Kramer VS-42H2 Bedienungsanleitung

VS-42H2 Quick Start (P/N: 2900-300947QS REV 1)

P/N:

2900- 300947QS

Rev:

Scan for full manual

VS-42H2 Quick Start Guide

This guide helps you install and use your VS-42H2.

Go to www.kramerav.com/manual/VS-42H2 to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check What’s in the Box

VS-42H2

4x2 HDMI Matrix Switcher

4 Rubber feet Infrared remote control transmitter

1 Power supply (5V DC)

1 Quick start guide

Step 2: Get to know your VS-42H2

# Feature Function

IR LED

Lights yellow when receiving an IR signal.

2 IR Sensor Receives signals from the infrared remote control transmitter.

ON LED

Lights green when the device is powered on.

4 INPUT SELECTOR

TO OUT 1, 1–4

Press one of the four inputs to switch it to OUT 1.

5 INPUT SELECTOR

TO OUT 2, 1–4

Press one of the four inputs to switch it to OUT 2.

6 MUTE OUT 2 Button Press to toggle mute of the OUT 2 signal.

MUTE OUT 1 Button

Press to toggle mute of the OUT 1 signal.

8 EDID Button Press to capture the EDID (see Step 6).

LOCK Button

Press and hold to lock the front panel buttons. Press and hold again to unlock.

# Feature Function

INPUT 1–4 HDMI Input Connectors

Connect to up to four HDMI sources.

11 REMOTE IR Opening Connect to an external IR receiver for controlling the device via an IR remote controller.

Covered by a cap. The 3.5mm mini jack at the end of the internal IR connection cable fits

into this opening.

12 REMOTE INPUT TO OUT 1

4-pin Terminal Block + Ground

Connect to up to four remote, contact-closure input selection switches for Output 1.

13 REMOTE INPUT TO OUT 2

4-pin Terminal Block + Ground

Connect to up to four remote, contact-closure input selection switches for Output 2.

RS-232 3-pin Terminal Block

Connect to a PC/serial controller.

15 SETUP 8-way DIP-Switch Sets the device configuration.

PROG VIA USB Connector

Connect to a PC to upgrade the firmware.

17 FACTORY PROG

VIA RS-232 Upgrade Switch

Press to upgrade the firmware via the RS-232 port, release for normal operation.

ETHERNET RJ-45 Connector

Connect to a PC via a LAN.

19 RESET Switch Press while power-cycling the device to reset to factory default parameters.

5V DC Connector

Connect to the power adapter, center pin positive.

21 OUT 1 and OUT 2 HDMI Output

Connectors

Connect to up to two HDMI acceptors.

Step 3: Install VS-42H2

Attach the rubber feet and place on a table or mount VS-42H2 in a rack (using an optional RK-T2B rack mount).

Step 4: Connect the inputs and outputs

Always

switch OFF the

power on each device

before connecting it to your

-42H2. For best results,

we recommend that you

always use Kramer high

performance cables to

connect AV equipment to

-42H2.

Connecting the remote input selection switches:

These remote switches replicate the input selection buttons on the front panel of VS-42H2.

Step 5: Connect the power

Connect the 5V DC power adapter to VS-42H2 and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power adapter that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operate VS-42H2

Operate VS-42H2 via:

•Front panel buttons

•Remotely, via RS-232 serial

commands transmitted by a touch

screen system, PC, or other serial

controller

•Remotely, using an IR remote

control transmitter

•Embedded web pages via the

Ethernet

•Contact-closure switches

RS-232 / Protocol 3000 Default Parameters

Baud Rate: 115,200

Data Bits: 8

Stop Bits: 1

Parity: None

Command Format:

ASCII

TCP/IP Default Parameters

IP Address: 192.168.1.39

Netmask: 255.255.0.0

Gateway: 0.0.0.0

TCP Port #: 5000

UDP Port #: 50000

Switch an input to an output:

•Press an input button on the top row (To OUT 1) to switch that input to Output 1.

•Press an input button on the bottom row (To OUT 2) to switch that input to Output 2.

Copy the EDID from an Output to one or more Inputs:

1. Press the EDID button to enter the EDID setting mode.

The EDID button lights.

Note: If there is no button activity for 10 seconds, the device automatically exits the EDID setting mode to normal operation, the EDID

button no longer lights and any changes made are lost.

2. From the To OUT 1 (top) row, press each of the Inputs to which you want to copy the EDID from Output 1.

Each selected Input LED lights.

3. From the To OUT 2 (bottom) row, press each of the Inputs into which you want to copy the EDID from Output 2.

Each selected Input LED lights.

4. Press the EDID button.

The button no longer lights and the EDID changes are saved.

Copy the default EDID to one or more Inputs:

1. Press the EDID button to enter the EDID setting mode.

The EDID button lights.

2. For each Input to which you want to copy the default EDID, press both the To OUT 1 and To OUT 2 buttons simultaneously.

Both top row and bottom row Input LEDs light.

3. Press the EDID button.

The button no longer lights and the EDID changes are saved.

Set the HDCP status for each input using the DIP-switches:

Note: Push the DIP-switch up for ON and down for OFF.

Switch # Description

1 OFF – Input 1 does not support HDCP

ON – Input 1 is HDCP compliant

2 OFF – Input 2 does not support HDCP

ON – Input 2 is HDCP compliant

3 OFF – Input 3 does not support HDCP

ON – Input 3 is HDCP compliant

4 OFF – Input 4 does not support HDCP

ON – Input 5 is HDCP compliant

Set the automatic switching mode for each output using the DIP-switches:

1. Use DIP-switch 5 (input 1) or 7 (input 2) to select manual or automatic switching for the output.

2. If automatic is selected, use DIP-switch 6 (input 1) or 8 (input 2) to select the automatic switching mode.

Note: Push the DIP-switch up for ON and down for OFF.

Switch # Description

5 OFF – Output 1: Manual switching

ON – Output 1: Automatic switching

6 OFF – Output 1: Last Connected mode

ON – Output 1: Priority mode

7 OFF – Output 2: Manual switching

ON – Output 2: Automatic switching

8 OFF – Output 2: Last Connected mode

ON – Output 2: Priority mode

Andere Handbücher für VS-42H2

Inhaltsverzeichnis

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer VS-3232V Bedienungsanleitung

Kramer

Kramer Sierra Video 4848V5xl Bedienungsanleitung

Kramer

Kramer VP-727XL Bedienungsanleitung

Kramer

Kramer VP-8x8TP Bedienungsanleitung

Kramer

Kramer VS-169TP Bedienungsanleitung

Kramer

Kramer VS-1616D Bedienungsanleitung

Kramer

Kramer 88DEE Bedienungsanleitung

Kramer

Kramer VS-88A Bedienungsanleitung

Kramer

Kramer VS-24x1 Bedienungsanleitung

Kramer

Kramer 3232HDS Bedienungsanleitung

Kramer

Kramer VP-26 Bedienungsanleitung

Kramer

Kramer 84V5 Bedienungsanleitung

Kramer

Kramer VS-162V Bedienungsanleitung

Kramer

Kramer VS-1616D-MD Bedienungsanleitung

Kramer

Kramer VP-8x8 Bedienungsanleitung

Kramer

Kramer Sierra Video 1204V5S Bedienungsanleitung

Kramer

Kramer VP-4x4K Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1608V5 Bedienungsanleitung

Kramer

Kramer VS-84H Bedienungsanleitung

Kramer

Kramer VS-4228 Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1208V5S Bedienungsanleitung

Kramer

Kramer VS-66H3 Bedienungsanleitung

Kramer

Kramer VS-6YC Bedienungsanleitung

Kramer

Kramer 88V3S Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung