La Crosse Technology 308-146 Bedienungsanleitung

Model: 308-146/308146W www.lacrossetechnology.com/support 1

The Wireless Color Forecast Station features atomic time, weather forecast, indoor and outdoor

temperature/humidity as well as heat index and dew point, on a stylish, colorful, and easy to read display.

It has a USB charging port to charge your smartphone or other device. Transmission range of over 200

feet (60 meters) in open air, from transmitter to forecast station.

Wireless Color Forecast Station

Get Support: www.lacrossetechnology.com/308-146

INITIAL SETUP

Step 1: Insert the included 5-volt AC power adapter into forecast station and then into wall outlet.

Step 2: Insert 3 new “AA” batteries (not included) into the forecast station. Observe the correct polarity.

Step 3: Insert 2 new “AA” batteries (not included) into the outdoor transmitter. Observe the correct

polarity. The red LED will flash when transmitting.

Do Not Mix Old and New Batteries

Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries

RESTART:

If the outdoor temperature is not displayed after 3 minutes, unplug the AC adapter and remove

batteries from the forecast station & transmitter for 15 minutes.

Return to Step 1 above.

ATOMIC SIGNAL SEARCH:

The LCD backlight and USB charging port will momentarily turn off while the station searches for the

atomic signal. After the initial search, this station will only search for the atomic signal after midnight.

Model: 308-146/308-146W

Instruction Manual

Five

Forecast

Icons

Time,

Alarm,

Month,

Date +

Weekday

Outdoor Temperature ºF/ºC,

Humidity RH %

+ Channel Indicator

Indoor Temperature ºF/ºC

+ Humidity RH%

NOTE: This forecast station is sold

with one TX142TH sensor or one

TX14TH sensor. Either sensor

may be used interchangeably.

Model: 308-146/308146W www.lacrossetechnology.com/support 2

Table of Contents

Wireless Color Forecast Station 1

Initial Setup 1

Table of Contents 2

Features 3

Power the Forecast Station 3

A/C Power Adapter 3

Batteries 3

Install Batteries in the TX142TH Transmitter 4

Install Batteries in the TX14TH Transmitter 4

LCD Screen 4

Function Buttons 5

Program Menu 5

WWVB ON/OFF 5

Time Zone 6

Daylight Saving Time Indicator 6

12-hour or 24-hour Time Format 6

Set Time 6

Set Calendar 6

Fahrenheit/Celsius 6

Alarm Set 7

Deactivate Alarm 7

Snooze Alarm 7

USB Charge Port 7

Backlight 7

A/C Power Adapter 8

Batteries 8

Weather Forecast Icon 8

Min/Max Temperature Data 8

View Min/Max 8

Reset Min/Max 9

Heat Index 9

Dew Point Temperature 9

Low Battery Icon 9

Use Multiple Outdoor Transmitters 9

Channel Scroll 10

WWVB Radio-controlled Time 10

WWVB Reception Icon 10

Manual Signal Search 10

Care and Maintenance 11

Position the Outdoor Transmitter 11

Outdoor Temperature/Humidity Flashes 12

Position the Forecast Station 12

Specifications 12

Indoor 12

Outdoor 12

Humidity 12

Power Requirements 12

Battery Life 12

Dimensions 12

Warranty Information 13

FCC Statement 13

Model: 308-146/308146W www.lacrossetechnology.com/support 3

Features

•Atomic time and date (auto sets)

•12/24 hour time with snooze alarm and alarm icon

•Charge devices with USB charging port

•Calendar display: month, day, date

•Heat index and dew point

•Forecast: sunny, partly sunny, cloudy, rainy and stormy

•12 hour forecast based on changing barometric pressure

•IN / OUT temperature (°F / °C)

•IN / OUT humidity (%RH)

•MIN / MAX records (24-hour readings)

•Time zone selection: Atlantic Time (AST), Eastern Time (EST), Central Time (CST), Mountain Time

(MST), Pacific Time (PST), Alaskan Time (AKT) and Hawaiian Time (HAT)

•Light up the forecast station with a press of a button using battery power OR continuous light using

the AC adapter with ON / OFF option

•LCD light dimmer for nighttime use

•Low battery icon for forecast station and sensor

•Sits on desktop or tabletop

•3 "AA" Alkaline batteries (not included) OR optional 5.0V AC adapter (included)

Power the Forecast Station

The forecast station can be powered by the 5-volt a/c adapter or batteries.

A/C Power Adapter

Insert enclosed 5-volt a/c power adapter into a wall outlet, then into the forecast station.

Batteries

1. Remove battery cover: Slide tab to the right and pull out to remove battery cover.

2. Install three fresh AA batteries according to the polarity markings.

Do Not Mix Old and New Batteries

Do Not Mix Alkaline, Lithium, Standard, or Rechargeable Batteries

NOTE: If the forecast station does not display indoor temperature after 60 seconds, remove adapter and

batteries, and wait for at least 60 seconds before repeating the setup process.

Battery

Compartment

Model: 308-146/308146W www.lacrossetechnology.com/support 4

Install Batteries in the TX142TH Transmitter

NOTE: This forecast station will come with one TX142TH transmitter OR one TX14TH transmitter.

Both transmitters work interchangeably.

1. Slide the battery cover down, then lift off the front of the TX142TH transmitter.

Note: Be careful not to break the tabs on the battery cover.

2. Confirm the channel selector switch is on channel 1.

3. Insert two new AA batteries into the transmitter.

Observe the correct polarity (see marking inside battery compartment).

4. Keep transmitter 5-10 ft. from the forecast station during setup.

5. After 15 minutes, if the outdoor temperature shows on the forecast station,

move the outdoor transmitter outside to a shaded location within range of the forecast

station.

Install Batteries in the TX14TH Transmitter

1. Slide the battery cover down, then lift off the back of the TX14TH transmitter.

Note: Be careful not to break the tabs on the battery cover.

2. Confirm the channel selector switch is on channel 1.

3. Insert two new AA batteries into the transmitter.

4. Observe the correct polarity (see marking inside battery compartment).

5. Keep transmitter 5-10 ft. from the forecast station during setup.

6. After 15 minutes, if the outdoor temperature shows on the forecast station,

move the outdoor transmitter outside to a shaded location within range of the forecast station.

LCD Screen

The LCD screen is split into 5 sections displaying the information for time, calendar, weather forecast,

indoor data, and outdoor data.

Model: 308-146/308146W www.lacrossetechnology.com/support 5

Function Buttons

Button

Press and Release Functions

Hold 3-5 seconds

SET

Move through program menu Confirm

setting.

Enter program menu, set time,

date, etc.

ALARM

View Alarm

Activate/Deactivate Alarm

Alarm set

+/RCC

1 step forward (setup)

Search for WWVB signal

Fast advance (setup)

-/°C/°F

Select temperature in °C/° F

1 step backward (setup)

Fast backward (set)

MIN/MAX

1-time MAX values

2-times MIN values

Resets all MIN / MAX values

HEAT/DEW

1-time Heat Index

2-times Dew Point

Switch channels

(when using multiple transmitters)

Search for remote transmitter

LIGHT HI/LO

HOLD ON/OFF

Dim backlight for night time.

Turn continuous backlight

ON or OFF (a/c adapter)

LIGHT/SNOOZE (top)

Activates backlight when using only

batteries.

Trigger snooze alarm

Program Menu

The SET button will move through the items in the program menu. The +/RCC or -/°C/°F button will

change these values.

WWVB reception ON or OFF

Time Zone (Seven Time Zones)

Daylight Saving Indicator

12/24 hour time format

Manual time set (Hour, Minutes)

Calendar set (Year, Month, Date)

WWVB Reception ON/OFF

The WWVB time reception defaults to ON. To turn the WWVB reception OFF:

1. Hold the SET button for 5 seconds.

2. WWVB and ON will flash.

3. Press and release the +/RCC or -/°C/°F button to turn this OFF.

4. Confirm with the SET button and move to the Time Zone.

WWVB

Model: 308-146/308146W www.lacrossetechnology.com/support 6

Time Zone

This forecast station offers seven time zones listed in letter format (default is EST):

1. EST will flash.

2. Press and release the +/RCC or -/°C/°F button to select a different Time Zone.

3. Confirm with the SET button and move to Daylight Saving Indicator.

Daylight Saving Time Indicator

DST will default to the ON position as most of the country observes the DST change. This should be in

the ON position all year long. If you live in an area does not observe the DST change, switch this to the

OFF position.

1. DST and ON will flash.

2. Press and release the +/RCC or -/°C/°F button to turn DST to OFF.

3. Confirm with the SET button and move to 12/24 hour time format.

12-hour or 24-hour Time Format

The Time may be displayed in 12-hour or 24-hour format. Default is 12-hour time.

Note: When in 12-hour format AM or PM will show in front of the hour.

1. 12H will flash.

2. Press and release the +/RCC or -/°C/°F button to select 24-hour time.

3. Confirm with the SET button and move to Set Time.

Set Time

To set the time manually:

1. The hour digit will flash.

2. Press and release the +/RCC or -/°C/°F button to select the hour.

3. Press and release the SET button to set the minutes.

4. The minute’s digit will flash.

5. Press and release the +/RCC or -/°C/°F button to select the minutes.

6. Confirm with the SET button and move to Set Calendar.

Set Calendar

To set the calendar:

1. The year will flash.

2. Press and release the +/RCC or -/°C/°F button to set the year (between year 2010-2039).

3. Press the SET button again to confirm and to enter the month setting.

4. The month will flash.

5. Press and release the +/RCC or -/°C/°F button to set the month.

6. Press the SET button again to confirm and enter the date setting.

7. The date will flash.

8. Press and release the +/RCC or -/°C/°F button to set the date.

9. Confirm all calendar settings with the SET button to confirm and exit the program menu.

Note: The day of the week will set automatically once the year, month and date are set.

Fahrenheit/Celsius

1. Press and release the -/°C/°F button once to switch from Fahrenheit to Celsius.

DST

12H

2010

1M.1D

Model: 308-146/308146W www.lacrossetechnology.com/support 7

Alarm Set

Hold the ALARM button for 5 seconds to enter the alarm time set mode.

1. The alarm hour digit will flash.

2. Press and release the +/RCC or -/°C/°F button to select the hour.

3. Press and release the SET button to set the minutes. The minute digits

will flash.

4. Press and release the +/RCC or -/°C/°F button to select the minutes.

5. Confirm with the SET button and exit.

6. The alarm icon will show above the minutes indicating the alarm is active.

7. The alarm icon will flash when the alarm is sounding.

Deactivate Alarm

1. Press and release the ALARM button once to show Alarm Time.

2. Press and release the ALARM button to deactivate the Alarm. The alarm icon will disappear

indicating the alarm is no longer active.

Snooze

1. When the alarm sounds, press the SNOOZE/LIGHT button to trigger snooze alarm for 10 minutes.

The snooze icon Zz will flash when the snooze feature is active.

2. To stop alarm for one day, press ALARM button, while in snooze mode. The alarm icon will remain

solid.

Note: When the alarm sounds, it continues for 2 minutes and then shuts off completely.

USB Charge Port

Charge a smart phone, camera or other devices when the forecast station is

plugged into a power outlet with the included 5V AC adapter.

Note: This is a power-output charging port. It does not supply power to the

forecast station.

Connect your external device’s USB charging cable (not included) to the

USB charging port.

Charging times will vary.

USB Power Output: 1A maximum current. Charge 1A devices or devices

that are self-regulating.

Note: Some USB cables are for data transfer only and cannot be used for charging. Make sure that the

USB cable you use will charge your device. Most USB cables included with mobile devices will work for

charging.

ATOMIC SIGNAL SEARCH:

The LCD backlight and USB charging port will momentarily turn off while the station searches for the

atomic signal. After the initial search, this station will only search for the atomic signal after midnight.

Backlight

A/C Adapter

The backlight can show continuously when operating the forecast station with the 5-volt a/c adapter. If the

backlight is not on continuously, hold the HOLD ON/OFF button until the station beeps. The backlight

should show.

1. HIGH: The backlight defaults to HIGH (brightness) when the a/c adapter is in use.

2. LO: Press and release the LIGHT HI/LO button to dim the brightness of the backlight.

3. Press and release the LIGHT HI/LO button again to return to full strength (HIGH).

Note: When the Adapter is NOT in use, the High/Low backlight feature is not available.

Model: 308-146/308146W www.lacrossetechnology.com/support 8

1. OFF: Hold the HOLD ON/OFF button for 5 seconds, until the station beeps, to turn the backlight off to

sleep.

2. ON: Hold the HOLD ON/OFF button again until the station beeps, to turn the backlight on.

Note: When the backlight is off, press any button to activate the backlight for 8 seconds, and then it will

turn off again.

Battery Power

Press and release the SNOOZE/LIGHT button and the backlight will show for 8 seconds, when operating

on batteries only.

Weather Forecast Icons

The forecast station unit predicts weather condition for the next 12-hours based on the change of

atmospheric pressure. As weather conditions cannot be 100% correctly forecasted we cannot be

responsible for any loss caused by an incorrect forecast.

INTELLIGENT WEATHER FORECAST

This station learns. Please allow 3 to 4 weeks for barometric calibration. This will ensure an accurate

personal forecast for your location.

As the forecast station builds memory, it will compare the current average pressure to the past forty day

average pressure for increased accuracy. The longer the forecast station operates in one location the

more accurate the forecast icons will be.

The icons forecast the weather in terms of getting better or worse and not necessarily sunny or rainy as

each icon indicates. For example, if the current weather is cloudy and the rainy icon is displayed, it does

not mean that the product is faulty because it is not raining. It simply means that the air pressure has

dropped and the weather is expected to get worse but not necessarily rainy.

Common to weather forecasting, absolute accuracy cannot be guaranteed. The weather forecasting

feature is estimated to have an accuracy level of about 75% due to the varying areas the forecast station

has been designed for use. In areas that experience sudden changes in weather (for example from sunny

to rain), the forecast station will be more accurate compared to use in areas where the weather is

stagnant most of the time (for example mostly sunny).

MIN/MAX Temperature Data

This forecast station features daily minimum and maximum temperatures each day starting at midnight

(12:00 AM). The forecast station automatically resets the min/max temperatures at midnight (12:00 AM).

View Min/Max

MAX: From a normal display press and release the MIN/MAX button once to view maximum

temperature and humidity values for Indoor and Outdoor data. The word MAX will appear next to the

indoor and outdoor temperature.

MIN: From a normal display press and release the MIN/MAX button twice to view minimum temperature

and humidity values for Indoor or Outdoor data. The word MIN will appear next to the indoor and

outdoor temperature.

Model: 308-146/308146W www.lacrossetechnology.com/support 9

Reset Min/Max

Hold the MIN/MAX button for 5 seconds to manually reset each indoor and outdoor minimum and

maximum value. (The forecast station automatically resets the min/max temperatures at midnight: 12:00

AM).

Note: If you are using multiple transmitters connected to the forecast station, all channels will reset at the

same time.

Heat Index

Heat Index combines the effects of heat and humidity. It is the apparent temperature of how hot it feels to

a human being. When relative humidity increases, the air feels warmer than it actually is because your

body is less able to cool effectively by evaporation of perspiration.

View Heat Index: From a normal display press the HEAT/DEW button once and the Heat Index will show

instead of the ambient temperature. The words Heat Index will show near the indoor and outdoor

temperatures.

Note: Heat index will be the same number as the temperature until the temperature is above 80 degrees

°F (26.7°C).

Dew Point Temperature

Dew point is the saturation point of the air, or the temperature to which the air has to be cooled in order to

create condensation. The higher the dew points, the higher the moisture content of the air at a given

temperature. Dew Point Temperature is the absolute measure of the moisture in the air at a given

temperature. Relative humidity is the relative measure of moisture in the air at a certain temperature.

View Dew Point: From a normal display press the HEAT/DEW button twice and the Dew Point

temperature will show instead of the ambient temperature. The words Dew Point will show near the

indoor and outdoor temperatures.

Note: Dew Point is lower than the actual temperature.

Low Battery Icon

When this icon appears in the indoor (IN) data reading section, replace the batteries in the forecast

station.

When this icon appears in the outdoor (OUT) data readings section, replace the batteries in the

outdoor transmitter.

Use Multiple Outdoor Transmitters

The forecast station will accommodate up to three remote outdoor transmitters (TX142TH or TX14TH).

The channel selection button allows you to easily see the temperature in various locations: outdoors,

baby’s room, greenhouse, basement, etc.

Model: 308-146/308146W www.lacrossetechnology.com/support 10

To connect multiple remote transmitters to the forecast station:

1. Remove the battery cover from all the transmitters (Leave battery covers off until all

transmitters are received by the forecast station).

2. Set the first outdoor transmitter to Channel 1 and insert 2-AA batteries.

3. Set the second outdoor transmitter to Channel 2 and insert 2-AA batteries.

4. Set the third outdoor transmitter to Channel 3 and insert 2-AA batteries.

5. Press and hold CH button on the forecast station until a beep sounds. The forecast

station will search for all outdoor transmitters.

6. Press the TX button on each outdoor transmitter to transmit RF signal.

7. When RF connection is established, the respective temperature & humidity for each of

the selected channels numbers will appear on the main unit.

8. Allow the transmitters and the forecast station to stay 5-10 feet apart for 15 minutes to

establish a solid connection.

9. Install the battery covers on each sensor.

10. After 15 minutes place the remote transmitters in appropriate locations (see “position the

outdoor transmitter”).

11. Press and release the CH button to view channel 1, 2 or 3 on the forecast station when multiple

transmitters are used.

Note: You cannot change channels if only one transmitter is connected.

Channel Scroll

1. Press and release the CH button until the word AUTO appears in the outdoor data area. The forecast

station will automatically rotate through the channels for all connected transmitters.

2. Press and release the CH button to lock the forecast station into one channel. Then view channels

individually with a press of the CH button.

WWVB Radio-controlled Time

The NIST radio station, WWVB, is located in Ft. Collins, and transmits the exact time signal continuously

throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the

internal antenna in the forecast station. However, due to the nature of the Earth’s Ionosphere, reception is

very limited during daylight hours. The forecast station will search for a signal every night when reception

is best. The WWVB radio station derives its signal from the NIST Atomic Clock in Boulder, Colorado. A

team of atomic physicists continually measures every second of every day to an accuracy of ten billionths

of a second a day. These physicists have created an international standard, measuring a second as

9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. This atomic clock regulates the WWVB

transmitter.

WWVB Reception Icon

The WWVB time reception icon with full signal strength will appear on screen in front of the

date when the reception of time is successful.

The tower icon will show solid when the forecast station has received the WWVB signal.

No tower icon is shown. The forecast station was unable to receive a signal at this time.

Reposition the forecast station for better signal reception or try again at bedtime.

The forecast station will start searching at UTC: 07:00 and if no reception on the first attempt they will

try again at 08:00, 09:00 and 10:00. Each attempt will be at least 2 minutes and the most will be 10

minutes.

If there is no signal or too much interference the receiver will only be on for 2 minutes.

If the signal is good it may catch a signal in ABOUT 2-3 minutes.

If the signal is marginal it will try to catch a signal for up to 10 minutes.

IMPORTANT: When operating on a/c power, the backlight and USB charge port will turn off while the

forecast station searches for the WWVB signal, to avoid interference. Both features will return after

the 2-10 minute search which occurs during the late night or early morning hours.

Note: In case the forecast station is not able to detect the WWVB-signal (disturbances, transmitting

distance, etc.); the time may be manually set.

Andere Handbücher für 308-146

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-9125U-IT-CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology WEATHER DIRECT WD-3103U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9014 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-146W Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009BK-IT Abmessungen

La Crosse Technology

La Crosse Technology WS-2010 Leitfaden

La Crosse Technology

La Crosse Technology WS-2811U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology C85845V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7211U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7044UA Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-2414FR Abmessungen

La Crosse Technology

La Crosse Technology WS-9037U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1612 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9066U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7095U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 512-807 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V15 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425BV3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6821A Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8610U Bedienungsanleitung

La Crosse Technology

La Crosse Technology T83653v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 328-2314 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology C84428 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6868 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung