Kramer VS-44H2 Bedienungsanleitung
VS-44H2 Quick Start
P/N:
2900- 301297QS
Rev:
1
Scan for full manual
VS-44H2 Quick Start Guide
This guide helps you install and use your VS-44H2 for thefirst time.
Go to www.kramerav.com/downloads/VS-44H2to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
VS-44H2 4K 4x4 Matrix Switcher
4 Rubber feet
1 Quick start guide
1 Set of rackears
1 Power cord
Step 2: Get to know your VS-44H2
#
Feature
Function
1
IN Select Buttons (1 to 4)
Press to select the input to switch after selecting an output (also used for storing
machine setups).
2
OUT Select Buttons (1 to 4)
Press to select an output to switch followed by an input.
3
MUTE/PATTERN Button
Press to view the current pattern status and select the output/s to which a pattern is
routed.
Press to mute audio and video on a selected output.
4
ALL Button
Press followed by an input button to connect the selected input to all outputs.
For example, press ALL and then Input button # 2 to connect input # 2 to all the
outputs.
5
STO Button
Press STO followed by an IN or OUT (1 to 4) button to store the current switching
configuration to the location corresponding to that INPUT number.
6
RCL Button
Press RCL followed by the corresponding IN or OUT (1 to 4) button to recall the
preset switching configuration saved in that location.
7
LOCK Button
Press and hold to toggle between locking and releasing the front panel buttons.
8
EDID Button
Press to enter the EDID mode.
9
OUTPUT/INPUT 7-segment LED
Display
Displays the input currently switched to the output which is marked above each input.
#
Feature
Function
10
HDMI™ IN Connectors (1 to 4)
Connect to up to 4 HDMI sources.
11
HDMI OUT Connectors (1 to 4)
Connect to up to 4 HDMI acceptors.
12
5V/2A USB Port
Use to charge a device.
13
PROG USB Mini port
Connect to a PC/serial controller to control the device.
14
Reset Button
Press and hold for about 8 seconds to reset IP settings to factory default values.
15
ETHERNET RJ-45 Connector
Connect to a PC via a LAN.
16
RS-232 9-pin D-sub Connector
Connect to a PC/serial controller to control the device.
17
Mains Power Connector Fuse
Plug in the power cord.
18
Power Illuminated Switch
Turn the device on and off.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Mount VS-44H2
To rack mount the machine, attach both rack ears
(by removing the screws from each side of the
machine and replacing those screws through the
rack ears) or place the machine on a table.
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VS-44H2. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VS-44H2.
Step 5: Connect power
Connect the power cord to VS-44H2 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection,located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.
Step 6: Operate the VS-44H2
Operate via RS-232 and Ethernet communication parameters:
RS-232/Ethernet
Baud Rate:
115,200
Parity:
None
Data Bits:
8
Command Format:
ASCII Protocol 3000
Stop Bits:
1
Example (route video HDMI IN 4 to video HDMI OUT 1):
“#X-ROUTE
OUT.HDMI.1.VIDEO.1,IN.HDMI.4.VIDEO.1”,0x0D
Ethernet Parameters
IP Address:
192.168.1.39
Default TCP Port #:
5000
Subnet Mask:
255.255.0.0
Default UDP Port #:
50000
Default Gateway:
192.168.0.1
Username/Password:
Admin/Admin
Full Factory Reset
Front panel:
There is no option for factory reset from front panel.
Protocol 3000:
“#factory” command.
Web Pages:
Device Settings page, Soft Factory Reset resets all parameters to factory default except for network
parameters.
Operate via Front Panel Buttons
Switch an input to an output via front panel buttons
Press an output button followed by an input button to switch the selected input to the selected output.
Switch an input simultaneously to all 4 outputs
1. Press ALL. All 4 outputs on the 7-segment display flash.
2. Press an input button. The selected input is routed to all the outputs.
Store a switching setting
1. Configure the switching as required for the preset.
2. Press STO. The STO button flashes.
3. Press an input or output button (1-4). The input or output button flashes
and the STO button stops flashing.
Recall a switching setting
1. Press RCL. The RCL button flashes.
2. Press the relevant input or output button that stored the preset.
Once the stored preset is recalled, the RCL button stops flashing.
Acquiring the EDID
Acquire EDID from:
•One output to one or more of the inputs.
•Different outputs to different inputs.
•The default EDID (by reading EDID from an output that is not connected to an acceptor).
To acquire an EDID from an output to one or more inputs:
1. Make sure that the output is connected to an acceptor.
2. Press EDID (short press). EDID button lights.
The 7-segment display shows the current EDID status.
3. Press one or more input buttons (to which the EDID is copied) or press ALL (to copy EDID to all the inputs).
The corresponding 7-segment LEDs flash.
4. Press the output button (from which the EDID is acquired).
The 7-segment LEDs show the output number from which the EDID is read.
5. Press and hold EDID until the device acquires the EDID and device exits EDID mode (EDID and STO button lights
turn off).
If the output is not connected to an acceptor, the 7-segment display shows “d”. When reading the EDID from
an unconnected output, the default EDID is restored.
Andere Handbücher für VS-44H2
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Kramer Matrix-Umschalter Handbücher
Kramer
Kramer Sierra Video 84V3 Bedienungsanleitung
Kramer
Kramer XL 1616S Bedienungsanleitung
Kramer
Kramer Cobra MX-1616 Bedienungsanleitung
Kramer
Kramer Sierra Video 4832V5Sxl Bedienungsanleitung
Kramer
Kramer VS-34FD Bedienungsanleitung
Kramer
Kramer Sierra Video 4848V5SXL Bedienungsanleitung
Kramer
Kramer VP-4x8 Bedienungsanleitung
Kramer
Kramer VS-62DT Bedienungsanleitung
Kramer
Kramer VS-44DT Bedienungsanleitung
Kramer
Kramer VS-1616DN-MD Bedienungsanleitung
Kramer
Kramer VS-88HDCPxl Bedienungsanleitung
Kramer
Kramer VP-8x8TP Bedienungsanleitung
Kramer
Kramer VS-1616AD Bedienungsanleitung
Kramer
Kramer VS-44HDCP Bedienungsanleitung
Kramer
Kramer VS-806YC Bedienungsanleitung
Kramer
Kramer Sierra Video 6448V5xl Bedienungsanleitung
Kramer
Kramer VP-81SID Bedienungsanleitung
Kramer
Kramer MTX3-16-M Bedienungsanleitung
Kramer
Kramer Sierra Pro XL 1208V3 Bedienungsanleitung
Kramer
Kramer VS-66HDCPxl Bedienungsanleitung
Beliebte Matrix-Umschalter Handbücher anderer Marken
AMX
AMX AVS-OP-2020-117 Anleitungen und Rezepte
Lindy
Lindy 38042 Bedienungsanleitung
Extron electronics
Extron electronics MTPX Plus Series Bedienungsanleitung
Key Digital
Key Digital Champion KD-16x16CS Bedienungsanleitung
Shinybow USA
Shinybow USA SB-8811 Bedienungsanleitung
Optimus
Optimus Compact Bedienungsanleitung