 200 ppm. Malfunctions caused by excessive limescale formation are

not covered by this shower’s guarantee (see back page for details).

17. The installation must not cause the hose to be sharply kinked during normal

use.

18. DO NOT perform the electrical installation until the plumbing has been

completed and checked for leaks.

Double-pole

Isolating Switch

Consumer Unit

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

Electrical

1. The electrical installation must comply with BS 7671 (commonly referred to as

the IEE Wiring Regulations) and all relevant building regulations, or any particular

regulation or practice specied by the local electricity supply company.

2. Ensure that all circuit protection devices, switches and cabling is adequate

for the rated current of the shower and that the rating of the electricity supply

company fuse and the consumer unit are adequate for the additional demand.

3. The shower must be earthed. Ensure any supplementary bonding complies

with the relevant regulations.

4. This shower is intended to be permanently connected to the xed electrical wiring

of the mains system. A separate supply must be provided from the consumer

unit to the shower.

5. DO NOT supply any other electrical equipment including extractor fans or pumps

via this product.

6. This shower must be provided with means for local disconnection that is

incorporated into the xed wiring in accordance with the relevant local wiring

regulations. This must be a double pole switch, which has at least 3 mm contact

separation in each pole. The switch can be a ceiling mounted pull-cord type within

the shower room or a wall mounted switch tted in the applicable zone area.

7. A 30mA Residual Current Device (RCD) is recommended to be tted in the

circuit to the shower.

8. DO NOT apply excessive force to the terminal block.

9. All electrical connections should be checked for tightness to prevent overheating

before switching on the electrical supply.

10. DO NOT switch on the electrical supply until the plumbing has been completed

and checked for leaks.

Plumbing and Electrical Schematic

INSTALLATION

Warning! Turn off the electrical and water supplies before proceeding with the

installation of the Mira Azora. The electricity must be turned off at the mains and

the appropriate circuit fuse removed, if applicable.

Note! An installation template is supplied to help you install the Mira Azora.

Remove the three cover retaining

screws and the cover.

Caution! Handle the glass cover

assembly with care.

Cover

Cover Retaining

Screw

Determine the direction and

route of the incoming water

supply: falling (entering the

shower from the top), or rising

(entering the shower from the

bottom).

Note! - DO NOT use an

incoming supply entering the

shower directly from the back.

Add an elbow to the supply

pipe and connect it as a rising

or falling supply.

Swivel the inlet connector

assembly to suit. Remove

the inlet blanking cap. Avoid

trapping the green earth

bonding wire.

Installation of Mira Azora

Wall xings are not supplied. For solid wall structures a red rawl plug and a

no. 8 x 1½” countersunk brass or stainless steel screw should be used. For

other wall structures such as panels alternative xings may be required. A

minimum of 3 xing screws should be used.

Inlet

Connector

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Pinoir K-2035 Bedienungsanleitung

Kohler

Kohler 72762T-9MND Bedienungsanleitung

Kohler

Kohler K-2293 Montageanleitung

Kohler

Kohler Botticelli K-2333 Montageanleitung

Kohler

Kohler K-1112 Montageanleitung

Kohler

Kohler K-3593 Bedienungsanleitung

Kohler

Kohler TROCADERO K-2247-1 Bedienungsanleitung

Kohler

Kohler Jarves K-5055 Bedienungsanleitung

Kohler

Kohler K-15599X Bedienungsanleitung

Kohler

Kohler 10282 Bedienungsanleitung

Kohler

Kohler 8030A Bedienungsanleitung

Kohler

Kohler K-6268 Montageanleitung

Kohler

Kohler K-7653 Bedienungsanleitung

Kohler

Kohler Stance 14787A Bedienungsanleitung

Kohler

Kohler STRAYT 37331A-4ND Bedienungsanleitung

Kohler

Kohler K-4991X Montageanleitung

Kohler

Kohler ELLISTON 72782T-4 Bedienungsanleitung

Kohler

Kohler 45432IN Bedienungsanleitung

Kohler

Kohler K-13108 Montageanleitung

Kohler

Kohler Escale K-7219 Bedienungsanleitung

Kohler

Kohler K-485 Montageanleitung

Kohler

Kohler K-3363 Bedienungsanleitung

Kohler

Kohler TAHOE Bedienungsanleitung

Kohler

Kohler Rainduet R97009T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung