Kohler K-T15231 Bedienungsanleitung

Installation Guide

Three-Handle Bath/Shower Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T15231 K-T15235

1010463-2-B

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Please read all instructions before you begin.

Observe all local plumbing and building codes.

Shut off the main water supply.

Do not remove the thread protectors until instructed to.

Before installation, unpack the components and inspect them for

damage. Return the components to the carton until you are ready

to install.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Strap

Wrench Thread

Sealant Plumbers

Putty

Hex

Wrench

1010463-2-B 2 Kohler Co.

1. Install the Diverter Trim

Remove the diverter sleeve.

Loosen the setscrew on the escutcheon.

Apply plumbers putty or other sealant to the underside of the

escutcheon according to the manufacturer’s instructions.

Push the escutcheon down onto the diverter until it rests against

the ﬁnished wall.

Tighten the setscrew and remove excess sealant.

Loosen the setscrew on the knob and install it on the diverter.

Tighten the setscrew on the knob.

Diverter

Apply plumbers

putty.

Setscrew

Escutcheon

Diverter

Sleeve Knob

Kohler Co. 3 1010463-2-B

2. Install the Spout

Threaded Spout Installation

Remove the temporary nipple.

Apply thread sealant to the 1/2″nipple threads on both ends.

Install a 1/2″nipple to extend the indicated distance beyond the

ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

of the spout according to the manufacturer’s instructions.

Carefully tighten the spout with a clean strap wrench and remove

all excess putty.

Flush hot and cold water through the spout for one minute.

Remove the temporary nipple.

Apply thread sealant and install a 1/2″copper tube so it extends

1-1/2″(3.8 cm) to 2-7/8″(7.3 cm) beyond the ﬁnished wall.

Deburr the copper tubing.

Loosen the setscrew with a 5/32″hex wrench.

1/2" Copper

Tube

1-1/2" (3.8 cm) to

2-7/8" (7.3 cm)

Apply

plumbers

putty.

Setscrew

5/32" Hex

Wrench

Slip-Fit Spout

1/2" Nipple

3-7/8"

(9.8 cm)

1/2" Nipple

(17.8 cm)

Apply plumbers putty.

Threaded Spouts

1010463-2-B 4 Kohler Co.

Install the Spout (cont.)

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Install the spout and carefully retighten the setscrew. Do not

overtighten the setscrew.

Remove all excess putty.

Kohler Co. 5 1010463-2-B

3. Install the Showerhead

CAUTION: Risk of product damage. To avoid plugging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple.

Apply a bead of plumbers putty or other sealant to the

escutcheon according to the manufacturer’s instructions.

Slide the escutcheon over the shower arm.

Apply thread sealant on the shower arm threads and thread the

shower arm into the elbow.

Tighten with a clean strap wrench. Do not overtighten.

Flush the system for one minute.

Apply thread sealant to the shower arm threads, and thread the

showerhead onto the shower arm. Tighten securely.

Remove all excess putty.

Shower Elbow

Apply plumbers

putty.

Shower Arm

Showerhead

1010463-2-B 6 Kohler Co.

4. Installing Acrylic Handles

Discard the thread protectors and apply a bead of plumbers putty

or other sealant around the edge of the escutcheons according to

the manufacturer’s instructions.

Turn each escutcheon clockwise onto the valves until they contact

the ﬁnished wall.

Remove any excess putty.

Close the valves (hot = counterclockwise, cold = clockwise).

Install the spline adapter onto the valve.

Slide the O-ring over the top of the insert.

Position the acrylic handle over the insert.

Align the handles. The higher ﬂared end of each handle should

face away from the spout horizontally.

To adjust the alignment move the spline adapter slightly until the

desired alignment is achieved.

Fasten the handle to the valve using the screw and washer

provided.

Insert the cap.

Escutcheon

Valve

Apply

plumbers putty.

Spline Adapter

O-Ring

Insert

Handle

Washer Cap

Screw

Kohler Co. 7 1010463-2-B

5. Installing Lever Handles

Measure the distance from the top of the valve stem to the

ﬁnished surface.

Use the brass spline adapter and screw when the valve stem

height is between 1-3/16″(3 cm) and 2-1/8″(5.4 cm).

Use the plastic spline adapter when the valve stem height is

between 2-1/8″(5.4 cm) and 2-5/16″(5.9 cm).

If the brass spline adapter is required, attach it using the supplied

screw. The plastic spline adapter does not require a screw.

Close the valves (hot = counterclockwise, cold = clockwise).

Align the handles with each handle lever pointing away from the

spout horizontally.

If the handles are not properly aligned, lift a handle off the spline

adapter and move it one or two ridges until it is properly

aligned.

Attach the handle by tightening the handle bonnet onto the valve

body.

6. Complete the Installation

Make sure all the connections are tight.

Open the drain.

Turn on the main water supply and check for leaks.

Escutcheon

Valve

Apply

plumbers putty.

Spline

Adapter

Escutcheon

Lever Handle

Plumbers Putty

Screw

Valve Body

Valve

Stem

Handle Bonnet

1010463-2-B 8 Kohler Co.

Complete the Installation (cont.)

Open the hot and cold valves and check for leaks.

Run the water for about a minute and turn off.

Kohler Co. 9 1010463-2-B

Guide d’installation

Robinets baignoire/douche à trois poignées

Outils et matériaux

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Veuillez lire toutes les instructions avant de commencer.

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Ne pas retirer les protecteurs de ﬁletage avant l’instruction de le

faire.

Avant l’installation, déballer les éléments et examiner

soigneusement pour en déceler tout dommage. Remettre les

éléments dans l’emballage jusqu’à l’installation.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Cléàmolette Cléà

sangle

Joint

d'étanchéité

pourfiletage Masticde

plombier

Clé

hexagonale

Kohler Co. Français-1 1010463-2-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Stillness 944-4 Bedienungsanleitung

Kohler

Kohler Seawall K-6504 Bedienungsanleitung

Kohler

Kohler 9076 Bedienungsanleitung

Kohler

Kohler K-9135 Montageanleitung

Kohler

Kohler K-1035-H2 Montageanleitung

Kohler

Kohler K-45415 Montageanleitung

Kohler

Kohler Evoke 6332A-4 Bedienungsanleitung

Kohler

Kohler K-T16237 Bedienungsanleitung

Kohler

Kohler K-7223 Bedienungsanleitung

Kohler

Kohler EX28096T-4 Bedienungsanleitung

Kohler

Kohler K-11830 Bedienungsanleitung

Kohler

Kohler K-8247 Montageanleitung

Kohler

Kohler K-15888 Bedienungsanleitung

Kohler

Kohler K-1110-G Kurzanleitung

Kohler

Kohler Levity K-706013-L Bedienungsanleitung

Kohler

Kohler K-15246X-S Montageanleitung

Kohler

Kohler K-3444K-NS Montageanleitung

Kohler

Kohler K-8297TW-HC-0 Bedienungsanleitung

Kohler

Kohler K-8998 Montageanleitung

Kohler

Kohler FLIGHT NEUS E62C70-00 Bedienungsanleitung

Kohler

Kohler K-7303 Bedienungsanleitung

Kohler

Kohler Portrait K-2272 Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic Bedienungsanleitung

Kohler

Kohler K-78172-BN Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung