Kusam-meco KM 117A Bedienungsanleitung

®®

AN ISO 9001:2008 COMPANY

MODEL - KM 117A

DIGITAL COATING

THICKNESS GAUGE

OPERATION MANUAL

G 17, Bharat Industrial Estate, T. J. Road,

Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct : (022) 24156638

Tel. : (022) 24124540, 24181649. Fax : (022) 24149659

Email : [email protected]

Website : www.kusamelectrical.com

www.kusam-meco.co.in

LIST OF PRODUCTS

¬Digital Multimeter ¬Digital AC & AC/DC Clampmeter

¬AC Clamp Adaptor ¬AC/DC Current Adaptor

¬Thermo Anemometer ¬Thermo Hygrometer

¬Distance Meter ¬Digital Lux Meter

¬Network Cable Tester ¬Power Factor Regulator

¬Earth Resistance Tester ¬Digital Panel Meters

¬DC Power Supplies ¬High Voltage Detector

¬Calibrators ¬Gas Analysers

¬Frequency Counter ¬Function Generator

¬Phasing Sticks ¬Battery Tester

¬Waterproof Pen Testers ¬Solar Power Meter

¬EMF Detector

¬Wood, Paper & Grain Moisture Meter

¬Transistorised Electronic Analog & Digital Insulation

Resistance Testers(upto 10 KV)

¬Digital Sound Level Meter & Sound Level Calibrator

¬Digital contact & Non-contact Type Tachometer

¬Digital Non-contact (infrared) Thermometer

¬Maximum Demand Controller/Digital Power Meter

¬Digital Hand Held Temperature Indicators

® ®

DIGITAL COATING

THICKNESS GAUGE

MODEL - KM 117A

TABLE OF CONTENTS

TITLE PAGE NO.

I. .................................

II. Features.......................................................

VI.

Introduction................

III. Safety Information......................................

V. Product Use................................................

Maintenance

VIII. Test Certificate...........................................

IX. Warranty......................................................

IV. Specifications.............................................

Measurements............................................

VII. ...............................................

® ®

I. INTRODUCTION :

KM 117A is a ferrous coating thickness gauge designed for simply

one hand operation.

II. FEATURES :

1. LED backlight.

2. LCD display reverse.

3. Auto power off.

4. Low-battery indicator.

5. Calibration for normal use.

6. Data logging function.

7. Warning beeper triggers by hi/lo limit settings.

8. Inch and Metric measurement options.

9. Zeroing Plate and Standard Coating Plate.

10. Attached with carrying strap.

11. Soft carrying case.

III. SAFETY INFORMATION :

It is recommended that you read the safety and operation instructions

before using the coating thickness gauge.

1. CAUTION :

1. Do not use the unit near any device which

generates strong electromagnetic radiation

or near a static electrical charge, as these

may cause errors.

2. Do not use the unit where it may be

exposed to corrosive or explosive gases.

The unit may be damaged, or explosion

may occur.

3. Do not keep or use this unit in an environment where it will be

directly illuminated by sunshine, or where it condensation. If

you do, it may be deformed, its insulation may be damaged, or

it may no longer function according to specification.

4. Do not place the meter on or around hot objects (70°C/158°F).

It may cause damage to the case.

5. If the meter is exposed to significant changes in ambient

temperature, allow 30 minutes for temperature stabilization,

before taking measurement.

6. Condensation may form on the sensor when going from a cold

to hot environment. Wait for 10 minutes for condensation to

dissipate before taking measurements.

7. This unit is not constructed to be waterproof

and dustproof. Do not use it in a wet or very

dusty environment.

8. In order to take accurate measurement, make

sure the sensing tip contacts the coated

surface tightly without tilting.

9. Please make sure there is no air bubbles

between substrate and coating.

10.Substrate zeroing calibration must be implemented for

each use.

11. Two point calibration is suggested to implement for

frequent testing points to increase measuring accuracy.

® ®

2. WARNING :

A. Electromagnetic Field Interference :

This instrument uses magnetic field method to measure the

coating thickness on ferrous metal base. If this meter was placed

in the environment with 20mG (mini Gauss) or above, the accuracy

would be affected. Suggest that the meter should to put far away

from the interfered source at least 30cm.

B. Electromagnetic Field Strength : (µunit = mini Gauss)

Electromagnetic Source

Cellular Phone Charger

Notebook Power Supply

LCD Display

Fan

Reading Lamp

µAny product with coil inside should be considered.

0cm

50 ~ 500

100 ~ 1000

10 ~ 100

100 ~ 1000

400 ~ 4000

30cm

< 1

< 5

< 1

< 5

< 10

Recommended operating conditions (> 30cm)

Fe mm

i00

102 ± 2 micron

ADAPTOR

Fe mm

i00

Abnormal operating conditions (< 30cm)

102 ± 2 micron

ADAPTOR

768

Fe mm

i25

Fe mm

i25

® ®

IV. SPECIFICATIONS :

1. General Specifications :

Operating : 0°C~50 C (32 F to 122 F) at < 75% RHTemperature ° ° °

Storage Temperature : -20°C~60°C (-4°F to 140°F) at < 80% RH

(with battery removed)

Temperature Coefficient : Nominal 0.1 x (specified accuracy)/ °C

@ (< 18°C or > 28°C)

Standby Consuming Current : < 6mA.

Auto Power Off : 30 seconds.

Power Supply : 1.5V (AAA Size) Battery X 2

Battery Life : 32 hours continuity use typical alkaline.

Low Battery Indication : The “ ” is displayed when the battery

drops below the operating level.

Dimension : 105(H) x 55(W) x 27(D)mm

Weight : Approx. 80 g (Including battery).

Accessories : User Manual, Battery & carrying case.

2. Electrical Specifications :

Detectable Substrate Material : Ferrous metal (iron, steel).

Thickness Range : 0 ~ 80.0mils (0 ~ 2000mm).

Display Resolution : 0.1mils/1mm.

Accuracy : ±4dgts on 0 to 7.8mils

±(3%+4dgts) on 7.9mils to 39.0mils

±(5%+4dgts) on 39.1mils to 80mils

±10dgts on 0 to 199mm

±(3%+10dgts) on 200mm to 1000mm

±(5%+4dgts) on 1001mm to 1999mm

Response Time : 1 second.

V. PRODUCT USE :

1. Definition :

Zeroing Plate Standard Coating Plate

Standard Thickness :

39.6 mils

1006 micron ± 1%

Peel off the

both side of

protection film

before use

µPeel off the protection films from foil before first use.

2. The Product :

Fe mm

MAX - MIN mils

888

8888

AVG CAL

MEM

SET

LCD

Function

Key

Sensing

Tip

Fe mmmils

BASE>2S

> 2S DEL

ESC

ZERO

® ®

BASE>2S

> 2S DEL

ESC

ZERO

3. Buttons :

Buttons Function

> 2S

DEL

ESC

Press the button to enter MENU/ selecting.

Press the button to reverse the display.

Press the button for 2 seconds to turn on

or off backlight.

Jumped off & return of the previous mode.

Up/down adjusting, (select function-value)

Press the button to substrate Zeroing calibration.

Press the button for 2 seconds to clear Calibrating

Point.

BASE>2S

ZERO

µDuring measure mode :

DEL

ESC The three buttons are disabled.

µDuring setting mode :

The two buttons are disabled.

> 2S

BASE>2S

ZERO

4. The Display :

Fe mm

MAX - MIN mils

888

8888

AVG CAL

MEM

Fe mmmils

No. Symbol Meaning

MAX

MIN

MAX - MIN

AVG

CAL

mm, mils

Ferrous

Maximum reading

Minimum reading

Maximum - Minimum reading

Average reading

Number of the reading

Low battery

Alarm indicator

Record is activated

Calibration is activated

Measurement units

MEM

1. Auto Power Off (APO) :

Leave the gauge without operation for 30 seconds, power turns off

automatically.

µDuring set mode, Auto Power Off function will be inactivated.

Measuring :

1. Gauge automatically powers up and Measuring when probe is

pressed.

2. Put the probe to contact coated surface tightly, wait for the

reading to appear and measurement is completed. (One sound

“Beep” announced)

3. If the coating thickness is out of range, the meter shows “----”.

CAUTION :

Keep the sensing tip of the meter away from any substrate or

any magnetic field.

4. When the alarm is activated, measured exceed “Hi Limits” or

“Lo Limits”, LCD display (updated) the measured value will be lit

up along with pressing or symbol, the beeper emits a

continuous or pulsed tone, warm users exceeds the Hi or Lo

Limits value.

2. Menu :

VI. MEASUREMENTS :

In measuring mode, press button to enter menus, will blink.CAL

With and button to select the function, browse the menus :

CAL

Two Point Calibration

Record Setting/Recall

Alarm Setting

Measurement Units

CAL

Two Point Calibration :

® ®

µDuring two point calibration, the foil and standard coating

plate 1006mm can be replaced by uncoated substrate and a

standard coating plate with known-thickness.

µWhen it is calibrated by user, its max calibrated value is

1100mm (43.3 mils),

Fe mm

CAL

In this mode, press button to enter two point

calibration.

Fe mm

CAL

Into “low” value adjustments of the two point

calibration, press or button to adjust

reading, when it displays the desired value,

press button to confirm.

Fe mm

push

CAL

Press the tip of the Gauge to contact coated

surface tightly (Zeroing plate or uncoated

substrate). Wait for one “Beep” sound announces.

Fe mm

1006

CAL

Into “Hi” value adjustments of the two point

calibration, press or button to adjust

reading, when it display the desired value,

press button to confirm.

Press the tip of the Gauge to contact coated

surface tightly (Standard coating plate 1006mm or

standard coating plate), wait for one “Beep” sound

announces, exit two point calibration and return to

measuring mode.

Fe mm

push

CAL

Before users finish two point calibration, if press button to exit

two point calibration, since the calibration is not finished, it will not

record its previous calibrated value.

DEL

ESC

Record Setting/Recall :

The product can record 255 samples.

Stop recording after the 255th measured value.

In this mode, press button to enter recording

setting.

Fe mm

Press or button to select the record on or

off.

Fe mm

MEM

After it’s selected, press button to confirm.

Fe mm

off

A. Recalling previous records :

To exit this mode, press button. Press or

button to browse previous records, its

sequence as follows :

MAX

MIN

MAX-MIN

AVG

(Maximum reading)

(Minimum reading)

(Maximum - Minimum reading)

(Average reading)

Number of the recorded data

The first data

The 255th data

B. To delete all recorded data :

Fe mm

Press button for five seconds.

Press or button to select the delete or

yes

, press button to return to browse previous

records.

yes

, press button to delete record and return

to the measuring mode.

Fe mm

MEM

MAX

Alarm Setting :

Fe mm

In this mode, press button to enter the “Hi

Limits” alarm setting mode.

Fe mm

Press or button to turn on or off the “Hi

Limits” alarm.

After it’s selected, press button to enter the

“Hi Limits value” alarm setting mode.

off

Fe mm

2000

Press or button to adjust reading. When

it displays the desired value, press button to

confirm the “Hi Limits” alarm, and enter the “Lo

Limits” alarm mode setting.

® ®

Press or button to turn on or off the “Lo

Limits” alarm.

After it’s selected, press button to enter the

“Lo Limits value” setting.

off

Press or button to adjust reading, to meet

the desired value, press button to confirm the

“Hi Limits” alarm, and return to measuring mode.

Alarm setting : Maximum is 2000mm (78.7 mils), Minimum is 0 m

(0 mils).

Unit Selecting :

In this mode, press button to enter to unit

selecting.

Fe mm

Press or button to select the mm or mils.

After it’s selected, press button to exit the

unit selecting and return to measuring mode.

mils

Inhaltsverzeichnis

Andere Kusam-meco Messgerät Handbücher

Kusam-meco

Kusam-meco 108 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8041 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-LUX-200K Bedienungsanleitung

Kusam-meco

Kusam-meco KM 181 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8042 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2820EL Bedienungsanleitung

Kusam-meco

Kusam-meco KM 711 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 3060-T Bedienungsanleitung

Kusam-meco

Kusam-meco KM 078 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 076 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 035 Bedienungsanleitung

Kusam-meco

Kusam-meco 9999 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 072 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2805 MK-1 Bedienungsanleitung

Kusam-meco

Kusam-meco 2700 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 503 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 1002 Bedienungsanleitung

Kusam-meco

Kusam-meco 500HP Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2720 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-2006 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 63A Bedienungsanleitung

Kusam-meco

Kusam-meco CA 3000 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2008A Bedienungsanleitung

Kusam-meco

Kusam-meco KM 907 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung