La Crosse Technology WS-9014 Bedienungsanleitung

868 MHZ TEMPERATURE STATION

INSTRUCTIONS MANUAL

INTRODUCTION:

Congratulations on purchasing this innovative 868MHz Temperature Station which displays the time with up

to the minute indoor and up to three outdoor temperature readings. To en oy the full benefits of this

innovative product, please read this operating manual.

Temperature Station:

Temperature Transmitter:

• Remote transmission of outdoor temperature to weather station by 868

MHz signal

• Wall mounting case

• Mounting at a sheltered place. Avoid direct rain and sunshine

SET CHANNEL key

RESET + MIN MAX

key

Hanging hole

Detachable stand

FEATURES:

• LCD clock in 12 or 24 hour time display

• Indoor and outdoor temperature reading in degree Celsius (°C) or degree Fahrenheit (°F)

• Can receive up to three Outdoor transmitters

• Indoor and outdoor temperature with Minimum and Maximum records

• Wireless transmission at 868 MHz

• Signal reception intervals at 4 seconds

• Table standing or wall mountable (detachable table stand)

SETTING UP:

WHEN ONE TRANSMITTER IS USED

1. First, insert the batteries in the transmitter (see “How to install and replace batteries in the

Temperature Transmitter” below).

2. Within 2 minutes of powering up the transmitter, insert the batteries in the Temperature

Station (see “How to install and replace batteries in the Temperature Station” below).

Once the batteries are in place, all segments of the LCD will light up briefly. Following the

indoor temperature and the time as 0:00 will be displayed. If these information are not

displayed on the LCD after 60 seconds, remove the batteries and wait for at least 60 seconds

before reinserting them. Once the indoor data is displayed user may proceed to the next step.

3. After the batteries are inserted, the Temperature Station will start receiving data signal from

the transmitter. The outdoor temperature data should then be displayed on the Temperature

Station. If this does not happen after 2 minutes, the batteries will need to be removed from

both units and reset from step 1.

4. In order to ensure sufficient 868 MHz transmission however, the distance between the Weather

Station and the transmitter should not be more than 100 meters (see notes on “Positioning” and

“868 MHz Reception”).

Note:

In the event of changing batteries of the units, ensure the batteries do not spring free from the contacts.

Always wait at least 1 minute after removing the batteries before reinserting, otherwise start up and

transmission problems may occur.

WHEN MORE THAN ONE TRANSMITTER IS USED

1. User shall remove all the batteries from the Weather Station and transmitters, and wait 60 seconds.

2. Insert the batteries in the first transmitter.

3. Within 2 minutes of powering up the first transmitter, insert the batteries in the Temperature Station.

Once the batteries are in place, all segments of the LCD will light up briefly. Following the indoor

temperature and the time as 0:00 will be displayed. If these information are not displayed on the LCD

after 60 seconds, remove the batteries from both units and wait for at least 60 seconds before

reinserting them.

4. The outdoor temperature data from the first transmitter (channel 1) should then be displayed on the

Temperature Station. Also, the signal reception icon will be displayed. If this does not happen after 2

minutes, the batteries will need to be removed from both units and reset from step 1.

5. Insert the batteries in the second transmitter as soon as the outdoor temperature readings from the

first transmitter are displayed on the Temperature Station.

Note : User shall insert the batteries into the second transmitter within 45 seconds after the

Temperature Station displays the information of the first transmitter.

6. The outdoor temperature from the second transmitter and the "channel 2" icon should then be

displayed on the Temperature Station. If this does not happen after 2 minutes, the batteries will need

to be removed from all the units and reset from step 1.

7. Insert the batteries in the third transmitter as soon as the "channel 2" icon and outdoor data are

displayed on the Temperature Station. Then within 2 minutes, the channel 3 outdoor data from the

third transmitter will be displayed and the channel icon will shift back to "1" once the third transmitter

is successfully received. If this is not happen, user shall restart the setting up from step 1.

Note : User shall insert the batteries into the third transmitter within 45 seconds after the

Temperature Station displays the information of the first transmitter. Or immediately after reception of

the second transmitter is finished.

8. In order to ensure sufficient 868 MHz transmission however, the distance between the Weather

Station and the transmitter should not be more than 100 meters (see notes on “Positioning” and

“868 MHz Reception”).

IMPORTANT:

Transmission problems will arise if the setting for additional sensors is not followed as described above.

Should transmission problems occur, it is necessary to remove the batteries from all units and start again

the set-up from step 1.

HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION

The Temperature Station uses 2 x AA, IEC LR6, 1.5V batteries. If the batteries need

to be replaced, the low battery symbol will appear on the LCD.

To install and replace the batteries, please follow the steps below:

1. Insert finger or other solid ob ect in the space at the bottom center of the

battery compartment and lift up to remove the cover.

2. Insert batteries observing the correct polarity (see marking).

3. Replace compartment cover.

HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER

The Temperature Transmitter uses 2 x AA, IECLR6, 1.5V batteries. To install and

replace the batteries, please follow the steps below:

1. Slide the battery cover downwards and remove.

2. Insert the batteries, observing the correct polarity (see marking).

3. Replace the battery cover.

Note:

In the event of changing batteries in any of the units, all units need to be reset by

following the setting up procedures. This is because a random security code is assigned

by the transmitter at start-up and this code must be received and stored by the Temperature Station in the

first three minutes of power being supplied to it.

BATTERY CHANGE:

It is recommended to replace the batteries in all units on an annual basis to ensure optimum accuracy of

these units.

Please participate in the preservation of the environment. Return used batteries to an

authorized depot.

LCD SCREEN

The Temperature Station’s LCD is comprised of three lines and once the batteries are inserted, all the

segments will light up momentarily before displaying:

Time

Indoor Temperature

in ºC or °F

Outdoor

Temperature

in ºC or °F Outdoor transmission signal*

Transmitter identification number

1. Time “_;_ _”

2. Indoor and outdoor temperature in degree Celsius (°C) or Fahrenheit (°F)

* When the signal is successfully received by the Weather Station, the outdoor transmission icon will be

switched on. (If not successful, the icon will not be shown on LCD). The user can then easily see whether

the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of the icon

shows that a reception is currently taking place.

12 OR 24 HOUR SETTING:

After the batteries are inserted, set the time display as follow:

1. Press and hold the “SET CHANNEL” key about 3 seconds to enter the set mode

2. Either a “: 12h” or “: 24h” will appear on the LCD. If “: 12h” is displayed then the current time display

is set to 12-hour time. If “: 24h” is displayed then the current time is set to 24-hour time.

To alternate between the two times display mode, simply press the “RESET + MIN MAX” key.

4. When the desired time display is selected, press the “SET CHANNEL” key once more to enter the

Time setting mode.

Note:

When the time display is set as 12-hour mode, the temperature unit will be set to °

°°

°F; when the time

mode is in 24-hour format, the temperature unit will be set to °

°°

°C.

TIME SETTING:

Following from the 12 or 24 hour setting mode.

1. The Hour digit in the time section starts flashing

2. Using the “RESET + MIN MAX” key, enter the hours of the current time and then followed by

pressing the “SET CHANNEL” key to move into the minutes mode

3. Again, using the “RESET + MIN MAX” key, enter the minutes of the current time (by holding the key

down, the digits are incremented in steps of five) and then finally followed by pressing the

“SET CHANNEL” key to exit the setting mode. Your Temperature Station is now fully operational.

USING THE TEMPERATURE STATION:

INDOOR TEMPERATURE:

The indoor temperature is displayed on the second line of the LCD under the time. The Temperature

Station’s built in sensor automatically measures the temperature once the batteries are inserted.

MINIMUM AND MAXIMUM INDOOR TEMPERATURE RECORDINGS:

By pressing the “RESET + MIN MAX” key the current indoor temperature will alternate between the

minimum, maximum and current temperature recordings (also changes for outdoor temperature). Once a

new indoor temperature high or low is reached, it will automatically set into the Temperature Station’s

memory.

OUTDOOR TEMPERATURE READING:

The outdoor temperature reading is on the bottom line of the LCD under the indoor temperature. The

Temperature Station receives the outdoor temperature via 868 MHz frequency when the batteries are

inserted into the transmitter within the 2 minutes of the setting up time (See Setting up above).

Note: Should the outdoor temperature not be received within 2 minutes after inserting the batteries into

a transmitter, then see “Checking 868 MHz reception” below.

MINIMUM AND MAXIMUM OUTDOOR TEMPERATURE READING:

By pressing the “RESET + MIN MAX” key the current indoor and outdoor temperature will alternate between

the minimum, maximum and current temperature recordings. Once a new outdoor temperature high or is low

reached, it will automatically be set into the Temperature Station’s memory.

RESETTING THE MINIMUM AND MAXIMUM TEMPERATURE RECORDING:

By pressing and holding down the “RESET + MIN MAX” key for about 3 seconds, both the indoor and

outdoor minimum and maximum temperature recordings will be reset to the current indoor and outdoor

temperatures. Only the outdoor temperature display on the LCD will be reset. To reset an outdoor

temperature moves to the desired transmitter no.

OUTDOOR TEMPERATURE 1, 2, AND 3

If the more than one transmitter is being used, to alternate between the temperature readings of transmitter

1, 2, and 3, simply press the “SET CHANNEL” key. If the reading is from transmitter 1, then the

identification numbers 1 will be displayed in the outdoor temperature section of the LCD. The same will

apply to the next transmitter and so on. However, if only one transmitter is used, no identification number

will be displayed on the LCD.

CHECKING FOR 868 MHz RECEPTION:

In normal surroundings (for example away from interfering sources such as TV sets), the outdoor

temperature can usually be easily received within 2 minutes. If the outdoor temperature is not displayed on

the LCD after 2 minutes, then check the following:

1. The distance of the units should be at least 1.5 - 2.0 meters away from interfering sources such as

computer monitors or TV sets.

2. Avoid placing the units onto or in the immediate proximity of metal doors, window frames or

structures.

3. Using other electrical products such as headphones and speakers that operate on the same signal

(868 MHz) can prevent the transmission pick up.

4. Neighbours using electrical products operating on the 868 MHz signal can also cause interference.

In most severe cases, the reception is only possible once all other electrical products using the 868

MHz are switched off.

5. Within thick concrete rooms such as basements and tower blocks, the 868 MHz signal can be

weakened (avoid placing near metal frames and structures).

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1409 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology V15 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1412 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425BV3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V22-WRTHV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7034U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1711BLV2 Abmessungen

La Crosse Technology

La Crosse Technology WS-2315CH Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415FCT Abmessungen

La Crosse Technology

La Crosse Technology 308-1451v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX141TH-B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7014CH-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology S98642 Betriebsanleitung

La Crosse Technology

La Crosse Technology WS6212 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2811U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C75747-AU Bedienungsanleitung

La Crosse Technology

La Crosse Technology Family Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9121U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology V22-WRTH Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-450B Bedienungsanleitung

La Crosse Technology

La Crosse Technology T85647v2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-9049 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung