Kohler BARDON VITREOUS CHINA TOUCHLESS K-4915T-Y Bedienungsanleitung

2014

遵守当地所有给排水及建筑规定；

止水阀有1/2”NPT进水连接部分；

设备尺寸均属公称尺寸，符合美国国家标准A112.19.2-

2003的允许误差。

B.注意

开口/活动板钳

供水管和管件

卷尺

螺纹密封带

梅花板钳

螺丝刀

关闭冷水源

安装或重新安排供水管及出水管，使它们与安装尺寸保持

一致。

直流型安装尺寸要求请参阅图1

交流型安装尺寸要求请参阅图2

*当所装边缘距完工地面不高于432mm时，小便器即符合

美国残疾人法令的要求。

安装之前

请仔细阅读本说明书，以便熟悉所需工具、材料及安装

程序。请遵照相关章节进行安装，以避免由于安装不当

而导致不必要的损失。除了有关部门正确的安装方法之

外，还务请阅读所有操作安全说明。

本说明书所含一切材料，均以印刷时所有的最新产品为

准。科勒公司保留随时更改产品特性、包装或供应情况

的权利，恕不另行通知。

本说明书中的产品图例仅供参考,实际外形以实物为准.

本说明书包含了有关护理、清洁及保养等重要资料－请

交予用户保存。

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is base upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

The illustrations of product in this manual are only for

reference.

These instructions contain important care, cleaning, and

warranty information-please leave instructions for the

consumer.

BEFORE YOU BEGIN

A.HOW TO USE THESE INSTRUCTIONS A. 怎样使用本说明书

B. NOTES

Observe all local plumbing and building codes.

Stop Valve has a 1/2” NPT inlet supply connection.

Fixture dimensions are nominal and conform to

tolerances by ANSI Standard A112.19.2-2003.

Open end/adjustable wrenches

Supply piping and connectors

Tape measure

Thread sealant tape

Basin Wrench

Screw driver

Turn off cold water supplies.

Install or relocate supply tubing and waste pipe to conform

to roughing-in dimensions.

See Fig. #1 for DC roughing-in dimension requirements.

See Fig. #2 for AC roughing-in dimension requirements.

* Urinal complies with ADA requirement when rim is

mounted no higher than 17” form finished floor.

C. REQUIRED TOOLS AND MATERIALS C. 所需工具及材料

D. ROUGHING-IN D. 安装尺寸

巴尔顿 BARDON

安装说明书

INSTALLATION INSTRUCTIONS

釉面陶瓷感应小便器

VITREOUS CHINA TOUCHLESSTM URINAL

K-4915T-Y(0.5L/DC)/K-4915T-YC05(0.5L/AC)

K-4915T-W(1L/DC)/K-4915T-WC05(1L/AC)

K-4915T(3L/DC)/K-4915T-C05(3L/AC)

528137

1146969-T01-K

126

≈40mm

Bushing

电工套管

注意：供水管中心尺寸要求如上图。

供水管应凸出墙面22-32mm，否则将影响止水阀安装

及调节。

电工套管与墙面齐平，否则也将影响止水阀安装及调

节。

供水管内径不得小于10MM,否则将会影响冲洗效果。

NOTE:Roughing-in dimension requirements for

supply tubing as shown.

Supply tubing is 22-32mm out of the wall. Otherwise.

stop valve can not be installed and adjuested properly.

Bushing flush with the wall, Otherwise, stop valve can

not be installed and adjusted properly too.

Inner diameter of supply tubing is no less than 10mm,

otherwise the flushing will be affected.

1/2”N.P.S INLET

FOR STOP VALVE

止水阀连接

362mm

146±20mm

20mm

152mm

2”N.P.S TAP

内螺纹

OUTLET DETAILS

出水口详细图

2”N.P.S TAP

内螺纹

OUTLET DETAILS

出水口详细图

1/2”N.P.S INLET

FOR STOP VALVE

止水阀连接

152mm

12mm

≈20mm

Bushing

电工套管

610mm+

0mm

2”N.P.S TAP

内螺纹

533mm

603mm

76mm

*610mm

838mm

464mm

305mm

1029mm

To Floor

到地面

Fig.#2

图2

22-32mm

70mm

610mm+

0mm

533mm 2”N.P.S TAP

内螺纹

603mm

76mm

*610mm

838mm

464mm

305mm

1029mm

To Floor

到地面

Fig.#1

图1

* Recommended dimensions for installation only, please

adjust according to actual situation.

*仅为建议安装尺寸，客户可根据实际情况调整。

1146969-T01-K

CONNECT SUPPLY

请参阅图3

根据安装尺寸示意图安装挂钩。

在管螺纹处缠上密封带，在出水管上安装出水接头。将垫

圈装在出水接头处。

安装小便器，用螺丝和垫圈将小便器紧固在出水接头上。

警告：小便器有破损和崩裂的危险，不要将螺丝上得

过紧。

注意：不要给小便器顶部表面涂胶。涂胶会导致水箱盖无

法盖好。

1.安装小便器

1.MOUNT URINAL

See Fig.#3

Install hangers per roughing-in illustration.

Apply sealant tape to pipe threads and install female collar on

waste pipe. Place washer on female collar.

Install Urinal. Secure urinal to female collar with screws and

washers.

CAUTION:Risk of chipping or breaking urinal.Do not

overtighten screws.

NOTE:Do not caulk top surface of urinal.Caulk may prevent

tank cover from seating properly.

See Fig.#4

Apply sealant tape to pipe thread and install stop valve

assembly and tighten connection.

NOTE: Stop valve should face left side of tank when

tighten.

Please clean the inside of water supply pipe before connect-

ing to the product.

Plug seal ring into inlet hole of urinal.

Remove the nuts for fixing the bezel and the two clamps.

NOTE: While removing the nuts, avoid dropping bezel,

which may break urinal.

Take off the protection cap of the sensor window. Put the

sensor window into the bezel, fix sensor window with the

clamp and the nuts.

NOTE: Tighten the nuts slightly to prevent damage

sensor window (Do not over tighten the nuts.)

Hangers

挂钩

Collar

排水套环

Apply Sealant Tape

用螺纹密封带

Washer

垫圈

Fig.#3

图3

Clamp

夹钳片 Nut

螺母

Stop Valve

止水阀

Sensor Window

感应窗

Bezel

嵌板

Fig.#4

图4

1146969-T01-K

请参阅图4

将密封带缠在供水管螺纹处，安装止水阀，拧紧接口。

注意：拧紧时，止水阀应面对水箱左侧。

将本产品连接上供水管前，建议先冲洗干净供水管。

将密封塞嵌入小便器陶瓷件的进水孔中。

旋下固定嵌板用的两个螺母，取下两块夹钳片。

注意：旋下螺母时，防止嵌板掉落，砸坏小便器。

取下感应窗护盖后，将感应窗放入嵌板中，用夹钳片、

螺母固定感应窗。

注意：旋紧螺母时，不可过紧，防止损坏感应窗。

2. 联结供水

See Fig.#5

Loose the pipe clamp and adjust the position of plastic pipe

and outlet pipe. Do not tighen for the future adjustment. Put

the G1/2 washer into the connector of the pipe assy. Connect

the pipe assy with the valve assy.

Take off the protection cap from the connector assy.

NOTE: Do not screw the part between the connector

assy and the valve assy. Do not lose the filter assy when

taking off the protection cap.

请参阅图5

将胶管夹旋松，调整软管与出水管的位置，暂不拧紧胶管

夹，以备调整。将配件中的G1/2平垫放入配管组件的接

头后将配管组件与阀体组件连接好。

将保护帽从连接组件上取下。

注意：在安装过程中禁止拧动连接件组件与阀体组件

之间的连接部位。取下保护帽时，小心滤网组件丢失。

Please directly reference to Fig. #6 when installing

K-4915T, K-4915T-W or K-4915T-Y (DC).

Please directly reference to Fig. #7 when installing

K-4915T-C05, K-4915T-WC05 or K-4915T-YC05 (AC).

Put the valve assy and the pipes into the tank of urinal. Adjust

the distance of outlet pipe and plastic pipe. Then make the

outlet pipe aim at the sealing washer and make the valve assy

aim at the outlet of stop valve.

Plug the other end of outlet pipe into the sealing washer and

connect the valve assy with the stop valve.

At this time, all the pipes, valve assy and stop valve shall be

placed orderly. Tighten the pipe clamp and the net.

NOTE:

1. Do not lose the filter assy during the installation. The

distance between pipe clamp and the end of outlet pipe shall

be more than 20mm.

2. Adjust the stop valve assy to allow the location of the

bushing when install AC.

Plastic Pipe

软管 Pipe Clamp

管夹

Valve Assy

阀体组件

Protection Cap

保护帽

Outlet Pipe

出水管 G1/2 Washer

G1/2平垫

Connector Assy.

连接件组件

Filter Assy.

滤网组件

Fig. #5

图5

Fig. #6

图6

Pipe Clamp

管夹

Outlet Pipe

出水管

Sealing Washer

密封塞

Nut

螺母

20mm

1146969-T01-K

Stop Valve Assy.

角阀组件

Outer diameter of bushing

is no more than 25mm

电工套管

外径≤25mm

Control Box Assy.

电控盒组件

安装直流系列K-4915T、K-4915T-W 或K-4915T-Y请参阅图

6。

安装交流系列K-4915T-C05、K-4915T-WC05或

K-4915T-YC05请参阅图7。

将上一步骤连接好的阀体及管件移至小便器暗盒中，调整出

水管与软管的伸缩距离，使出水管对准密封塞，G1/2螺母

对准止水阀出水口。如图所示将出水管一端插入密封塞中，

将阀体组件与止水阀连接起来。

此时所有管件、阀体及止水阀都应放置整齐。拧紧胶管夹和

螺母。

注意：

1.此过程中防止滤网组件丢失。胶管夹应距离出水管端面至

少20mm。

2.安装交流型时，需调节角阀组件以让出电工套管的位置。

Please directly reference to Step 3 when installing

K-4915T, K-4915T-W or K-4915T-Y(DC).

Please match 16306T-NA AC power unit when install-

ing K-4915T-C05, or K-4915T-WC05, or

K-4915T-YC05(AC). The way of installation is as below.

CAUTION:

a. Do not connect 220V AC Power supply to DC

wiring terminal.

b. Do not damage the covering of AC power unit or remove

screws to avoid leakage.

安装直流系列K-4915T、K-4915T-W 或

K-4915T-Y请直接参考第3步。

安装交流系列K-4915T-C05或K-4915T-WC05或

K-4915T-YC05请选配16306T-NA交流电源盒，安装方式

如下：

警告：

a. 禁止将220V交流电源接入直流接线端。

b. 安装时严禁损伤交流电源盒外壳或移开交流电源盒盖螺

A. Fig.#8: AC power unit connect way:

AC power unit is connected to electric control box by

connection wire.

A.图8：交流电源盒连接方式：

交流电源盒通过连接线与电控盒相连。

Fig. #7

图7

Fig. #8

图8

Pipe Clamp

管夹

Outlet Pipe

出水管

Sealing Washer

密封塞

Nut

螺母

20mm

交流电源

Connector

接插件 Wire prepared

by customer

连接线用户自备

Connector

接插件

16306T-NA

AC Power Unit

交流电源盒 Connect with the same color wire,

and protect connect area by insulation tape.

请按电线颜色对接

连接处用绝缘胶布包好

1146969-T01-K

3. INSTALL BATTERIES(Only for DC)

B. When installing the power uint on the ceiling,please

layout bushing according to Fig.#9 and thread wire through

the bushing.

Fig.#9: Connection sketch while installing power uint on the

ceiling.

CAUTION: One AC power unit can supply two sensors

at most.

B. 将电源盒放在天花板上，如图示安装电工套管，管

内装入电线。

图9:交流电源盒安装在天花板上的连接示意图。

警告：一个交流电源盒最多可连接两个感应区。

See Fig.#10

Turn on stop valve. Inspect pipes for leakage in not flushing.

Connect the connector of sensor window with the connector

of solenoid valve.

Remove the battery box cover and insert alkaline batteries

into the battery box.Reinstall the cover of the baottery box

and tighten it with battery box with screws. Connect the

connector of battery box with the connector of the sensor

window.

See the section “Replace Batteries”.

NOTE: Do not lose the screws when removing the

cover of battery box. Tighten the screw, otherwise the

batteries may be affected with damp.

Notice:

a. Keep the connector away from water.

b. Don’t mistake the direction of inlet and outlet.

c. Do not connect the DC output of AC power unit to AC

power supply.

d. Do not connect to power supply while installing. Connection

line is not supplied. AC connection wire with insulating

sleeving is recommended. Wire of which the nominal sectionn

area of conductorisnot less than 0.5mm2is also recommend.

DC connection line use wire of which the nominal section area

is not less than 0.3mm2. It is cut according to acted installation

requirements (The length of cut wire is recommended less than

10m).

e. The head AC power supply must be protected with

appropriate fuse.

f. Please confirm the AC power supply and water supply should

be shut off before maintaining the products with AC power

related.

注意:

a. 不要让电线接插件接触水。

b. 不要将进出水方向弄错。

c. 不可将交流电源盒的直流输出端与交流电连接。

d. 安装时不要向电源盒供电。连接线请用户自备，建

议交流电源线采用导体标称截面积≥0.5mm2的电线，

直流连接线采用导体标称截面积≥0.3mm2的电线，

电线长度根据实际安装需要自行裁剪（建议连接线

长度小于10m）。

e. 交流电的总电源必须有合适的熔断丝加以保护。

f. 维修时必须断开交流电源并关闭水源。

Fig. #10

图10

Fig. #9

图9

Ceiling

天花板

Bushing

电工套管

AC Power Unit

交流电源盒

1146969-T01-K

3.安装电池(仅适用于直流型)

请参阅图10

打开止水阀，检查管道的密封应无任何渗漏。将感应器

接线端子与阀体电磁阀接线端子相连。

将电池盒盖取下，将碱性电池放入电池盒中，盖上电池

盒盖，拧紧螺丝。将电池盒接线端子与感应窗接线端子

连接。

参考“电池更换”。

注意：取下电池盒盖过程中防止螺丝丢失。盖上电

池盒盖时螺丝必须拧紧，螺丝不拧紧将使电池受潮。

请参阅图11

打开水箱盖包装，并取出所有物品。

把水箱盖有保护装置的一面倒置，以免损伤水箱盖表

面。

把挂钩置于水箱盖内。

注意：如有必要，可与图示相反方向放置挂钩。在小

便器两侧，用5/8”板钳组装并拧紧螺母。

警告：小便器有破损和崩裂的危险。不要将螺丝

上得过紧。

把水箱盖置于小便器上。

See Fig.#11

Open tank cover lock package and remove contents.

Place tank cover upside down on a protected surface to

prevent damage to tank cover finish.

Place hooks inside tank cover.

NOTE: If necessary, engage the hooks facing opposite the

direction illustrated.

Using a 5/8” wrench,assemble and tighen nut, washer and

lock nut on both sides of urinal.

CAUTION: Risk of chipping or breaking urinal. Do not

overtighen screws on urinal.

Put tank cover on the urinal.

Using supplied locking tool, install and tighen screw.

Check that tank cover is properly locked.

4. INSTALL TANK COVER

4. 安装水箱盖

Fig. #11

图11

Screw

螺丝

Hook

挂钩

Sleeve

套筒螺丝

Nut

螺母

Washer

垫圈

1146969-T01-K

请在通电10分钟后开始使用该系统。

因为此段时间设定为调节感应范围得待机状态。此时系

统不工作。

接上电源约十分钟为自动调节距离状态，此过程中系统

无冲水动作。在接通电源之前，务必清理感应冲洗器窗

口前得杂物，保证感应窗口前无任何物体，以免影响自

动调距。

约十分钟后感应器开始正常工作，如发现冲水量过小，

可参考”冲洗时间设定“进行改变冲洗时间，从而改变冲

水量大小。(仅适用于K-4915T或K-4915T-C05)

在接通电源之前，务必清理感应冲洗器窗口前得杂物，

以免影响自动调距。

电池的更换(仅适用于直流型)

电池耗尽时，电池指示灯将每隔2秒闪烁一次，感应器停止

工作，直至更换电池。更换时打开电池盒盖，换上新电池即

可。

注意：更换时注意电池极性。新旧电池不可混用。

过滤装置的清洗

初装一段时间或长期使用后，发现出水量明显变小，可清

洗阀体中的过滤装置。

旋下螺母，取出滤网，清洗后重新装入即可。

注意：清洗前，请先关闭止水阀。

Don’t use this system after 10 minutes power on.

The induction distance will be adjusted and this system will

not work during this time.

The state of distance adjustment has been last about 10

minutes after power on. No flushing druing this period.

Before power on, clear the unwantedobjects in front of the

sensor window to shortening the sensing distance.

The sensor will begin to work normally after 10 minutes. If

flushing water volume is not enough, reset the flushing time

referring to “Flushing Duration Setting” in order to changing

the flushing water volume. (Only for K-4915T or K-4915T-

C05)

Before power on, clear the unwantedobjects in front of the

sensor window to shortening the sensing distance.

When the batteries are nearly exhausted, the indicator will flush every 2

seconds, the sensor stop working until new batteries are changed.

When changing the batteries, open the cover of battery box and insert

new batteries.

NOTE: Pay attention to the pole of batteries and do not use new and

old batteries at the same time.

If the flushing volume is reduces,the filter assy must be cleaned.

Remove the nut and take out the filter assy. clean it with a brush

and reinstall.

NOTE: Turn off the Stop valve before cleaning.

WORKING STATUS FLUSHING 工作状态

REPLACEING BATTERIES

(Only for DC)

CLEAN THE FILTER ASSY

Screws

螺钉

Batteries

电池 Cover of Battery box

电池盒盖

Battery box

电池盖

Valve Assy

阀体组件

Nut

螺母

Filter Assy

滤网组件

Stop Valve

止水阀

1146969-T01-K

Manual Flushing

初装时或使用过程中，如感觉出水量过小（因水压偏低造

成），可以对感应冲洗阀的后冲洗时间进行调节。

拔掉电源，待感应指示灯完全停止闪烁后，再接上电源。

在接上电源的10分钟内，将配备的专用磁棒紧贴感应窗口

中间位置，持续约8秒左右，产品有一次出水过程，移走磁

棒，设置成功。

注意：此过程会产生自动调距，因此人体不可久留。

If the flushing volume is reduced, the flushing duration can be

adjusted.

Power off until the indicator stops flashing. During the first 10

minutes after power on, approach the flushing control stick to

the center of the sensor window for about 8 seconds.

Remove the flushing control stick after a flushing cycle.

NOTE: The indicting distance will be adjusted. Any

object shall move from in front of the sensor window.

当2分钟内连续3-4人以上使用时，小便器自动冲洗一

次。

The urinal will take a flush automatically when it’s used 3 or 4

times in 2 minutes.

保持窗口清洁，可用蘸有中性清洁剂的软布擦洗。

注意：

a.禁止使用去污粉、研磨粉及油类、酸性类、碱性类清

洁剂。

b 禁止直接对感应窗口喷洒空气清新剂、消毒液或其他

除臭、清洁类有机溶剂。

c 避免水直接接触电线接插件。

d 勿撞击感应窗口。

Keep the sensor window clean. wipe the soft cloth and mild

cleaner.

NOTE:

a. Do not use dust-removing powder, abrasive powder or cleaner

containing oil, acid or alkaline ingredient.

b. Do not spray air-refresher, disinfect, or other deodorizing,

cleaning solvent directly into the sensor.

c.Keep wire away from water.

d. Don’t attack the sensor window.

将配备的专用磁棒（冲洗控制棒）靠近感应窗口中间位

置，此时系统进入手控状态，感应指示灯每1秒闪烁一

次。用冲洗控制棒靠近感应窗口中间位置即放水冲洗，

再靠近则停止出水。此状态将维持8分钟，结束后转为

正常工作状态（状态结束时，如正在冲水，将被自动关

闭）。

注意：

每次冲水时间最长为30秒。冲洗控制棒如持续超过30

秒一直不离开感应窗口，将自动解除手控冲洗状态回复

Approach the supplied special magnetic stick (flushing control

stick) to the middle part of the sensor lens. The system is now at

a manual status and the indicator will flash every 1 seconds.

Approach the flushing control stick to the window, it ll start to

flush; approach again, stopping flushing. This status will last

for 8 minutes until it turns to the normal working status. (The

flushing, if any, will be terminated when this status ends).

Notice:

The longest flushing time is 30 seconds once. If the flushing

control stick keeps near to the sensing window, the manual status

will be terminated automatically and reassume the normal working

status.

FLUSHING DURATION(Only for K-4915T and K-4915T-C05)

冲洗时间设定(仅适用于K-4915T和K-4915T-C05)

DEODORIZING FLUSHING 防臭冲洗

CARE & CLEAN 清洁保养

手控冲洗

Flushing Control Stick

专用磁棒

1146969-T01-K

使用后冲洗

两段冲洗

(K-4915T、K-4915T-C05)

Flushing after used

感应器规格

0.05-0.86MPa.0.05-0.86MPa.

水压为0.18~0.55MPa.时,

Water pressure at 0.18~0.55MPa.,

the average flushing i

than 1L

(K-4915T-W or

K-4915T-WC05)

s notmore 平均冲水量不大于1L

(K-4915T-W、K-4915T-WC05)

水压为0.18~0.55MPa.时,

平均冲水量不大于3L

(K-4915T、K-4915T-C05)

(K-4915T-W、K-4915T-WC05

K-4915T-Y、K-4915T-YC05)

220V AC 50/60Hz(交流型)

220V AC 50/60Hz(AC)

2节7号碱性电池(AAA X 2)(直流型)

2 piece of AAA sized alkaline

batteries(DC)

Model 型号

K-4915T(3L/DC)

K-4915T-W(1L/DC)

K-4915T-C05(3L/AC)

K-4915T-WC05(1L/AC)

K-4915T(3L/直流型)

K-4915T-W(1L/直流型)

K-4915T-C05(3L/交流型)

K-4915T-WC05(1L/交流型)

Power Supply

Power Consumption The batteries can be used about

two years(4000 times a month)

Induction Distance

Detection Duration

Flusing Mode

Flusing Water Volume

Deodorization Flushing

Starting Pressure

Operation Temperature Ambient(water) temperature of

1℃-55℃

One forced flushing will be

conducted if the urinal is being

used continuously for 2 minutes.

Average flushing volume is not

more than 3L at pressure

0.18~0.55Mpa(K-4915T or

K-4915T-C05)

Double flushing(K-4915T or

K-4915T-C05)

About 2 seconds or 5 seconds

(automatic adjustment)

Automatic adjustment according

to the ambient circumstance

电源

电池使用寿命约2年（每月使用4000次）

感应距离视使用环境自动调节

检测时间约2秒或5秒（自动调节）

冲洗方式

冲洗水量

防臭冲洗

启动水压

使用温度

2分钟不间断连续使用时，强制

冲洗一次

环境1℃-55℃（水温1℃-55℃）

推荐供水压力（进水口流动水压）0.18~0.55MPa.

Recommended water supply pressure(dynamic pressure at

inlet): 0.18~0.55MPa.

SENSOR SPECIFICATION

K-4915T-Y(0.5L/DC)

K-4915T-YC05(0.5L/AC)

K-4915T-Y(0.5L/直流型)

K-4915T-YC05(0.5L/交流型)

(K-4915T-W, K-4915T-WC05,

K-4915T-Y, K-4915T-YC05)

Water pressure at 0.18~0.55MPa.,

the average flushing i

(K-4915T-Y or K-4915T-YC05)

s notmore

than 0.5L

水压为0.18~0.55MPa.时,

平均冲水量不大于0.5L

(K-4915T-Y、K-4915T-YC05)

1146969-T01-K

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler K-29918T-NSHC Bedienungsanleitung

Kohler

Kohler K-11452 Montageanleitung

Kohler

Kohler K-3393 Bedienungsanleitung

Kohler

Kohler OVE K-25217T-S2 Bedienungsanleitung

Kohler

Kohler K-4737 Montageanleitung

Kohler

Kohler K-17181 Bedienungsanleitung

Kohler

Kohler EIR K-77795KR-EX-0 Montageanleitung

Kohler

Kohler Rialto Pressure Lite K-3404 Bedienungsanleitung

Kohler

Kohler K-3399 Montageanleitung

Kohler

Kohler K-8423A-0 Montageanleitung

Kohler

Kohler Botticelli K-2352 Bedienungsanleitung

Kohler

Kohler PORTRAIT LITE K-4217 Bedienungsanleitung

Kohler

Kohler K-5401 Bedienungsanleitung

Kohler

Kohler K-4734-NY Montageanleitung

Kohler

Kohler Escale K-25089T-S Bedienungsanleitung

Kohler

Kohler C3-325 Bedienungsanleitung

Kohler

Kohler ESCALE K-95027T Bedienungsanleitung

Kohler

Kohler K-3997 Montageanleitung

Kohler

Kohler STERLING 402076 Montageanleitung

Kohler

Kohler K-3749 Bedienungsanleitung

Kohler

Kohler K-3654-7 Montageanleitung

Kohler

Kohler GABRIELLE CLASS FIVE S-EB K-3322T-W Bedienungsanleitung

Kohler

Kohler FAMILY CARE S-TRAP K-23191T-NS Bedienungsanleitung

Kohler

Kohler Intelligent Toilet Montageanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung