Kohler Sensate K-72218-WB-BL Montageanleitung

Installation and Care Guide

Electronic Kitchen Sink Faucet

Français, page ″Français-1″

Español, página ″Español-1″

1318209-2-A

Tools and Materials

Before You Begin

WARNING: Risk of fresh water contamination. This faucet

contains back-siphonage protection. Do not remove any

internal components.

WARNING: When using electrical products, basic

precautions should always be followed, including the

following:

DANGER: Risk of electric shock. Connect only to a circuit

protected by a Ground-Fault Circuit-Interrupter (GFCI)*.

WARNING: Risk of electric shock. Grounding is required. A

qualiﬁed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before

servicing.

WARNING: Risk of injury or property damage. Please read

all instructions thoroughly before beginning installation.

CAUTION: Risk of property damage. The faucet spout

contains a magnet. Do not allow items susceptible to

electromagnetic damage to come into close proximity to the

spout.

Follow all plumbing, electrical, and building codes.

*Outside North America, this device may be known as a Residual

Current Device (RCD).

3/8"

Plus:

• Unswitched Electrical Outlet

• KOHLER Konnect App

1318209-2-A 2 Kohler Co.

Before You Begin (cont.)

CAUTION: Risk of product damage. This product contains

sensitive electronic components. Do not store open containers of

chemical or cleaning products near this product. Cleaning rags or

sponges must be rinsed with fresh water before storage.

IMPORTANT! Do not use a switch-controlled electrical outlet

(typically used for garbage disposals) to provide power to the

faucet.

Class 1 laser product: Complies with 21 CFR 1040.10 and 1040.11.

Observe all local plumbing and building codes.

Provide a constant unswitched 120 VAC electrical outlet located

below the sink within 5’ (1.5 m) of the control box.

Shut off the main water supply.

For new installations, assemble the faucet to the sink before

installing the sink.

For uneven mounting surfaces (such as tile grout lines), apply a

suitable sealant under the faucet. Do not use petroleum-based

sealant.

Kohler Co. 3 1318209-2-A

1. Prepare for Installation

NOTE: Handle orientation is designed to be on the right.

Thread the screws into the ring 1/4″(6 mm) past the surface.

Use the escutcheon included with your faucet.

Insert the faucet through the mounting surface with the handle

on the right.

1/4"

(6 mm)

Escutcheon

1318209-2-A 4 Kohler Co.

2. Install the Faucet

Slide the washer and ring over the outlet hose, then feed the

supply hoses and wires through.

Thread the ring onto the shank until the washer contacts the

underside of the sink.

Adjust the ring to align the screws with the front and back of the

faucet.

Use a Phillips screwdriver to securely tighten the screws.

Shank

Outlet Hose

Ring

Washer

1/4"

(6 mm)

Kohler Co. 5 1318209-2-A

3. Connect the Supplies

CAUTION: Risk of restricted water ﬂow and product damage.

Supply hoses must not be taut, kinked, or twisted during

installation. If the supply hoses must be coiled, maintain an inside

diameter (ID) of 3″(76 mm).

CAUTION: Risk of fresh water contamination. To prevent water

contamination, the check valves must be installed.

Connect the Supplies

Assemble a check valve to each supply.

Connect and tighten the supply hoses to the check valves.

Place a bucket under the outlet hose.

Turn on the supplies.

Flush the hot and cold water for 1 minute to remove any debris.

Connect the ﬂow sensor to the solenoid inlet.

Connect the outlet hose to the ﬂow sensor inlet.

Connect the Spray Hose

Solenoid

Weight

Outlet Hose

Ø 3"

(76 mm)

Min

Supply Hose

Check

Valve

Outlet

Hose

Inlet

Outlet

Spray

Hose

1318209-2-A 6 Kohler Co.

Connect the Supplies (cont.)

Remove the protective cap.

NOTE: The weight must be installed onto the spray hose to act as a

pull stop and to prevent kinking damage.

Slide the weight onto the spray hose.

Connect the spray hose to the solenoid outlet.

Kohler Co. 7 1318209-2-A

4. Connect the Wires

Apply grease (provided) to all connection sockets located on the

circuit board inside the cover. This will provide additional

corrosion protection.

Connect the handle switch and sensor wires from the faucet to

the circuit board.

Connect the power cord to the circuit board.

Connect the solenoid wire to the circuit board.

Connect the ﬂow sensor wire to the circuit board.

Plug the power cord into an unswitched 120 VAC outlet. The

power LED and connector status LEDs on the circuit board will

illuminate.

To test the activation of the sensor, refer to the ″Faucet Operation″

section.

Connect Your Faucet

Download the KOHLER Konnect App.

Follow the App instructions to connect to your faucet.

Handle

Switch

Solenoid

Power Cord

Sensor

Solenoid

Power

LED

Cover

Apply grease.

Connector

Status LEDs

Flow Sensor

1318209-2-A 8 Kohler Co.

Connect the Wires (cont.)

NOTE: Setup must be completed within 10 minutes.

When the Connector Status LED illuminates red, the system is

ready for mobile app setup.

If the Connector Status LED is ﬂashing red, unplug the power

cord to reset the system.

When the Connector Status LED is ﬂashing red and green, the

system is setting up.

When the Connector Status LED illuminates green, the system is

ready for use.

If the Connector Status LED is ﬂashing green, the router

connection was lost. Verify that the router is powered on and

within range.

If the Connector Status LED does not illuminate green, an

electronics reset is needed.

Electronics Reset

Open the handle to turn the faucet on.

Wave a hand over the sensor to turn the faucet off.

Close the handle.

Repeat the above steps 10 times in 1 minute to clear the proﬁle

information. If the above sequence is broken the count will reset

to zero.

Kohler Co. 9 1318209-2-A

5. Install the Solenoid

CAUTION: Risk of restricted waterﬂow. The outlet hose

must not be taut or kinked when installed. Locate the

solenoid valve within 7″(178 mm) to 8″(203 mm) of the

faucet centerline.

NOTE: Locate the solenoid valve within 7″(178 mm) to 8″(203

mm) from the faucet centerline. Allow adequate clearance for

servicing.

Mount the Bracket

NOTE: The mounting bracket should be secured with two suitable

fasteners (not supplied) based on the type and thickness of the

cabinet or wall material.

Fasten the mounting bracket vertically to the cabinet or wall.

Mount the Solenoid and Cover

Position the solenoid, ﬂow sensor, and cover on the mounting

bracket.

Solenoid

Wire

Mounting

Bracket

Tab

Cover

Solenoid

1318209-2-A 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler FAMILY CARE Bedienungsanleitung

Kohler

Kohler Symbol K-T18485 Bedienungsanleitung

Kohler

Kohler K-7779 Bedienungsanleitung

Kohler

Kohler K-T14419 Montageanleitung

Kohler

Kohler 23510-BL Bedienungsanleitung

Kohler

Kohler HiRise K-7344-4 Montageanleitung

Kohler

Kohler K-4986X Montageanleitung

Kohler

Kohler Family Care 2.0 K-701646T-FM-SHP Bedienungsanleitung

Kohler

Kohler K-7179 Montageanleitung

Kohler

Kohler K-307 Montageanleitung

Kohler

Kohler SIMPLICE 596T-4E Bedienungsanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler K-98741 Montageanleitung

Kohler

Kohler K-T16225 Bedienungsanleitung

Kohler

Kohler K-2958 Montageanleitung

Kohler

Kohler Wave 72687X-4 Bedienungsanleitung

Kohler

Kohler K-14431 Montageanleitung

Kohler

Kohler K-7127 Montageanleitung

Kohler

Kohler K-8703X Montageanleitung

Kohler

Kohler K-4709 Bedienungsanleitung

Kohler

Kohler K-T461 Bedienungsanleitung

Kohler

Kohler 13142-4A-CP Montageanleitung

Kohler

Kohler 73087T-B4 Bedienungsanleitung

Kohler

Kohler Carillon K-7806-95 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung