La Crosse Technology Tomorrow's Weather Today WS-7394U-IT Bedienungsanleitung

WS-7394U-IT

Wireless 915 MHz

WirelessWeather Station

Instruction Manual

FCC ID: OMOTX29U (transmitter)

RF Exposure mobile:

The internal / external antennas used for this mobile transmitter must

provide a separation distance of at least 20 cm (8 inches) from all

persons and must not be co-located or operating in conjunction with

any other antenna or transmitter.”

Statement according to FCC part 15.19:

This device complies with Part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Statement according to FCC part 15.21:

Modifications not expressly approved by this company could void the

user’s authority to operate the equipment.

Statement according to FCC part 15.105:

NOTE:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help

Contents

Language Page

English 2

French 28

Spanish 54

GB P.2 GB

P.3

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

About WWVB 3

Quick Set Up Guide 4

Detailed Set Up Guide

Battery Installation 5

Start Up Sequence 7

Explanation of LCD Information 8

Function Key Layout 9

Program Mode

Overview of Programming Sequence 9

LCD Contrast Setting 9

Time Zone Setting 10

DST ON/OFF Setting 10

Radio-controlled Time ON/OFF Setting 11

12/24-hour Time Mode Setting 11

Setting the Time/Date Manually 12

Temperature Measuring Units (˚F/˚C) 14

Air Pressure Measuring Units (inHg/hPa) 14

Relative Pressure Setting 14

Forecast Sensitivity Setting 15

Features and Operation

Minimum/Maximum Temperature/Humidity 16

Multiple Remote Temperature/Humidity Sensors 17

Comfort Icon 18

Weather Forecast and Pressure Trend Indicators 18

Weather Icons 19

Weather Tendency Arrows 19

Barometric Air Pressure Reading 19

Air Pressure History Bar Chart 20

Mounting 20

Maintenance and Care 23

Troubleshooting Guide 23

Specifications 24

Warranty Information 25

This product offers:

INSTANTTRANSMISSION

is the

state-of-the-art new wireless

transmission technology, exclu-

sively designed and developed by

LA CROSSETECHNOLOGY.

IN-

STANT TRANSMISSION

offers

you can an immediate update (every 4 seconds!) of all your outdoor

data measured from the transmitters:follow your climatic variations

in real-time!

INVENTORY OF CONTENTS

1.WS-7394U-IT- Wireless Weather Station (Figure 1)

2.TX29U-IT-remote temperature sensor (figure 2)

3. Instruction manual and warranty card

ADDITIONAL EQUIPMENT (not included)

1. Four fresh AA 1.5V alkaline batteries.

2. One wall-mounting screw (optional)

ABOUTWWVB (radio-controlled time)

The NIST (National Institute of Standards and Technology-Time and

Frequency Division) radio station, WWVB, is located in Ft. Collins,

Colorado and transmits the exact time signal continuously throughout

the United States at 60 kHz. The signal can be received up to 2,000

miles away through the internal antenna in the Wireless Weather

Station. However, due to the nature of the Earth’s Ionosphere, recep-

Figure 1 Figure 2

Mounting

Bracket TX29U-IT remote

temperature sensor

Battery Cover

SIZE AA LR6

GB P.4 GB

P.5

tion is very limited during daylight hours. The Wireless Weather Sta-

tion will search for a signal every night when reception is best. The

WWVB radio station derives its signal from the NIST Atomic clock in

Boulder, Colorado. A team of atomic physicists continually measure

every second of every day to an accuracy of ten billionths of a second

a day. These physicists have created an international standard, mea-

suring a second as 9,192,631,770 vibrations of a Cesium 133 atom in

a vacuum. For more information about WWVB please see the NIST

website at http://www.boulder.nist.gov/timefreq/stations/wwvb.htm

QUICK SET-UP GUIDE

Hint:

Use good quality Alkaline Batteries and avoid rechargeable

batteries.

1. Have the Wireless Weather Station and remote temperature sen-

sor 3 to 5 feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then

Wireless Weather Station.

(All remote temperature sensors must be started before the

WirelessWeather Station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time theWireless Weather Station and remote temperature sen-

sor will start to talk to each other and the display will show both the

indoor temperature and humidity, and an outdoor temperature. If the

Wireless Weather Station does not display both temperatures after

the 15 minutes please retry the set up as stated above. After both

indoor and outdoor temperatures are displayed for 15 minutes you can

place your remote temperature sensor outdoor and set your time.

The remote temperature sensor should be placed in a dry, shaded

area. The temperature sensor has a range of 330 feet. Keep in mind

that the 330 feet is in open air with no obstructions and that radio

waves DO NOT curve around objects. Actual transmission range will

vary depending on what is in the path of the signal. Each obstruction

(roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal

range in half.

Example: AWirelessWeather Station with a 330 feet range is mounted

on an interior wall, so that the signal has to pass through one interior

wall, one exterior wall, and across the 10 feet width of the room be-

tween the 2 walls. The first wall will reduce the range to 165 feet, and

the second wall will reduce the range to 87 feet. Factoring in the 10

foot room, this leaves a maximum of 77 feet of remaining signal range.

This allowance is typically enough for a frame wall with non-metallic

siding;however certain materials can reduce range even further. Metal

siding, stucco, and some types of glass can reduce signal range by as

much as 3/4 or more, compared to the 1/2 reduction typical of most

obstructions. It is possible to receive a signal through these materials,

however maximum range will be much less due to their tendency to

absorb or reflect a much larger portion of the sensor’s signal.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION (When one temperature sensor is

being used)

1. First, insert the batteries to the temperature sensor (see “A. Re-

moteTemperature Sensor” below).

2. Within 2 minutes of powering up the sensor, insert the batteries to

the Weather Station (see “B. Wireless Weather Station” below).

Once the batteries are in place, all segments of the LCD will light

up briefly. Following the indoor temperature and humidity, and the

time as 12:00 will be displayed. If they are not shown in LCD after

60 seconds, remove the batteries and wait for at least 60 seconds

before reinserting them. Once the indoor data is displayed user

may proceed to the next step.

3. After the batteries are inserted, the Weather Station will start re-

ceiving data signal from the sensor.The outdoor temperature should

then be displayed on the Weather Station. If this does not happen

after 2 minutes, the batteries will need to be removed from both

units and reset from step 1 and the signal reception icon is no longer

shown.

A. RemoteTemperature Sensor

1. Remove the mounting bracket. The bracket snaps on and off easily.

2. Remove the battery cover, by sliding the cover down.

Battery Compartment

GB P.6 GB

P.7

3. Observing the correct polarity install 2 AA batteries. The batteries

will fit tightly (to avoid start-up problems make sure they do not

spring free).

4. Replace the battery cover by sliding upwards.Be sure battery cover

is on securely.

B. WirelessWeather Station

1. Remove the battery cover (the cover has white writing on it).

2. Observe the correct polarity, and install two Alkaline AA batteries.

3. Do not press any buttons for at least ten minutes. If a button is

pressed before the indoor weather station has received informa-

tion from the TX29U-IT sensor, no data will be received from that

sensor until reset.

4. Replace the battery cover.

*When the signal is successfully received by the Weather Station,

the icon will be switched on.(If not successful, the icon will not be

shown in LCD) So the user can easily see whether the last recep-

tion was successful (icon on) or not (icon off). On the other hand,

the short blinking of the icon shows that a reception is being done

now.

•If the signal reception is not successful on the first frequency

(915MHz) for 45 seconds, the frequency is changed to 920MHz

and the learning is tried another 45 seconds. If still not successful

the reception is tried for 45 seconds on 910MHz.This will also be

done for re-synchronization.

II. Start Up Sequence

A. Initial Start

1. Immediately after the batteries have been installed the LCD will

completely light up for a brief moment.

2. All information will then appear in normal mode, with “12:00”as the

default time and “SA.1” as the default date (2006 as the year).

3. The indoor temperature and humidity, and barometric air pressure

(as 29.92 inHg relative RH) will also be displayed.

4. There is a “satellite”icon that appears in the bottom portion of the

LCD, to the left of the outdoor temperature- this icon informs the

user that the indoor weather station is looking for signals from the

remote temperature sensor. Within five minutes the remote tem-

perature should be displayed-if not, remove batteries from all units

and repeat battery installation, the remote temperature sensor first,

then the indoor weather station.

B. WWVB Reception

1. Once the batteries are installed in the WirelessWeather Station it

will automatically search for theWWVB signal.If it receives a good

signal (which is unlikely during daylight hours in most locations),

the WWVB reception indicator (looks like a tower icon) will flash.

The Wireless Weather Station requires five full minutes of good

reception to successfully capture the signal and set to the correct

hour, minute, second, month, day and year.If the signal reception

is not successful within ten minutes, the signal search will be

cancelled. Next reception will take place the next day.

2. The signal is sent from Ft. Collins, Colorado only and is similar to

an AM radio signal. Atmospheric interferences such as storms,

sunspots, and even sunlight will cause the signal to not travel as

far.

3. To maximize reception, place the Wireless Weather Station n in a

window facing Colorado, at least six feet from any electrical source

(computers, televisions, refrigerators, etc.). Do not move the in-

door weather station while it is searching for the signal.

4. The time and date can be manually set.Once the signal is captured,

it will override any time and date set to the time zone selected.

5. Once the time and date are set, the Wireless Weather Station will

conduct a search every night at midnight and correct to the accu-

rate time and date (Daylight Saving Time is automatic).If the signal

has been received in the past 24 hours, the reception indicator will

be displayed. After a successful reception, no more reception at-

tempt would be made until the following day.

Sensor signal

reception icon*

Battery cover

GB P.8 GB

P.9

III. Explanation of LCD Information

A. The below picture highlights the LCD features.

B. There are many different modes the indoor weather station can be

set to. The LCD shown is the normal operating mode, and your

actual data shown will be different based on your local settings and

conditions.

Radio-controlled

time

WWVB Reception

Indicator

Date Display

Comfort Icon

Indoor Temperature

Humidity Display

Air Pressure Trend

Indicator

Forecast Icon

Barometric Air

Pressure

12-hour Air

Pressure History

Outdoor

Temperature Display Remote Sensor

Number (Up to 3

Total)

IV.Function Key Layout

A. The below picture shows the four function keys used in program-

ming and operation of your indoor weather station

V. Program Mode

The program mode is laid out in a manner that allows you to program

each function separately, or you can follow the instructions entirely to

program the Wireless Weather Station. Complete programming is

usually done for the initial set-up, and will require you to skip step 1,2

and 3 of each programming section. The programming mode can be

exited at any time by either pressing the“CH” button, or waiting for the

15-second time-out to take effect.

A. Overview of programming mode sequence

B. LCD Contrast Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “OUT/+” button to select the desired LCD

contrast setting.

4. Press and release the “SET” button to confirm the LCD contrast

setting and continue to theTime Zone setting.

1. LCD Contrast 2. Time Zone 3. DST ON/OFF

4. Radio-controlled 5. 12/24-hour 6. Hour

Time ON/OFF time mode

7. Minute 8. Year 9. Month

10. Date 11. ˚F/˚C 12. inHg/hPa

13. Relative pressure setting 14. Forecast sensitivity

GB GB

P.11P.10

C. Time Zone Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button once more to advance to the

Time Zone setting.

4. A number will flash to the left of the letter“h” at the top of the display

just below the time display.

5. Press and release the “OUT+” button to select the desired time

zone.

6. Press and release the “SET”button to confirm the Time Zone set-

ting and continue to the DST ON/OFF setting.

D. DST ON/OFF Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button twice more to advance to the

DST ON/OFF setting.

4. “DST” will appear above the indoor temperature/humidity display

and “ON”or “OFF” will flash above that.

5. Press and release the “OUT/+”button to select DST ON/OFF.

Note:

Some locations (Arizona and parts of Indiana) do not follow

Daylight Saving Time.

6. Press and release the “SET” button to confirm the DST ON/OFF

setting and continue to the radio-controlledTime ON/OFF setting.

E. Radio-ControlledTime ON/OFF Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button three more times to advance to

the radio-controlled time ON/OFF setting.

4. “RCC” will appear above the indoor temperature/humidity display

and “ON”or “OFF” will flash above that.

5. Press and release the “OUT/+”button to select radio-controlled time

ON/OFF setting.

6. Press and release the “SET”button to confirm the radio-controlled

time ON/OFF setting and continue to the 12/24-hour Time Mode

setting.

F. 12/24-hourTime Mode

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button four more times to advance to

the 12/24-hour time mode setting.

4. “12h” or “24h” will flash above the indoor temperature/humidity

display.

5. Press and release the “OUT/+”button to select 12 or 24-hour time

mode.

GB P.12 GB

P.13

Note:

In 12h mode “PM” will appear to the left of the time during PM

hours. If the time is not within the PM hours nothing will be displayed.

Be sure to set the time to the correct AM/PM time to ensure automatic

reception.

6. Press and release the “SET”button to confirm the 12/24-hour time

mode setting and continue to the Hour setting.

G. SettingThe Hour Manually

The WWVB signal will override any manual set time and date

information.The time will be based on the time zone selected.

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button five more times to advance to

the Manual Hour setting.

4. The hour will begin to flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired hour.

6. Press and release the “SET”button to confirm the hour setting and

continue to the Minute setting.

H. SettingThe Minutes Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button six more times to advance to

the Manual Minutes setting.

4. The minutes will begin to flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired minutes.

6. Press and release the “SET” button to confirm the minutes and

continue to theYear setting.

I. SettingTheYear Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button seven more times to advance

to the ManualYear setting.

4. The year will begin to flash below the time display.

5. Press and release the “OUT/+” button to select the desired year.

6. Press and release the “SET” button to confirm the year and con-

tinue to the Month setting.

J. SettingThe Month Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button eight more times to advance to

the Manual Month setting.

4. The Month will begin to flash below the time display.

5. Press and release the “OUT/+”button to select the desired month.

6. Press and release the “SET”button to confirm the month and con-

tinue to the Date setting.

K. SettingThe Date Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button nine more times to advance to

the Manual Date setting.

4. The date will begin to flash below the time display.

5. Press and release the “OUT/+”button to select the desired date.

6. Press and release the “SET” button to confirm the date and con-

tinue to the Temperature Measuring Units setting.

GB P.14 GB

P.15

L. Temperature Measuring Units Selection (˚F or ˚C)

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button ten more times to advance to

the Temperature Measuring Units setting.

4. °F or °C will flash at the top of the display.

5. Press and release the “OUT/+” button to select the desired tem-

perature-measuring unit.

6. Press and release the “SET” button to confirm the temperature-

measuring unit and continue to the Air Pressure Measuring Units

setting.

M. Air Pressure Measuring Units Selection (inHg/hPa)

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button eleven more times to advance

to the Air Pressure Measuring Units setting.

4. inHg or hPa will flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired air pres-

sure-measuring unit.

6. Press and release the “SET” button to confirm the air pressure-

measuring unit and continue to the Relative Pressure setting.

N. Relative Pressure Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button twelve more times to advance

to the Relative Pressure setting.

4. The barometric air pressure will flash in the middle of the display,

just below the forecast icon

5. Press and release the “OUT/+” or “IN” button to select the desired

relative air pressure value.

6. Press and release the “SET” button to confirm the relative pressure

setting and continue to the Forecast Sensitivity setting.

O. Forecast Sensitivity Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button thirteen more times to advance

to the Forecast sensitivity setting.

4. The two air pressure tendency arrows will begin flashing on either

side of the forecast icon and a flashing number will appear under

the forecast icon.

5. Press and release the “OUT/+”button to select the desired forecast

sensitivity setting.

GB P.16 GB

P.17

Note:

Barometric air pressure is usually reported as “relative air

pressure”.This reading is based on the combination of absolute air

pressure and altitude.In general, an increase in altitude will result in a

decrease in air pressure. Relative air pressure will make readings in

nearby locations relative to each other to allow for proper forecasting.

The absolute air pressure reading in the Weather Center cannot be

calibrated, only the relative air pressure.

6. Press and release the “SET” button to confirm the forecast sensi-

tivity setting.

THE MANUAL SETTING IS NOW COMPLETED

FEATURES AND OPERATIONS

A. Minimum and MaximumTemperature and Humidity

1. Indoor Minimum and Maximum Temperature and Humidity

The indoor weather station automatically stores the minimum and

maximum indoor temperature and humidity. The minimum and maxi-

mum values are updated automatically when a new minimum or maxi-

mum is recorded, or until manually reset.

a. From the normal display mode, press and release the “IN”key once

to view the indoor maximum temperature and humidity (“MAX” will

be displayed above the indoor temperature and humidity).

b. Press and release the “IN” key again to view the indoor minimum

temperature and humidity.

c. Press and release the “IN”key again to return to the normal mode

(timeout of viewing minimum/maximum values will occur if no keys

are pressed for fifteen seconds).

Note:

To reset the indoor minimum and maximum temperature and

humidity, first display the values you wish to reset (minimum or

maximum). Next press and hold the “SET” key for at least three

seconds. You will see then that the values will reset to the current

temperature and humidity and corresponding time.

2. Outdoor Minimum and MaximumTemperature

The indoor weather station automatically stores the minimum and

maximum outdoor temperature.The minimum and maximum values

are updated automatically when a new minimum or maximum is

recorded, or until manually reset.

a. From the normal display mode, press and release the “OUT/+”key

once to view the outdoor maximum temperature (“MAX” will be dis-

played above the outdoor temperature).

b. Press and release the “OUT/+” key again to view the outdoor mini-

mum temperature.

c. Press and release the “OUT/+” key again to return to the normal

mode (timeout of viewing minimum/maximum values will occur if

no keys are pressed for fifteen seconds).

Note:

To reset the outdoor minimum and maximum temperature, first

display the values you wish to reset (minimum or maximum). Next

press and hold the “SET”key for at least three seconds. You will see

then that the values will reset to the current temperature and corre-

sponding time.

B. Multiple RemoteTemperature Sensors

The WS-7394U-IT is able to receive signals from 2 additional tem-

perature sensors.The following are instructions for the set-up of tem-

perature sensor units with theWS-7394U-IT.These extra sensors can

be purchased through the same dealer as this unit.

1. Remove all the batteries from the receiver and sensor(s) and wait

60 seconds. During these 60 seconds, press any button 20 times

to discharge any excess power.

2. Insert the batteries to the first temperature sensor.

3. Within 2 minutes of powering up the first sensor, insert the batter-

ies to the Weather Station.Once the batteries are in place, all seg-

ments of the LCD will light up briefly. Following the indoor tempera-

ture and humidity, and the time as 12:00 will be displayed. If they

are not shown in LCD after 60 seconds, remove the batteries and

wait for at least 60 seconds before reinserting them.

4. The outdoor temperature from the first sensor (channel 1) should

then be displayed on the Weather Station. If this does not happen

and the signal reception icon is not shown, after 2 minutes, the

batteries will need to be removed from both units and reset from

step 1.

5. Insert the batteries to the second sensor as soon as the outdoor

temperature readings from the first sensor are displayed on the

Weather Station.

NOTE:

You must insert the batteries into the second sensor within 10

seconds of reception of the first sensor.

6. The outdoor temperature from the second sensor and the“channel

2” icon should then be displayed on the Weather Station. If this

does not happen after 2 minute, the batteries will need to be re-

moved from all the units and reset from step 1.

Andere Handbücher für Tomorrow's Weather Today WS-7394U-IT

Inhaltsverzeichnis

Sprachen:

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-3610 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C79790-11 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9025U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS9132 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84428 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3104U Bedienungsanleitung

La Crosse Technology

La Crosse Technology V15-AU Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7075UF Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9075TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7208TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology Tomorrow's Weather Today TX24U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9032U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9037U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX-440-TH Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1710 Abmessungen

La Crosse Technology

La Crosse Technology WW85777v2 Installationsanleitung

La Crosse Technology

La Crosse Technology WT-3131TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9153U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 512-807 Bedienungsanleitung

La Crosse Technology

La Crosse Technology The Weather Channel WS-8500TWC-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA79103 Abmessungen

La Crosse Technology

La Crosse Technology WS-9060U-IT Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung