Kohler Seawall K-6504 Bedienungsanleitung

Installation Guide

Deck-Mount Bath Faucet

with Handshower

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-6504

113762-2-CD

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Provide an access panel for all installations.

Carefully read this entire instruction manual before beginning the

installation; the illustrations do not show all possible

conﬁgurations.

These installations lead up to, but do not include, the wall-mount

shower arm installation.

Carefully inspect waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

This product is designed for use with the K-868 bath, K-870

whirlpool, or K-1398 whirlpool.

Install the faucet to the bath/whirlpool before installing the

bath/whirlpool.

The transfer valve contains an integral vacuum breaker.

Assorted

Screwdrivers

• Support blocks or

straps

• Elbows, tubing or

additional plumbing

hardware

• Drill

• Scissors

• Plumbers putty

Plus:

Adjustable

Wrench 5/64" and

5/32" Hex

Wrench

Safety

Glasses

Snap Ring

Pliers SolderPropane

Torch

Open End

Wrench

113762-2-CD 2 Kohler Co.

Before You Begin (cont.)

The deck width from the bath rim must be a minimum of 2″(5.1

cm) to allow clearance for the faucet ﬁttings.

Kohler Co. recommends hard-drawn tubing (type M, K, or L)

from the valves to the transfer valve to the spout.

Kohler Co. recommends soldering all connections from the

transfer valve to the spout as well as from the transfer valve to

the hot and cold valves.

To avoid potential leakage below the rim, do not use ﬂexible hose

connections.

Use 1/2″nominal tubing (5/8″OD) for the outlets and 3/4″

nominal tubing (7/8″OD) for the inlets.

Install water hammer arresters in the supply line.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Kohler Co. 3 113762-2-CD

1. Component Layout

Verify the location of the components and the orientation of all

ports.

Determine the location and orientation of the transfer valve. The

location of the bath spout, handshower, and the optional auxiliary

shower will affect the piping and connectors needed.

Allow clearance for valve outlets, handles, bath spout, and

handshower hoses.

You can extend the distance between the transfer valve and the

braided hose connection with 1/2″copper piping below the rim

of the bath/whirlpool, but it may not be safe or practical. A long

run of piping will mean a long run of room-temperature standing

water when the handshower is ﬁrst activated for use.

NOTE: The distance between the transfer valve and the braided

hose connection with 1/2″copper piping below the rim of the

bath/whirlpool, but it may not be safe or practical. A long run of

piping will mean a long run of room-temperature standing water

when the handshower is ﬁrst activated for use.

Secure long runs of piping to the underside of the deck or rim. If

the piping cannot be secured at a point near the transfer valve,

secure the piping from underneath with lumber or other suitable

support.

Hose Connection

Braided Hose

Decorative Hose

113762-2-CD 4 Kohler Co.

2. Preparation

For K-1398 Whirlpool Only:

CAUTION: Risk of personal injury. Wear safety goggles when

marking, prick punching, and drilling holes.

NOTE: Tape the templates into place to simplify procedure.

Position Template #1 on the bath rim (drain side) as shown.

Mark and drill two 1-1/2″(3.8 cm) holes for the valves.

Position Template #2 on the bath rim (drain side) as shown.

Mark and drill a 2″(5.1 cm) hole for the transfer valves.

Mark and drill a 1-1/4″(3.2 cm) hole for the handshower hose

guide.

Mark the centerline of the bath on the bath wall opposite the

drain side.

NOTE: Do not locate the template lower than 3″(7.6 cm) down from

the bath bench.

Position Template #3 (metal) on the bath rim (drain side) as

shown.

Mark the ﬁve hole locations on the bath wall.

Drill 1/8″(3 mm) pilot holes at each of the ﬁve locations.

At the center pilot hole, drill a 1-3/8″(3.5 cm) hole for the spout

sleeve.

Drain

Template #1

Template #2

Template #3 (Metal)

3" (7.6 cm)

Fastener Holes (4 Required)

Spout Sleeve Hole

Bath Bench

Centerline of

Bath Fitting

Kohler Co. 5 113762-2-CD

Preparation (cont.)

Refer to the hardware assembly kit to determine if your fastener

type is rubber or steel.

For rubber fasteners: Drill 1/2″(1.3 cm) holes at each of the

remaining four pilot hole locations.

For steel fasteners: Drill 3/8″(1 cm) holes at each of the

remaining four pilot hole locations.

113762-2-CD 6 Kohler Co.

3. Verify the Spout Tube Fit

Align the spout tube and spout sleeve with the pilot holes on the

bath wall.

Place the gasket over the spout sleeve.

Temporarily place the sleeve through the center hole on the bath

wall.

Loosely thread the retaining nut onto the sleeve.

NOTE: K-868 and K-870 have the fasteners pre-installed into the

bath wall.

For K-1398 Whirlpool Only:

Thread the rubber fasteners (supplied in the hardware kit) to the

tube assembly or install steel fasteners into the bath wall.

For All Installations:

Verify the alignment of the spout tube with the holes in the bath

wall.

Place the spout tube back into the carton for protection.

Prior to soldering, remove the fasteners and the spout sleeve.

Bath Rim

Gasket

Retaining Nut

Fasteners

Spout Tube

Sleeve

Kohler Co. 7 113762-2-CD

4. Install the Spout Sleeve

Determine which coupling will be required.

Verify adequate clearance away from the bath wall and framing

to allow for soldering the ﬁnal connection after the

bath/whirlpool is moved into place.

Solder the coupling to the sleeve.

Allow the assembly to cool before installing it to the bath wall.

After the assembly has cooled, place the gasket over the sleeve

assembly.

Apply a bead of sealant to the back of the sleeve and around the

back of the hole in the bath wall.

Slide the sleeve assembly through the bath wall.

Slide the rubber and ﬁber washers over the sleeve.

Secure the assembly to the bath wall by threading the retaining

nut onto the sleeve.

Sleeve

Coupling

Back of BathWall

Sleeve

Retaining Nut

Fiber Washer

Rubber Washer

113762-2-CD 8 Kohler Co.

5. Install the Hose Guide

Deck-Mount Installations

From the top of the ﬁnished deck, drill a 1-1/4″(3.2 cm)

mounting hole.

For All Installations

Slide the washer down the shank until it is ﬂush against the

ﬁnished deck.

Thread the escutcheon onto the shank until it is ﬂush against the

ﬁnished deck.

From the top of the bath or ﬁnished deck, insert the shank into

the mounting hole of the ﬁnished deck.

From the underside of the bath, thread the shank nut onto the

shank until it is ﬂush against the ﬁnished deck.

Secure the shank nut to the ﬁnished deck. Do not overtighten.

Hose Guide

Escutcheon

Washer

Shank Nut

Shank

Kohler Co. 9 113762-2-CD

6. Install the Valve Handle

Thread the mounting nut with the ﬂange side up onto each

″Cold″and ″Hot″valve handle.

Slide the ﬁber washer and the rubber washer onto each ″Cold″

and ″Hot″valve handle and onto the mounting nut.

NOTE: Valve handles that are marked ″Cold″must always be

installed into the mounting hole on the right as viewed from the

front of the bath.

From the underside of the bath, insert the valve handles up into

their respective mounting holes.

Thread a collar onto each valve body with the ﬂange side facing

upward. Thread the collar down until the distance between the

deck/rim to the top of the valve stem is 1-13/16″(4.6 cm).

Thread a mounting nut up to the underside of the deck/rim to

secure each valve in place.

Repeat the process for the second valve.

Valve Body

Mounting Nut

Fiber Washer

Rubber Washer

1-13/16"

(4.6 cm)

Collar Mounting Nut

113762-2-CD 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler 5EKD Bedienungsanleitung

Kohler

Kohler 74053T-4E2 Bedienungsanleitung

Kohler

Kohler 99859T Bedienungsanleitung

Kohler

Kohler K-11550 Bedienungsanleitung

Kohler

Kohler 72762T-9MND Bedienungsanleitung

Kohler

Kohler K-2282 Bedienungsanleitung

Kohler

Kohler FORTE 10433T-B4 Bedienungsanleitung

Kohler

Kohler K-8666X Bedienungsanleitung

Kohler

Kohler Sunstruck K-1967-GHW Bedienungsanleitung

Kohler

Kohler K-106 Montageanleitung

Kohler

Kohler K-98741 Montageanleitung

Kohler

Kohler K-8973 Montageanleitung

Kohler

Kohler Mira Sport J03A Bedienungsanleitung

Kohler

Kohler Reve K-5036BR Bedienungsanleitung

Kohler

Kohler Mira Zest Bedienungsanleitung

Kohler

Kohler K-T15231 Bedienungsanleitung

Kohler

Kohler K-10272 Montageanleitung

Kohler

Kohler K-77767K Montageanleitung

Kohler

Kohler STANCE 14760A-4ND Bedienungsanleitung

Kohler

Kohler K-2220X Montageanleitung

Kohler

Kohler K-4709 Bedienungsanleitung

Kohler

Kohler k-2815 Bedienungsanleitung

Kohler

Kohler Lyntier K-T10333 Montageanleitung

Kohler

Kohler 1114111 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung