Kusam-meco KM-01 Bedienungsanleitung

G-17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct.: 022 -2 4156638, Tel. : 022-241224540, 24181649, Fax : 022 - 24149659

Email : [email protected], Website : www.kusamelectrical.com

An ISO 9001:2008 Company

All Specifications are subject to change without prior notice

Navin.com/D.drive/sandeep gupta/New catlog Dec 2011/KM-01,03,41,81

An ISO 9001:2008 Company

®ANALOG INSULATION RESISTANCE TESTER

Model KM-01/03/41/81

APPLICATIONS :

?Battery Operation

?Logarithmic Scale.

?Anti-parallax mirror scale for accurate readings.

?Power ON / OFF switch Lock for continuous measurement.

?Battery condition indication.

?Sturdy ABS case

?High Voltage (Output) LED Indicator

?Operating Temperature : 0°C-40°C, < 75%R.H.

?Storage Temperature : -10°C-60°C, < 80%R.H.

?Power ON/OFF Switch for continuous measurement

?AC Voltage measurement facility to check for live circuits.

?AC Voltage measurement Accuracy within ±5% of max. Scale value.

?Terminal- to- Terminal Voltage ± 10% of rated Voltage at "0" Megaohms scale.

About 90% of rated Voltage at Center scale.

?Insulation Resistance Accuracy ± 5% indicated value

?Power Supply :Standard 1.5V x 4 batteries.

?Dimensions : 100 X 150 X 45 mm. Appx.

?Weight : 350 gms. Approx

FEATURES :

ACCESSORIES :

Test Lead with probe x 1, test lead with clip x 1, Batteries, Carrying Case & User Manual.

?Insulation Test for general equipment & electronic components.

?Test for a high power equipment (e.g. high power apparatuses for cable & communications

apparatuses)

?Insulation Test for power equipment.

100 V 0 - 50 MW

500 V 0 - 100 MW

500 V 0 - 1000 MW

1000 V 0 - 2000 MW

KM - 01

KM - 03

KM - 41

KM - 81

MODEL NO. RATED OUTPUT V (DC) SCALE RANGE

0 - 600 V

ACV RANGE

ELECTRICAL SPECIFICATIONS - KM 01/03/41/81

Accuracy : ±% reading ± digits

Environment to guarantee accuracy : 23°C ± 5°C, less than 75% RH

CARRYING CASE

LOGARITHMIC SCALE.

Model - KM 01

Model - KM 03

Model - KM 41

DIGITAL INSULATION RESISTANCE TESTER

INSTRUCTION MANUAL

MODELS - KM - 01, KM - 03,

KM - 41, KM - 81

KM-81

No.1

INSULATION TESTER

G-17, Bharat Industrial Estate,

T.J.Road, Sewree (W), Mumbai - 400015. (INDIA)

Sales Direct: 24156638 Tel : 91-22-2412 4540, 2418 1649

Fax : 91-22-2414 9659

Email : [email protected]

Website :www.kusam-meco.co.in,

www.kusamelectrical.com

DIGITAL INSULATION

RESISTANCE TESTER

INSTRUCTION MANUAL

KM - 81

KM - 41

KM - 03

KM - 01

BATTERY - DRIVEN

INSULATION RESISTANCE TSTERS

Introduction

Thank you very much for purchasing this insulation

resistance tester. This is a small, easy-to-operate

insulation resistance tester using a transistor-type, stable

voltage type DC-DC converter. It enables the user to

read promptly and directly the insulation resistance value

of various electric equipment and lines.

1. A small, light-weight and easy-to operate product.

2. Used is a core-magnet type meter which is stable and

little influenced by external magnetic field.

3. It is economical since only four SUM-3 or R6 batteries

can drive the tester.

4. Incorporating the ACV range, it can measure the

voltage of AC line.

5. The measuring switch can be locked, so it is very

handy to make continuous measurements.

6. It incorporates an LED pilot lamp showing ON of high

voltage power sources (500V) and lighting

intermittently, so the user can know precisely whether

or not any voltage exists. It also helps the user avoid

forgetting to turn off the switch when it is locked.

Specifications

Model No. Rated V

Rated R Scale range ACV Usage

KM-81

1000V

2000MW

0-2000MW0-600V

General insulation tests.

Tests for a high power equipment

(e.g. high power apparatuses for cable

and communications apparatuses)

KM-41 500V

1000MW

0-1000MW0-600V

Insulation tests for general equipment

and electronic components

KM-03 500V

100MW

0-100MW0-600V

Insulation tests for general equipment,

chiefly power equipment.

KM-01 100V

50MW

0-50MW0-600V

Insulation tests for general equipment.

· ¥

Power source Standard (1.5v) X 4 batteries.

Accuracy Within ±5% of the scale length

Terminal-to-terminal ±10% of rated voltage ................. scale

voltage About 90% of rated voltage ............ Center scale

ACV Within ±5% of max. scale value

Size & Weight 150 X 100 X 45mm, About 350 g

Accessories Test lead with probe X1 Test lead with clip X1 carrying case

Frontal View and the Name of Parts

L Terminal (LINE side)

E Terminal (EARTH side)

Indicator

MWscale

ACV scale

Pointer

position adjuster

Control switch

Insulation resistance

push switch

Pilot lamp for high

power source

Rear case

BATT check scale

Connection plug

Test lead with probe

Test lead with clip

KM-81

No.1

INSULATION TESTER

1. Connection of Test Leads Connect the test lead

with probe to the L terminal and the test lead with

clip to the E terminal as shown in Figure 1.

lHow to Use KM-81, KM-41, KM-03, KM-01

KM-81

No.1

INSULATION TESTER

2. Adjustment of Infinity ( ) Scale ... Confirmation

Align the pointer to the infinity line, leftmost of the

MW, scale, by turning the position adjuster in

the center of the indicator, if it doesn't point to it

correctly.

¥ 7

3. Measurement of Insulation Resistance

3-1 Connect the clip to one side of the measured object

and the probe to the other side of the measured

object.

3-2 Turn the control switch from POWER OFF position,

to MWposition and push on PUSH switch , then

the indicator shows the insulation resistance value.

3-3 If the pilot lamp of 500V ON below of the scale

plate, lights intermittently, the tester works properly and

the voltage is correctly impressed on the test point. It

doesn't light, however, if the internal batteries have

worn out or the battery contact is incomplete.

3-4 Set the control switch to MWPOWER LOCK

position for continuous measurements. POWER

switch remains ON regardless of PUSH switch. (The

pilot lamp lights intermittently.)

3-5 Return the control switch to POWER OFF position

after measurement.

4. Check of Internal Batteries.

Set the control switch to BATT CHECK position with

the E and L terminals released.

If the pointer automatically swings to the BATT

scale , both circuit and the internal batteries are

normal. If the pointer points to the left side of the BATT

scale as shown in Fig.2, the batteries have worn out.

Replace them with new batteries. For replacement of

the batteries, refer to page 7.

BATT

Fig.2

4 5

Replacement of Battery

When replacing battery, loosen the 4 X 15 screw on the

rear case, remove the case, and insert the new batteries

correctly with the right polarity as shown in Fig.3.

Batteries 1.5V 4pcs.

Fig. 3

5. ACV Measurement

5-1 Connection of the test leads is same as in the

foregoing paragraph.

5-2 Use the control switch in ACV (POWER OFF)

position.

5-3 Connect the lead line tip to the measured point and

read the voltage value in the red 0~600V scale

5-4 This ACV range can be used not only for general

ACV measurements but also for a preliminary

check as to whether or not ACV is impressed on

the measured object, prior to insulation resistance

measurement.

Be sure to return the control switch to POWER OFF

position after use. With the control switch to this

position, the current doesn't flow and the batteries

are protected from being exhausted for nothing

even if the measuring push switch is inadvertently

pushed on.

Precaution

lPrecaution for Use

1. E and L Terminals

When the minus side of the measured object is

grounded, plug the test lead into the E terminal.

Make measurement with the E terminal test lead

connected to the ground side. By so doing it is

common that the measured value is indicated at a

smaller value. Safety in use is considered and

promised. For general measurements, use either

polarity of the terminals.

2. If the tester is not used for a long time, be sure to

take out the internal batteries.

3. Don't store the tester in a high temperature and

humidity.

4. Avoid giving any mechanical shock or vibration to

the tester.

5. Don't rub strongly the surface of the indicator cover

with a dry cloth. Should anti-static coating on the

cover be removed, a cloth moistened with anti-static

solvent should be used to clean the cover.

MUMBAI

TEST CERTIFICATE

DIGITAL INSULATION

RESISTANCE TESTER

This Test Certificate warrantees that

the product has been inspected and

tested in accordance with the published

specifications.

The instrument has been calibrated by

using equipment which has already

been calibrated to standards traceable

to national standards.

MODEL NO. ___________

SERIAL NO. ___________

DATE: ___________

ISO 9001

REGISTERED

PASS

KUSAM-MECO

Each “KUSAM-MECO” product is warranted to be free

from defects in material and workmanship under normal

use & service. The warranty period is one year (12

months) and begins from the date of despatch of goods.

In case any defect occurs in functioning of the instrument,

under proper use, within the warranty period, the same

will be rectified by us free of charges, provided the to and

fro freight charges are borne by you.

This warranty extends only to the original buyer or end-

user customer of a “KUSAM-MECO” authorized dealer.

This warranty does not apply for damaged Ic’s, burnt

PCB’s, fuses, disposable batteries, carrying case, test

leads, or to any product which in “KUSAM-MECO’s”

opinion, has been misused, altered, neglected,

contaminated or damaged by accident or abnormal

conditions of operation or handling.

“KUSAM-MECO” authorized dealer shall extend this

warranty on new and unused products to end-user

customers only but have no authority to extend a greater

or different warranty on behalf of “KUSAM-MECO”.

“KUSAM-MECO’s” warranty obligation is limited, at

option, free of charge repair, or replacement of a

defective product which is returned to a “KUSAM-MECO”

authorized service center within the warranty period.

WARRANTY

Service Centre:

G-17, Bharat Industrial Estate,

T.J.Road, Sewree (W), Mumbai - 400015. (INDIA)

Sales Direct: 24156638 Tel : 91-22-2412 4540, 2418 1649

Fax : 91-22-2414 9659 Email : [email protected]

Website :www.kusam-meco.co.in, www.kusamelectrical.com

THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE

REMEDY AND IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF

M E R C H A N TA B I L I T Y O R F I T N E S S F O R A

PARTICULAR PURPOSE. “KUSAM-MECO” SHALL

NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

LOSSES, INCLUDING LOSS OF DATA, ARISING FROM

ANY CAUSE WHATSOEVER.

All transaction are subject to Mumbai Jurisdiction.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kusam-meco Messgerät Handbücher

Kusam-meco

Kusam-meco KM 63A Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8042 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 072 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 907 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 078 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 061 Bedienungsanleitung

Kusam-meco

Kusam-meco CA 3000 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 3060 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2234BL Bedienungsanleitung

Kusam-meco

Kusam-meco KM 63 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8041 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 035 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 981 MK-1 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 076 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 711 Bedienungsanleitung

Kusam-meco

Kusam-meco 954 MK-II Bedienungsanleitung

Kusam-meco

Kusam-meco 2700 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 039F Bedienungsanleitung

Kusam-meco

Kusam-meco KM 1002 Bedienungsanleitung

Kusam-meco

Kusam-meco 9999 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 088 Bedienungsanleitung

Kusam-meco

Kusam-meco 108 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2784-T Bedienungsanleitung

Kusam-meco

Kusam-meco KM 175D Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung