Kongskilde 2800 SERIES Bedienungsanleitung

2800 DOUBLE FOLD

FIELD CULTIVATOR

Kongskilde

2800 Series

*Model may not be exactly as shown.

Kongskilde reserves the right to make changes to product designs and

speciﬁcations without notice or obligation to rework.

See your local Kongskilde representative for current product speciﬁca-

tions, instructions and options.

ASSEMBLY INSTRUCTIONS

North American Version

Index

Introduction & Pre-assembly Instructions: ........................................................................3

Tines: ..................................................................................................................................5

Mounting Wheels on the Centre Frame: ............................................................................7

Assembling the Centre Frame: ...........................................................................................8

Self Levelling Linkages & Hair Pins: ................................................................................9

Hinge Assembly: ..............................................................................................................11

Cross Brace Installation: ..................................................................................................12

Hitch Assembly: ...............................................................................................................13

Cylinders: .........................................................................................................................15

Wing Cylinder Pins:......................................................................................................... 16

Adjustment Point Attachment: .........................................................................................17

Mechanical Adjust Wheel as Front Gauge Wheel: ..........................................................18

Fold Cylinders Installed: ..................................................................................................19

Outside Wing Fold Cylinders Installed ............................................................................20

Single Point Assembly: ....................................................................................................21

Hydraulic Assembly Information: ....................................................................................22

Installing the Product Identiﬁcation and Safety Decals: ..................................................25

On Completing the Assembly: .........................................................................................28

Notes: ...............................................................................................................................29

Introduction:

Please take the time to carefully read all the instruction booklets provided with your new Kongskilde

product. Once you are ﬁnished reading do not throw these guides out. Keep them for later review.

The "Spare Parts List" is referenced to by this guide. We suggest having it on hand during the assembly

process.

Accessories may have their own instruction guide. Please read the relevant booklets for instructions

on how to perform the installation of accessories. (Harrows, light kit

etc.)

Be sure to read and understand the "Owner's Manual" before operat-

ing this equipment. It contains information about adjustment settings,

operating instructions and safety precautions.

Please ﬁll out and return the Owners Registration and Warranty Form

provided in the Owners Manual to activate the warranty.

Pre-assembly Instructions:

Assembly of Kongskilde products should only be undertaken by

authorized Kongskilde Dealers or an approved service provider with

the necessary tools, equipment and training for safe assembly of the

unit.

Frame components are heavy and somewhat awkward to handle.

Proper lifting devices such as overhead cranes, boom lifts or mobile

lift trucks should be used at all times when moving or handling the

large frame components.

Proper steel assembly stands or support jacks should also be used to

support the frame components, preventing them from falling. Recom-

mended assembly tools include:

A full set of standard open or box end wrenches and sockets; assorted sizes of pin punches; a heavy

hammer and/or sledge hammer; a pry bar; a large adjustable wrench; and pair of visegrip or similar

type pliers.

Optional tools could include an all purpose jack and a good quality air or electric drive impact tool

with heavy drive sockets.

The assembly area should be should be large enough to allow workers and equipment to move around

freely during assembly of the unit. For example; to fully assemble a 2800 Double Fold with 8m work-

ing width, a minimum area of 12M x 13M with an overhead clearance (wing fold) of 7M is needed

(12M x 13M x 7M)

If the unit is to be assembled and folded indoors, additional clearance may be needed in the assembly

area.

The ceiling height and the size of the building exit door must also be considered in order to safely fold

and move the cultivator outdoor after assembly.

The ﬂoor area should be level and clean.

Be sure to check the packing slip to be certain everything is present.

Carefully unpack and lay out all of the fasteners and hardware. Sort and organize the hardware by

type and size.

Some of the components of the cultivator are very heavy. Extra care should be exercised when working

with these parts. Be sure to properly support all large components, especially the frames. Proper supports

protect the assembler, the product and the workspace. Improper supports can lead to accidents causing

injury or death as well as damaging the product, which can make it difﬁcult to sell. On this page and

the next are examples of good supports for a frame.

Moving heavy parts can be hazardous. Use proper equip-

ment for heavy lifting, and make sure that it is operated by

certiﬁed technicians. Failure to do so can lead to accidents

and injuries.

Utilizing proper supports stabilize the frame and make the

assembly safer and easier. In the example below example

steal saw horses are used to prevent swaying while the frame

is supported by an overhead crane.

Safety should be the ﬁrst concern of anyone assembling

a Kongskilde cultivator. Such an assembly can be a safe

project, if the assembler takes the appropriate steps, and

applies a bit of common sense.

Support here.

Supporting the frame prevents damage to

the product.

Fastners sorted for ease in assembly.

Tines:

Each tines must be assembled and then attached. Assembly is

straight forward simply look up the exploded view of the tine in

the "Spare Parts List." This contains all the information needed

to assemble the individual tines.

Once the tines are assembled, they must then be attached to the

toolbar. There is a booklet that came with the machine called

"Tine Patterns." This booklet contains a number of different ar-

rangement of tines design for different soil conditions. Chose an

appropriate pattern for the conditions expected and then attach

the tines where indicated by the pattern. The actual attachment

is shown in the picture in the upper right.

For the VT 2800 the tines can be attached in a number of different patterns.

For the VTH and the Conser-tine the standard patterns are: 10cm (4") and 15.5cm

(6"). These patterns are included in the tine pattern book.

These tine patterns show measurements from the centre line (marked with an M)

of the cultivator frame to the centre of each tine. Once the tine has been placed,

remember to tighten it.

Most tines can be assembled separately and later attached to the frame. The VFM

tines is the exception (see next page). The VTH Tine

An attached tine

Note:10cm or wid-

er sweeps can

not be placed

on toolbar behind

the outer tandem

wheels Sweep

will interfere with

tire. Use only 7 cm

goose-foots hare in

these locations

A warning for those attaching tines

The VFM Tine

Assembly Information for the VFM Tine:

The VTM tines are larger than most other tines. For this reason this the stem of

the tine will interfer with attachment of the tine to the toolbar. Hence, the tine

can not be assembled prior to being attached to the toolbar.

To avoid this problem assemble the tines in the following order. Begin by bolt-

ing the clamp to the toolbar (1 in the diagram below) in the position indicated

by the tine pattern. Then attach the coil (2) to the clamp using the spacer. Next

bolt the stem (3) to the coil. Finally fasten the sweep (4) to the tine. Check the

“Spare Parts List” for the types of fastners needed at each step.

Once the assembly is complete check the individual nuts and bolts to make sure

they are tight.

The tine pattern for this tine is found in the tine pattern booklet.

Tine Assembly Diagram

The linkage length from centre to centre, labelled with

an "A" in this drawing, should be set at:

A = 71cm (28") for VTM tines.

A = 73cm (28.5") for VTH tines.

Mounting Wheels on the Centre Frame:

The next step in the assembly is attaching the wheels to the centre frame. The top picture shows the

wheel assembly and the lower picture shows the exploded view of the wheel assembly.

8000lbs. Centre frame

Wheel assembly.

Assembling the Centre Frame:

The diagram below shows how to assemble the centre frame.

The front frame attaches to the rear frame as shown above. Use the bolts listed in the "parts book". Be

sure to bolt both top and bottom holes in the front and back. Remember to tighten them well.

Self Levelling Linkage & Ring Cotter Pin:

Check the assembly of the self-levelling linkages and make sure all of the clip pins are installed and

locked.

Unlocked Pin Locked Pin

"Self-levelling link"

Front hitch

pivot link

Detail view of front linkages on

the centre frame.

Andere Handbücher für 2800 SERIES

Inhaltsverzeichnis

Andere Kongskilde Landwirtschaftliche Geräte Handbücher

Kongskilde

Kongskilde KG 10 Bedienungsanleitung

Kongskilde

Kongskilde 2800 SERIES Bedienungsanleitung

Kongskilde

Kongskilde Z 685 Pro Bedienungsanleitung

Kongskilde

Kongskilde 300FS Bedienungsanleitung

Kongskilde

Kongskilde R+ 1610 S Bedienungsanleitung

Kongskilde

Kongskilde Z 8805 Bedienungsanleitung

Kongskilde

Kongskilde FRONT TERRA-C Bedienungsanleitung

Kongskilde

Kongskilde Z 665 HYDRO Bedienungsanleitung

Kongskilde

Kongskilde R+ 420 Bedienungsanleitung

Kongskilde

Kongskilde KC Bedienungsanleitung

Kongskilde

Kongskilde KCT Bedienungsanleitung

Kongskilde

Kongskilde DGC 102 Bedienungsanleitung

Kongskilde

Kongskilde R+ 820 Bedienungsanleitung

Kongskilde

Kongskilde GXF 3205 P Bedienungsanleitung

Kongskilde

Kongskilde DPC 40 Handbuch

Kongskilde

Kongskilde VIBRO TILL 2800 Bedienungsanleitung

Kongskilde

Kongskilde R 655 DS Bedienungsanleitung

Kongskilde

Kongskilde DEMETER CLASSIC CS Bedienungsanleitung

Kongskilde

Kongskilde FCT 1360 Bedienungsanleitung

Kongskilde

Kongskilde R 285 DS Bedienungsanleitung

Kongskilde

Kongskilde Vibro Crop Series Bedienungsanleitung

Kongskilde

Kongskilde K 20 C Handbuch

Kongskilde

Kongskilde 9200 DF Bedienungsanleitung

Kongskilde

Kongskilde VENTUS 2400 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung