Kusam-meco KM-CAL-906 Bedienungsanleitung

us or visit our web ( see the bottom page of the Manual ) .

Standard

Accessories

Make sure that the package contains all the accessories listed below. And if you find they are damaged or any

of them is missing, please contact the vendor from which you purchased the product as soon as possible.

Refer to the replacing part list in 15.3 in the Manual if you want to order the replacing parts.



One set of Industrial testing Lead （CL727220 ）



set of T esting Lead （Tp727110 ）



set of Alligator clip （CC807130 ）



quick reference guide



User's Manual



One Fuse 50mA/250V

Safety

Information

For the correct and safe use of the instrument, be sure to follow the cautionary notes stated in this manual

whenever handling the instrument. The Company shall not be held liable for any damage resulting from use of

the instrument in a manner other than prescribed in the cautionary notes.

Warning

identifies conditions and actions that pose hazards to the user; a Caution

Caution

identifies conditions

and actions that may damage the meter

the equipment under test.

Refer to

Table

1 for the explanation of the international electric symbols adopted by the calibrator

the user ’ s

manual.

Table

1 Explanations of International Electrical Symbols

Warning

avoid possible electric shock

personal injury:

Do not apply more than the rated voltage, as marked on the calibrator , between terminals

between any

terminal and earth ground;

Before use, verify the meter ’ s operation by measuring a known voltage;

Follow all equipment safety procedures ;

Do not use the meter if it is damaged. Before using the meter, inspect the case. Look for cracks

missing

plastic .Pay particular attention to the insulation surrounding the connectors;

Select the proper function and range for the measurement;

Make sure the battery door is closed and latched before operating the meter;

Remove test leads from the meter before opening the battery door;

Inspect the test leads for damaged insulation

exposed metal. Check test lead continuity. Replace

damaged test leads before using the meter;

When using the probes, keep fingers behind the finger guards on the probes;

Connect the common test lead before connecting the live test lead. When disconnecting test leads,

disconnect the live test lead first;

Do not use the meter if it operates abnormally. Protection may be impaired. When in doubt, have the

meter inspect;

EARTH GROUND

WARNING

INFORMATION



Do not operate this instrument in areas where inflammable

explosive gases

vapor exists. It is

extremely hazardous to use the instrument under such environments ;

Do not operate the meter around explosive gas, vapor,

dust;



Use only type 4 AAA batteries, properly installed in the meter case, to power the meter;



Do disconnect the testing lead before shifting to different source

measurement functions;



When servicing the meter, use only specified replacement parts.



avoid false reading, which could lead to possible electric shock

personal injury, replace the batteries

as soon as the low battery indicator ( ) appears .

Caution

avoid possible damage to meter

to equipment under test:



Disconnect the power and discharge all high-voltage capacitors before testing resistance

continuity.



Use the proper jacks, function s, and ranges for the measurement

source operation.

Familiar

With

the

Calibrator

Figure 1 Entire Graph

5.1

Measurement/

Source

Terminals

Figure 2 shows the measurement /source terminals of the calibrator.

Table

2 explains their use.

Figure 2 Measurement/ Source Terminals Figure 3 keys

Table

2 Measurement / Source Terminals

Terminal

Function

①

4W terminals : measurement terminal of the 4W OHM 、

RTD

②

Measurement Signals （+）： OHM 、RTD

③

Measurement Signals （+）： DC V 、TC

3W Terminal ：measurement terminal of the 3W OHM 、

RTD

5.2

Keys

Figure 3 shows keys of the calibrator.

Table

3 explains their use.

Table

3 Functions of the keys

④

All the common (return ) （-）terminals of measurement

function

⑤

Source Signals ：（ +）DC V 、TC

⑥

Source Signals ：（ -）OHM 、RTD

⑦

All the common (return ) （-

）

terminals of source functio n

⑧

Source Signal ：（ +）OHM 、RTD

No.

Name

Function

1~5

Source value set key

Increment of source set point

6~10

Source value set key

Decrement of source set point

MEASURE

key

Turn on or off measurement function

SOURCE

key

Turn on or off source function

Power key

Turn on or off the power

Backlight key

Turn on or off the backlight

Key

Select measurement/source DC-voltage function

RTD

Key

Select measurement/source RTD function

OHM

Key

Select measurement/source OHM function

Key

Select measurement/source Tc function

Key

Select measurement continuity function

RANGE

Key

Select measurement/source range

RJ-ON

Key

In TC measurement /source function, turn on or off the RJ

compensation function.

T.DISP

Key

In TC/RTD measurement /source function , pressing the

key, convert the assistance display between room

temperature or mV/ Ωvalue;

On other measurement /source function, pressing the key,

turn on or off room temperature display in assistance

display.

HOLD

Key

Measured value holding

4/3/2W

Key

In ohm/RTD measurement function, select 2W,3W or 4W

method .

AVG

Key

M easuring average value

ZERO

Key

Set the source value to default value

Inhaltsverzeichnis

Andere Kusam-meco Messgerät Handbücher

Kusam-meco

Kusam-meco KM 8041 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 072 Bedienungsanleitung

Kusam-meco

Kusam-meco 2781 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 1001 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 4235ER Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2783 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 711 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 8042 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 1002 Bedienungsanleitung

Kusam-meco

Kusam-meco CA-1000 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2820EL Bedienungsanleitung

Kusam-meco

Kusam-meco KM 086 Bedienungsanleitung

Kusam-meco

Kusam-meco 9999 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 117A Bedienungsanleitung

Kusam-meco

Kusam-meco KM 181 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2784-T Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2775 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-804 Bedienungsanleitung

Kusam-meco

Kusam-meco KM-CAL-802 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2008 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 033 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2780 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2009 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 2720 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung