La Crosse Technology TX2000 Discovery Bedienungsanleitung

CONTENTS

Topic Page

Inventory of Contents

About WWVB

Quick Set-Up Guide

Detailed Set-Up Guide

Battery installation

Program Mode

Program Sequence

Function Keys

Setting the LCD Contrast

Time Zone Setting

Daylight Saving Time Setting

Radio-Controlled Time Setting

12/24 Hour Time Setting

Time Setting (WWVB & Manual)

Setting the Year, Day and Month

Setting the Snooze

Setting the Temperature Format

Features

Indoor Temperature

Outdoor Temperature

Minimum & Maximum Records (Indoor, Outdoor, & Resetting)

Alarm (Setting, Snoozing & Stopping)

Viewing date, weekday or alarm time

Additional Remote Control Sending Units (Set-Up, Viewing, &

Operation)

Mounting

Troubleshooting

Maintenance & Care

Specifications

Warranty Information

INVENTORY OF CONTENTS

1. The thermo station (Figure 1).

2. One TX6U remote temperature sensor with mounting bracket (Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction manual and warranty card.

Additional Equipment (not included)

1. Two, fresh AA 1.5V batteries.

2. Two, fresh AA 1.5V batteries.

3. One, Philips screwdriver.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency Division)

WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time and date

signal continuously throughout the United States at 60 kHz. The signal can be received up to

2,000 miles away through the internal antenna in the Weather Station. However, due to the

nature of the Earth’s Ionosphere, reception is very limited during daylight hours. The weather

station will search for a signal every night when reception is best. The WWVB radio station

derives its signal from the NIST Atomic clock in Boulder, Colorado. A team of atomic

physicists is continually measuring every second, of every day, to an accuracy of ten

billionths of a second per day. These physicists have created an international standard,

measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For

more information on the atomic clock and WWVB please see the NIST website at

http://www.boulder.nist.gov/timefreq/stations/wwvb.htm.

Figure 1 Figure 2

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor thermo station and remote temperature sensor 3 to 5

feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into

the thermo station.

(All outdoor remotes must be started before the indoor station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the indoor thermo station and remote temperature sensor will start to talk

to each other and the display will show the indoor temperature and an outdoor

temperature. If the indoor thermo station does not display all information after the

15 minutes please retry the set up as stated above. After all information has been

displayed for 15 minutes you can place your sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote

temperature sensor has a range of 330 feet. Any walls that the signal will have to

pass through will reduce distance. An outdoor wall or window can have up to 30

feet of resistance and an interior wall can have up to 20 feet of resistance. Your

distance plus resistance should not exceed 330 ft. in a straight line.

Note: Fog and mist will not harm your remote temperature sensor but direct rain

must be avoided.

Note: The remote temperature sensor transmits a signal every minute. After the

batteries have been installed, the indoor thermo station will search for the signal for

a duration of 15 minutes. If there is no temperature reading in the OUTDOOR LCD

after 15 minutes, make sure the units are within range of each other, or repeat the

battery installation procedure. If a button is pressed before the indoor weather

station receives the temperature signal, you will need to follow the battery

installation procedure again.

To complete the set up of your wireless temperature station after the 15 minutes have

passed please follow the steps that follow in the Detailed Set-Up Guide.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The

bracket snaps on and off easily.

2. Remove the battery cover, by sliding the

cover down.

3. Observing the correct polarity install 2 AA

batteries. The batteries will fit tightly (to

avoid start-up problems make sure they do

not spring free).

4. Replace the battery cover by sliding upwards. Be sure battery

cover is on securely.

B. INDOOR THERMO STATION

1. Remove the battery cover. To do

this, insert a solid object in the space

provided at the lower-central

position of the battery cover, then

push up and pull out on the battery

cover.

2. Observe the correct polarity, and

install 2 AA batteries.

3. Replace the battery cover.

Note: Immediately after the batteries have been installed, the

LCD (Liquid Crystal Display) will flash, and a tone will sound.

Within a few seconds the indoor temperature, indoor relative

humidity, will be displayed. If not, remove batteries for 10

seconds and reinstall. If the outdoor temperature is not displayed

within four minutes, remove batteries from both units, wait 10

seconds, and reinstall making sure to install batteries into the

remote temperature sensor first. The time will show -:-- and start

searching for the signal. If it successfully receives the time signal

(usually at night), it will display the correct time (default time-

Battery

com

artment

Battery

Cover

zone is Eastern). You will need to adjust the time zone to match

your local time.

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or the CH button is

pressed during the programming mode, the unit will confirm/set the last

information entered—the display will stop flashing and return to normal

time-date readings. If you don’t leave the program mode during the

programming of sections III through XI, you can advance to step 4 of the

next program setting. If you do leave the program setting (or want to

program a specific setting) follow each instructional step to program that

setting.

I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS

The programming sequence and default (factory) settings are as

follows:

LCD Contrast 5

Time Zone -5 (Eastern)

Daylight Saving Time 1 (on)

Radio-controlled time reception ON

12/24-hour time 12

Time 12:00

Year 2003

Day and Month 1.1.

Snooze 10

Temperature Format °F

II. FUNCTION KEYS

The Secondary Buttons are located directly below the Primary Buttons, and

behind the shield on the face of the unit. To access the Secondary Buttons:

place a solid object in the slot (above the shield) and gently pull out and

down.

III. SETTING THE LCD CONTRAST

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

Note: There are 8 LCD contrast levels to choose from—“Lcd 0” is

the lightest, and “Lcd 7” is the darkest.

3. Press and release the IN button to select the level you desire.

4. Press and release the SET button to confirm and advance to

the Time Zone setting.

Primary Buttons

Secondary Buttons

IV. TIME ZONE SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting

will flash.

3. Press and release the SET button again.

4. The time zone will flash in the date LCD.

5. Press and release the IN button to select your time zone.

Note: When a time zone for the U.S. is selected the corresponding

abbreviation will appear above the time (please see the table). It is

possible to select any time zone from –12 GMT to +12 GMT (for

example to see the time in another country)

TIME ZONES

GMT 0

Atlantic -4

EST; Eastern -5

CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

6. Press and release the SET button to confirm and advance to

the Daylight Saving Time setting.

V. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button twice.

4. “DST” will appear in the date LCD and either “1” or “0” will

flash.

5. Press and release the IN button to select DST on or off.

“DST 0” indicates that the feature is off and the WWVB will not

change times automatically. “DST 1” indicates that the feature is

on and the WWVB will change times automatically.

Note: Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST 0.”

6. Press and release the SET button to confirm and advance to

the radio-controlled time on/off setting.

VI. RADIO-CONTROLLED TIME ON/OFF SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button three times.

4. “RCC” will appear in the date LCD and “ON” or “OFF” will

flash in the time LCD.

5. Press and release the IN button to select radio-controlled time

on or off.

6. Press and release the SET button to confirm and advance to

the 12/24-hour time setting.

VII. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button four times.

4. “12h” or “24h” will flash in the time LCD.

5. Press and release the IN button to select 12 or 24-hour time

format.

Note: When in the 12-hour format “P.M.” will appear to the left

of the hour in the time LCD between the hours of noon and

midnight.

6. Press and release the SET button to confirm and advance to

the time setting.

VIII. TIME SETTING

There are two methods by which the time and date can be set:

A) Automatically via WWVB reception, or

B) Manually.

A. WWVB (Remote Control Time)

This method requires you to do nothing, except wait for the signal to be

received, and to select a time zone. Reception usually takes

approximately 10 minutes during optimal conditions. The best

condition for reception is at night, between midnight and 6:00 am—

when there is less atmospheric interference. To keep your time as

accurate as possible, the thermo station conducts a WWVB search

every night between these hours, and overrides any manually set time.

The WWVB tower icon (appearing in the TIME LCD) will flash when

a signal-search is in progress and a signal is being received, and will

remain steady when the signal has been received. If the WWVB time

has not been received after 10 minutes of battery installation, you may

manually set the time or leave the time function alone (reception will

occur regardless).

B. MANUAL TIME SETTING

Note: When in the 12-hour format “P.M.” will appear to the left of the

hour in the time LCD between the hours of noon and midnight.

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button five times.

4. The time will flash in the time LCD.

5. Press and release the IN button to advance the hours.

6. Press and release the OUT button to advance the minutes.

7. Press and release the SET button to confirm and advance to the

year setting.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology V50 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425BV3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7220U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417v3 Abmessungen

La Crosse Technology

La Crosse Technology WS-9023U-IT Abmessungen

La Crosse Technology

La Crosse Technology WS-1516-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology V23 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9520U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1416v2 Installationsanleitung

La Crosse Technology

La Crosse Technology S81120v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-450B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS 9711 IT+ Installationsanleitung

La Crosse Technology

La Crosse Technology WS-9077U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8610U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7014CH-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9250U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21-WTHv2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9046U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1516-IT Installationsanleitung

La Crosse Technology

La Crosse Technology Tomorrow's Weather Today WS-7394U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7097U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 328-10618 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035U-IT Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung