KYMCO SUPER8 50 Bedienungsanleitung
S
UPER8 50
PREFACE
This Service Manual describes the
technical features and servicing
procedures for the KYMCO SUPER8 50
Section 1 contains the precautions for all
operations stated in this manual. Read
them carefully before starting any
operation.
Section 2 is the removal/installation
procedures for the frame covers which
are subject to higher removal/installation
frequency during maintenance and
servicing operations.
Section 3 describes the inspection/
adjustment procedures, safety rules and
service information for each part, starting
from periodic maintenance.
Sections 6 through 17 give instructions
for disassembly, assembly and inspection
of engine, chassis frame and electrical
equipment.
Most sections start with an assembly or
system illustration and troubleshooting
for the section. The subsequent pages
give detailed procedures for the section.
KWANG YANG MOTOR CO., LTD.
OVERSEAS SALES DEPARTMENT
OVERSEAS SERVICE SECTION
TABLE OF CONTENTS
GENERAL INFORMATION
1
FRAME COVERS/EXHAUST MUFFLER
2
INSPECTION/ADJUSTMENT
3
LUBRICATION SYSTEM
4
FUEL SYSTEM
5
ENGINE REMOVAL/INSTALLATION
6
CYLINDER HEAD/VALVES
7
CYLINDER/PISTON
8
ENGINE
DRIVE AND DRIVEN PULLEYS/KIC
K
STARTER
9
FINAL REDUCTION
10
CRANKCASE/CRANKSHAFT
11
FRONT WHEEL/FRONT BRAKE/
FRONT SUSPENSION
12
CHASSIS
REAR WHEEL /REAR BRAKE /REAR
SUSPENSION
13
BATTERY/CHARGING SYSTEM/A.C.
GENERATOR
14
IGNITION SYSTEM
15
STARTING SYSTEM
16
LIGHTS/INSTRUMENTS/SWITCHES
17
ELECTRICAL
EQUIPMEN
T
EXHAUST EMISSION CONTROL
SYSTEM
Our company reserves the right to make
any alteration in the design.
The
information and contents included in
this manual may be different from the
motorcycle in case specifications are
changed.
18
1. GENERAL INFORMATION
1-1
SUPER8 50
Location of Engine Serial Numbe
r
Frame Serial Numbe
r
1
ENGINE SERIAL NUMBER
1
ENGINE SERIAL NUMBER...................1- 1 LUBRICATION POINTS .......................1-13
SPECIFICATIONS ...................................1- 2 CABLE & HARNESS ROUTING............1-15
SERVICE PRECAUTIONS......................1- 3 WIRING DIAGRAM................................1-20
TORQUE VALUES..................................1-11 TROUBLESHOOTUNG ..........................1-21
SPECIAL TOOLS.....................................1-12
1. GENERAL INFORMATION
1-2
SUPER8 50
SPECIFICATIONS
Motorcycle Name & Type SUPER8 50
Name & Model No. LEJ2
Overall length (mm) 1940
Overall width (mm) 745
Overall height (mm) 1220
Wheel base (mm) 1365
Engine type O.H.C.
Displacement 50cc
Fuel Used 92# nonleaded gasoline
Front wheel 43
Net weight (kg) Rear wheel 55
Total 108
Front wheel 45
Gross weight(kg) Rear wheel 67
Total 144
Front wheel 100/80 -14 56J
Tires Rear wheel 120/80 -14 56J
Ground clearance (mm) 112
Perform- Braking distance (m) 4 (Initial speed
20km/h)
ance Min. turning radius (m) 1.99
Starting system Starting motor &
kick starter
Type Gasoline, 4-stroke
Cylinder arrangement Single cylinder
Combustion chamber type Semi-sphere
Valve arrangement O.H.C.
Bore x stroke (mm) φ39.0 x 41.4
Compression ratio 11
Compression pressure
(kg/cm²-rpm) 18
Max. output 2.4/7500kw/(r/min)
Max. torque 3.2/7000kg m/rpm
Open 3°
Port Intake Close 7°
Engine
timin
g
Open 9°
Exhaust Close 1°
Valve
clearance Intake 0.08
(cold) (mm) Exhaust 0.08
Idle speed (rpm) 1900±100rpm
Lubrication type Forced
p
ressure &
wet sump
Oil pump type Inner/outer rotor type
Oil filter type Full-flow filtration
Lubrication
System
Oil capacity 0.8 liter
Cooling Type Forced air cooling
Air cleaner type & No Paper element, wet
Fuel capacity 6.0 liter
Type CVK
Piston dia. (mm) 18
Venturi dia.(mm) φ18.5equivalent
Carburetor
Throttle type Butterfly type
Type CDI
Ignition timing BTDC28°/4000rpm
Contact breaker Non-contact point type
Spark plug NGK CR7HSA
Spark plug gap 0.6～0.7mm
Battery Capacity 12V7AH
Clutch Type Dry multi-disc clutch
Type Non-stage transmission
Operation Automatic centrifugal
type
Type Two-stage reduction
Reduction 1st 0.8-3.1
ratio 2nd 11.05
Front Caster angle 27°
Axle Trail length ⎯
Tire
p
ressure Fron
t
1.75
(kg/cm²)Rear 2.25
Turning Left 45°
angle Right 45°
Fron
t
DISK
(
180mm
)
brake
Brake system
type Rear Drum (110mm) brake
Fron
t
TELESCOPE
Suspension type Rear Unit Swing
Front 80
Shock absorber
distance Rear 82
Frame type Under Bone
Fuel S
y
stem Electrical Equipment
I
g
nition S
y
stem
Power Drive System
Transmis-
sion Gear Reduction
Gear
Moving Device Damping
Device
1. GENERAL INFORMATION
1-3
SUPER8 50
SERVICE PRECAUTIONS
Make sure to install new gaskets, O-rings,
circlips, cotter pins, etc. when
reassembling.
When tightening bolts or nuts, begin with
larger-diameter to smaller ones at several
times, and tighten to the specified torque
diagonally.
Use genuine parts and lubricants
.
When servicing the motorcycle, be sure to
use special tools for removal and
installation.
After disassembly, clean removed parts.
Lubricate sliding surfaces with engine oil
before reassembly.
1. GENERAL INFORMATION
1-4
SUPER8 50
Apply or add designated greases and
lubricants to the specified lubrication
points.
After reassembly, check all parts for proper
tightening and operation.
When two persons work together, pay
attention to the mutual working safety.
Disconnect the battery negative (-) terminal
before operation.
When using a spanner or other tools, make
sure not to damage the motorcycle surface.
After operation, check all connecting
points, fasteners, and lines for proper
connection and installation.
When connecting the battery, the positive
(+) terminal must be connected first.
After connection, apply grease to the
battery terminals.
Terminal caps shall be installed securely.
1. GENERAL INFORMATION
1-5
SUPER8 50
If the fuse is burned out, find the cause and
repair it. Replace it with a new one
according to the specified capacity.
After operation, terminal caps shall be
installed securely.
When taking out the connector, the lock on
the connector shall be released before
operation.
Hold the connector body when connecting
or disconnecting it.
Do not pull the connector wire.
Check if any connector terminal is bending,
protruding or loose.
Confir
m
Capacity
1. GENERAL INFORMATION
1-6
SUPER8 50
The connector shall be inserted
completely.
If the double connector has a lock, lock
it at the correct position.
Check if there is any loose wire.
Before connecting a terminal, check for
damaged terminal cover or loose
negative terminal.
Check the double connector cover for
proper coverage and installation.
Insert the terminal completely.
Check the terminal cover for proper
coverage.
Do not make the terminal cover opening
face up.
Secure wire harnesses to the frame with
their respective wire bands at the
designated locations.
Tighten the bands so that only the insulated
surfaces contact the wire harnesses.
Sna
pp
in
g
!
1. GENERAL INFORMATION
1-7
SUPER8 50
After clamping, check each wire to make
sure it is secure.
.
Do not squeeze wires against the weld or
its clamp
After clamping, check each harness to
make sure that it is not interfering with any
moving or sliding parts.
When fixing the wire harnesses, do not
make it contact the parts which will
generate high heat.
Route wire harnesses to avoid sharp edges
or corners. Avoid the projected ends of
bolts and screws.
Route wire harnesses passing through the
side of bolts and screws. Avoid the
projected ends of bolts and screws.
N
o Contact !
1. GENERAL INFORMATION
1-8
SUPER8 50
Route harnesses so they are neither
pulled tight nor have excessive slack.
.
Protect wires and harnesses with electrical
tape or tube if they contact a sharp edge or
corner
When rubber protecting cover is used to
protect the wire harnesses, it shall be
installed securely.
Do not break the sheath of wire.
If a wire or harness is with a broken sheath,
repair by wrapping it with protective tape
or replace it.
When installing other parts, do not press or
squeeze the wires.
Do not pull
too ti
g
ht!
Do not press o
r
s
q
ueeze the wire.
1. GENERAL INFORMATION
1-9
SUPER8 50
After routing, check that the wire harnesses
are not twisted or kinked.
Wire harnesses routed along with
handlebar should not be pulled tight, have
excessive slack or interfere with adjacent
or surrounding parts in all steering
positions.
When a testing device is used, make sure to
understand the operating methods
thoroughly and operate according to the
operating instructions.
Be careful not to drop any parts.
When rust is found on a terminal, remove
the rust with sand paper or equivalent
before connecting.
Do not bend or twist control cables.
Damaged control cables will not operate
smoothly and may stick or bind.
Do you understand
the instrument? Is
the instrument set
correctly?
Remove Rust !
Andere Handbücher für SUPER8 50
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere KYMCO Roller Handbücher
KYMCO
KYMCO Like 200i Bedienungsanleitung
KYMCO
KYMCO PEOPLE S 125 Bedienungsanleitung
KYMCO
KYMCO SCOOTER MOD DJ Bedienungsanleitung
KYMCO
KYMCO Super 8 50 Bedienungsanleitung
KYMCO
KYMCO LIKE 150i Bedienungsanleitung
KYMCO
KYMCO 50 AGILITY RS NAKED 2T Bedienungsanleitung
KYMCO
KYMCO People GT 300i Bedienungsanleitung
KYMCO
KYMCO Agility Bedienungsanleitung
KYMCO
KYMCO Vitality 50 Bedienungsanleitung
KYMCO
KYMCO Super 9 50 Bedienungsanleitung
KYMCO
KYMCO Super 8 50 Bedienungsanleitung
KYMCO
KYMCO XCITING 250 Bedienungsanleitung
KYMCO
KYMCO PEOPLE 125 Bedienungsanleitung
KYMCO
KYMCO DINK 200 Bedienungsanleitung
KYMCO
KYMCO BET & WIN 50 Bedienungsanleitung
KYMCO
KYMCO Downtown 125i Bedienungsanleitung
KYMCO
KYMCO People S 250 Bedienungsanleitung
KYMCO
KYMCO downtown 300i Bedienungsanleitung
KYMCO
KYMCO People S 250 Bedienungsanleitung
KYMCO
KYMCO Agility 16+ 50 2022 Bedienungsanleitung
Beliebte Roller Handbücher anderer Marken
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung
Carrera
Carrera impel Bedienungsanleitung
Afikim
Afikim Superlight SL-3 Bedienungsanleitung
CareCo
CareCo ZOOM Bedienungsanleitung
Douglas
Douglas Vespa G.S. Bedienungsanleitung
Gazelle
Gazelle with BOSCH System Bedienungsanleitung