Kramer AFM-20DSP-AEC Bedienungsanleitung

AFM-20DSP-AEC Quick Start

P/N:

2900- 301486QS

Rev:

Scan for full manual

AFM-20DSP-AEC Quick Start Guide

This guide helps you install and use your AFM-20DSP-AEC for the first time.

Go to www.kramerav.com/downloads/AFM-20DSP-AEC to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

AFM-20DSP-AEC 20 Port Audio Matrix

1 Set of rack ears

1 Quick Start guide

1 Power cord

4 Rubber feet

Step 2: Get to know your AFM-20DSP-AEC

Feature

Function

STATUS LED

Indicates the system’s status:

•3 cycles of red/blue/off/green LEDs

that flash in sequence for 30 seconds

when the system starts up, and the

application has not been launched.

•Flashes green when the application starts.

•Stays green when system is ready for use.

PORTS LEDs (1 to 20)

Indicate the port’s status:

•Green when an input signal is

detected, and the port is defined as

line in.

•White when defined as line out.

•Blue when defined as mic in.

•Red when in clipping state.

•Yellow when in limiting state.

•Off when there is no signal on the input.

IN OUT Dante™LEDs

(1 to 4)

Indicate the Dante’s signal status:

•Green when a signal is detected.

•Red when clipping occurs.

•Yellow when in limiting state.

•Off when no signal is detected.

HDMI™ LEDs

EMBED

Turns green when an analog audio signal is associated with the HDMI OUT signal.

Otherwise, it stays OFF.

DE-EMBED

Turns green when the HDMI IN audio signal is detected. Otherwise, it stays OFF.

IN OUT USB or S/PDIF LEDs

Indicate the USB or S/PDIF’s status:

•Green when a signal is detected.

•Off when no signal is detected.

If a signal is detected on one channel, either left only or right only, the status LED is

green.

CH 1(L)/CH 2(R) AMPLIFIER

LEDs

Indicate the amplifier’s signal status:

•Green when a signal is detected.

•Off when no signal is detected.

On the web page, CH1 and CH2 are referred to as AMP 1 and AMP 2, respectively.

Feature

Function

PORTS 3-pin Terminal Block

Connectors (1 to 20)

Interchangeable balanced mono-audio ports. Connect to an audio source or acceptor in 1

of 8 selectable I/O configurations: 16x4, 14x6, 12x8, 12x8 AEC ,10x10, 8x12, 6x14, 4x16.

Define each port as line in, mic in, mic + 48V in, or line out.

USB

AFM-20DSP-AEC can process the USB audio as a stereo speaker or operate as an audio

line-in or microphone for an audio recorder application or call conferencing.

When the AFM-20DSP-AEC is connected to a computer via USB-B:

•In the computer’s Settings > Manage sound devices > Output devices, the AFM-

20DSP-AEC USB shows as “Speaker USB AUDIO CODEC”.

•In a computer recoding application, the audio input settings for AFM-20DSP-AEC

show as “Line USB AUDIO CODEC”.

Important:

•The computer’s “Output” device (such as speakers) shows in the AFM-20DSP-AEC

embedded web pages as a USB Digital “Input”.

•The computer’s “Input” device (such as a microphone) shows in the AFM-20DSP-

AEC embedded web pages as a USB Digital “Output”.

HDMI™ OUT Connector

Connect to an HDMI acceptor to embed an audio signal from the matrix.

HDMI™IN Connector

Connect to an HDMI source to de-embed the audio signal (the video signal is passed

through to the output).

S/PDIF OUT RCA Connector

Connect to a digital stereo audio acceptor.

S/PDIF IN RCA Connector

Connect to a digital stereo audio source.

SPEAKER OUT

Outputs two selected audio signals in two channels.

•For Lo-Z: connect stereo output to Lo-Z speakers: L+ and L- to the left speaker;

R+R- to the right speaker.

•For Hi-Z (70V or 100V): connect Hi-Z and COM to mono Hi-Z speakers.

Dante PoE RJ-45 Port

Connect to Dante audio through the network. Provides 4 Tx channels and 4 Rx channels.

By default, DHCP is enabled.

RS-232 3-pin Terminal Block

Connector

Connect to a PC/serial controller to control the device.

ETHERNET RJ-45 Connector

Connect to a PC via a LAN to control the device and for firmware upgrades.

Micro USB PROG. PORT

Connect to your PC to control the device.

RESET Recessed Button

Press and hold for 5 seconds, to reset the configuration to its default parameters.

Mains Power Connector and

Fuse

Plug in for the power cord.

POWER Illuminated Power

Switch

Turns the device on and off.

Step 3: Mount AFM-20DSP-AEC

To rack mount the machine, attach both rack ears

(remove the screws from each side of the machine

and replace screws through the rack ears) or place

the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always turn off the power on each device before it is connected to the AFM-20DSP-AEC device.

For optimum range and performance, use the recommended Kramer cables available at

www.kramerav.com/product/AFM-20DSP-AEC. The use of third-party cables may cause damage!

Step 5: Connect the power

Connect the power cord to AFM-20DSP-AEC and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Operate AFM-20DSP-AEC

To operate AFM-20DSP-AEC, use:

•Embedded web pages via the

Ethernet.

•RS-232 serial commands

transmitted by a touch screen

system, PC, or other serial

controller.

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example: (adjust the amplified audio from analog audio 1 to -10dB):

#x-aud-lvl out.amplified_audio.1.audio.1,-10

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.0.0

TCP Port #:

5000

Gateway:

192.168.0.1

Username/Password

Admin/Admin

Factory Reset

Recessed Button

Press and hold for 5 seconds to reset the configuration to its

default parameters.

Protocol 3000:

“#factory” command.

Web Pages:

In the Settings page, click Factory Reset.

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer VS-44UHD Bedienungsanleitung

Kramer

Kramer VP-4x4K Bedienungsanleitung

Kramer

Kramer Sierra Video 1204V5S Bedienungsanleitung

Kramer

Kramer VS-44HN Bedienungsanleitung

Kramer

Kramer Sierra Video 3248V5Sxl Bedienungsanleitung

Kramer

Kramer VS-42H Bedienungsanleitung

Kramer

Kramer VS-88UHD Bedienungsanleitung

Kramer

Kramer VP-4x8 Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1208V3 Bedienungsanleitung

Kramer

Kramer VS-24x1 Bedienungsanleitung

Kramer

Kramer VS-88HD Bedienungsanleitung

Kramer

Kramer VS-5x5 Bedienungsanleitung

Kramer

Kramer VS-61YC Bedienungsanleitung

Kramer

Kramer VS-88UT Bedienungsanleitung

Kramer

Kramer VS-88UHD Bedienungsanleitung

Kramer

Kramer Sierra Video 6448V5Sxl Bedienungsanleitung

Kramer

Kramer 3232DEE Bedienungsanleitung

Kramer

Kramer 88DS Bedienungsanleitung

Kramer

Kramer VS-3232DN Bedienungsanleitung

Kramer

Kramer VS-42HN Bedienungsanleitung

Kramer

Kramer XL 3232VS Bedienungsanleitung

Kramer

Kramer VP-772 Bedienungsanleitung

Kramer

Kramer VS-211H Bedienungsanleitung

Kramer

Kramer VP-885 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung