La Crosse Technology WS-2310TWC Technisches Datenblatt

              

Quick Set Up Manual – WS-2310TWC Weather Station

Using cable connection or 433MHz for wireless transmission of weather data, this unique weather station can be powered

using batteries or AC power (or both at the same time) for all your weather needs in the home or office.

Carefully open and check that the following contents are complete:

Item: Consisting of: Fittings: Illustration:

Base Station 1) Main unit

1) AD/DC 120V power Adaptor -

optional use (included)

Thermo-Hygro

Sensor

1) Main unit

2) Rain protection cover

1) 32ft cable - optional connection to

the base station (included)

2) Wall mounting screws

3) Plastic anchors for screws

Wind Sensor 1) Main unit with wind vane

2) 32ft cable (already attached the

main unit)

3) Mast holder

1) 2 x U-bolts for mast holder

2) 4 x Washers

3) 4 x Nuts

4) 1 x screw (to secure main unit to the

mast holder)

Rain Sensor 1) Base and funnel

2) 32ft cable (already attached

the main unit)

‘Heavy

Weather” PC

software

CD-ROM

(English and German version only)

1) 6.5 ft computer cable for PC

function only - optional use

(included)

Setting Up:

Important: Operating power is supplied to both the wind and rain sensors by the thermo-hygro sensor

Battery Compartment

Setting up using batteries:

1) Sensors: Pull and remove the protective rain cover to reveal three socket ports and the battery cover. Insert the cables

of the wind and rain sensors in the correctly marked sockets. Slide open the battery compartment and checking the

correct polarity insert 2 x AA 1.5V batteries and replace the cover and rain cover

2) Base Station: Now open the battery cover at the back of the unit and checking the correct polarity insert 3 x AA 1.5V

batteries and replace the battery cover

Setting up using the AC/DC power adaptor:

1) Sensors: Set up the sensors as described above in Setting up using batteries.

2) Base Station: Using the AC power adaptor (included in this set) plug it into mains supply and connect it to the 6.0V DC

adaptor socket located at the side of the base station.

Performing a function test:

After powering up the units, the base station has to synchronize to the sensors before the weather data can be received.

The synchronization mode lasts for 15 minutes. Pressing the MIN/MAX key at any time will send the base station into the

WWVB radio controlled time reception mode. Under normal conditions the radio controlled time is usually received within 3-

5 minutes before returning to the normal operation. During the synchronization mode, perform the following function test to

check operation:

Thermo-Hygro Sensor

Battery Cover

Base Station

PC COM Port

DC 6.0V

socket

Socket for sensor

Battery compartment

Sensor sockets

1) Check that the wind-vane and fan of the wind sensor can freely rotate by moving the vane gently and also blowing into

the fan to emulate wind speed and direction

2) Holding the rain sensor in both hands with the longest side facing you, tilt the unit from side to side and hear the rain

counter flip which emulates rainfall

3) The base station will start to receive the 433MHz data transmitted from the sensors. Data such as rainfall will not be

updated as regularly as the outdoor temperature since it does not rain constantly all the time. Therefore these readings

may take up to two minutes before being shown on the LCD.

4) Now using the DISPLAY key on the base station, toggle between different weather modes on the LCD to check that the

weather readings can be received for the relevant sections, for example outdoor temperature and humidity and etc.

Note: Should any outdoor data not be received from the sensors (when “- - -“ is displayed), check all cables are correctly

inserted and/ or the batteries or AC cord are plugged in, press and hold the PLUS(+) key for 2 seconds to hear a beep and

the base station will synchronize to the sensors transmitting signal. Wind speeds that read zero does not mean reception

failure, it simply means that there was no wind at the time of reading the data.

Mounting the units:

Users must take their surroundings into consideration before deciding which method is best suited for them. Connection by

cable is advantageous in that data from the sensors to the base station is interference free. Using 433MHz wireless

transmission gives users little restriction on placement as that all units can be positioned virtually anywhere to within a 100ft

radius of the base station. You must decide which method is best suited to you. For cable connecting, please ensure that

the 10 meters cable included in this set meets with your distance requirements (see accessories in the main user manual for

adding extension cables).

To change from 433MHz to cable connection (or vice versa) simply connect (or disconnect) the 32ft cable from the base

station to the sensor. The base station will automatically detect the connection and read the weather data. If the data

cannot be received then press and hold the PLUS(+) key for 2 seconds to synchronize the base station with the sensor.

Important: Ensure all signals including the radio controlled time can be received and/or all cable distances meet with your

requirements at the point of fixing particularly before you start drilling any mounting holes.

Wind sensor

Secure the main unit to the shaft of the mast holder using the single screw provided with the front of the sensor (marked E)

facing in the East-West direction otherwise wind direction will not be accurate. Now fix the entire unit to a suitable mast

using the 2 two U-bolts, 4 washers and nuts found in this set.

Note: For best results mount the wind sensor onto a mast to allow the wind to freely travel from all directions to enable an

accurate reading (ideal mast size should be from Ø6.3” – Ø1.3”). Ensure that the 10 meter cable of the wind sensor meets

your distance requirements.

Rain sensor

The rain sensor should be mounted horizontally about 2-3ft off from the ground in an open area away from trees or other

coverings to allow rain to fall naturally for an accurate reading.

Note: For best results ensure the base is horizontal to allow maximum drainage of any collected rain

Thermo-hygro Sensor

To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall (2 screws are supplied), plug the sensor

firmly into the wall holder and then carefully replace the rain cover back over the thermo-hygro sensor.

Note: After mounting the units, should the weather data not be received then press and hold the PLUS(+) key for 2 seconds

to synchronize the base station with the sensor.

Weather station for use with your PC

Use your PC to read the latest weather data collected by the weather station. Just simply install the software from the

enclosed CD-ROM onto your PC. For full details see the “Heavy Weather “ PC software instructions in the CD-ROM

(English version only).

System Requirements:

The minimum system requirement for use of “Heavy Weather” PC software is:

• Operating system: Windows 98 or above

• Processor: Pentium 166 MHz or above processor

• RAM: 32MB or above

• Hard-disc: 20MB free space

• CD-ROM drive

Andere Handbücher für WS-2310TWC

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology C85845 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-1610TWC-IT Technisches Datenblatt

La Crosse Technology

La Crosse Technology V50AU Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6212 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1409BTV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA76669 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V40-PRO Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9057U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1409TH Abmessungen

La Crosse Technology

La Crosse Technology WS6282 Installations- und Betriebshandbuch

La Crosse Technology

La Crosse Technology WS-1516-IT Installationsanleitung

La Crosse Technology

La Crosse Technology WS-7211U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417v3 Abmessungen

La Crosse Technology

La Crosse Technology C87214 Installationsanleitung

La Crosse Technology

La Crosse Technology S85814V2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS6207 Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA86515 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7048U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1710v2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-1516-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1613-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8300U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2306 Bedienungsanleitung

La Crosse Technology

La Crosse Technology K84322 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung