La Crosse Technology WS-8300U Bedienungsanleitung

WS-8300U

915 MHz Wireless Weather Station

Instruction Manual

TABLE OF CONTENTS

Introduction……………………………………………………………………………………..3

Inventory of Contents…………………………………………………………………………4

Quick Set Up……………………………………………………………………………………4

Detailed Set Up………………………………………………………………………………4-5

Battery Installation…………..………………………………………………………..4-5

12 or 24 Hour Time Display………..…………………………………………………..5

Time Setting………..……..…………………………………………………………….5

Features……………………………………………………………………………………….6-7

Minimum & Maximum Temperature and Humidity……………………..……………6

Resetting Minimum & Maximum Temperature and Humidity………..…………….6

Adding Additional Thermo-Hygro Sensors……………………………..…………….6

Viewing & Operating with Multiple Thermo-Hygro Sensors……………………...6-7

Mounting………………………………………………………………………………………...7

Troubleshooting……………………………………………………………………………..7-8

Maintenance & Care ……………..…………………………………………………………...8

Specifications………………………………………………………………………………..8-9

Warranty Information……………………………………………………………………...9-10

FIGURE 1

INSTANT TRANSMISSION is the state-of-

the-art new wireless transmission

technology, exclusively designed and

developed by LA CROSSE TECHNOLOGY.

INSTANT TRANSMISSION offers you an

immediate update (every 4 seconds!) of all

your outdoor data measured from the

sensors: follow your climatic variations in

real-time!

This product offers:

12 or 24 Hour

Time Display

Indoo

Temperature

(

°F or °C

)

Connection w

Sensor Icon

Outdoo

Temperature

(°F or °C)

Outdoor

Humidity (%RH

)

MIN/MAX

Temperature

& Humidity

Low Battery

Indicator

INVENTORY OF CONTENTS

1. Wireless Weather Station (Figure 1)

2. Wireless Thermo-Hygro Sensor (TX21U)

and mounting bracket. (Figure 2)

3. 3 each, 1/2” Philips screws.

4. One strip of double sided adhesive tape.

5. Instruction Manual and Warranty Card.

ADDITIONAL EQUIPMENT

(not included)

1. 1 Philips screwdriver.

2. 4 Fresh “AA” 1.5VAlkaline Batteries.

QUICK SETUP

Hint: Use good quality Alkaline Batteries; avoid rechargeable batteries.

1. Have the Wireless Weather Station and thermo-hygro sensor 3 to 5 feet

apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the thermo-hygro sensor first and next into the

Wireless Weather Station.

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the Wireless Weather Station and the thermo-hygro sensor will begin to

communicate with each other, and the display will show both the indoor temperature

and an outdoor temperature. If the Wireless Weather Station does not display both

FIGURE 2

Wireless

Thermo-hygro

Senso

Mounting

Bracket

Set/Channel

Button

MIN/MAX / +

Button

temperatures after the 15 minutes, please retry the set up as stated above. After both

indoor and outdoor temperatures are displayed for 15 minutes you can place your

thermo-hygro sensor outdoors, and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote

temperature sensor has a range of 330 feet. Keep in mind that the 330 feet is in open

air with no obstructions and that radio waves DO NOT curve around objects. Actual

transmission range will vary depending on what is in the path of the signal. Each

obstruction (roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal range

in half.

Example: A wireless weather station receiver with a 330 feet range is mounted on an

interior wall, so that the signal has to pass through one interior wall, one exterior wall,

and across the 10 foot width of the room between the 2 walls. The first wall will reduce

the range to 165 feet, and the second wall will reduce the range to 87 feet. Factoring in

the 10 foot room, this leaves a maximum of 77 feet of remaining signal range.

This allowance is typically enough for a frame wall with non-metallic siding; however

certain materials can reduce range even further. Metal siding, stucco, and some types

of glass can reduce signal range by as much as ¾ or more, compared to the ½

reduction typical of most obstructions. It is possible to receive a signal through these

materials, however maximum range will be much less due to their tendency to absorb or

reflect a much larger portion of the sensor’s signal.

NOTE: Fog and mist will not harm your thermo-hygro sensor, but direct rain must be

avoided.

DETAILED SET UP GUIDE

I. BATTERY INSTALLATION (When one Thermo-hygro sensor is being used)

1. First, insert the batteries to the Thermo-hygro sensor (see “A. Thermo-hygro

sensor” below).

2. Within 2 minutes of powering up the sensor, insert the batteries to the

Temperature Station (see “B. Wireless Weather station” below). Once the

batteries are in place, all segments of the LCD will light up briefly. Following the

indoor temperature and the time as 12:00 will be displayed. If they are not shown

in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds

before reinserting them. Once the indoor data is displayed user may proceed to

the next step.

3. After the batteries are inserted, the Weather Station will start receiving data

signal from the sensor. The outdoor temperature and humidity should then be

displayed on the Weather Station. If this does not happen after 2 minutes, the

batteries will need to be removed from both units and reset from step 1 and the

signal reception icon is no longer shown.

A. THERMO-HYGRO SENSOR

1. Remove the Protective Rain Cover.

2. Remove the Battery Cover.

3. Observing the correct polarity, install 2 “AA” Alkaline Batteries—make sure they

do not spring free, or start-up problems may occur. Replace the Battery Cover.

B. WIRELESS WEATHER STATION

Note: After the batteries are installed, DO NOT press any buttons. This may interfere

with the signals, causing temperatures to register incorrectly.

1. Remove the Battery Cover on the back of the Wireless Weather Station.

2. Observing the correct polarity, install 2 “AA” Alkaline Batteries.

3. Replace Battery Cover.

4. Wait 15 minutes before pressing any buttons.

*When the signal is successfully received by the Weather Station, the icon will be

switched on. (If not successful, the icon will not be shown in LCD) So the user can

easily see whether the last reception was successful (icon on) or not (icon off). On the

other hand, the short blinking of the icon shows that a reception is being done now.

C. SELECTING 12 OR 24 HOUR TIME DISPLAY

1. Press and hold the SET/CH button for about 5 seconds.

Battery

Cover

Rain protection

cove

Battery

Compartment

Sensor signal

reception icon*

Battery

Compartment Battery

Cove

2. “12h” will begin to flash in the TIME section of the LCD

3. Press the MIN/MAX/+ button to toggle between “12h” and “24h” time.

Note:

•Selecting 12 hour time will automatically select °F as your temperature unit.

•Selecting 24 hour time will automatically select °C as your temperature unit.

4. Press and release the SET/CH button again to enter Time Setting.

D. TIME SETTING

1. After exiting the 12/24 Hour Setting, the hour will begin flashing in the time

display.

2. Press and release the MIN/MAX/+ button to select the desired hour.

Note: PM will appear to the left of the time display for PM hours. For AM hours, that

area will remain blank.

3. Press and release the SET/CH button again, and the minutes will begin to flash.

4. Press and release the MIN/MAX/+ button to select the desired minutes.

5. Press and release the SET/CH button to exit the SET UP mode.

Note: If no buttons are pressed for 10 seconds, the Wireless Weather Station will

automatically return to the normal display.

II. FEATURES

A. MINIMUM AND MAXIMUM TEMPERATURES AND HUMIDITY

1. Press and release the MIN/MAX button, “MIN” appears at the bottom of the LCD

and the recorded minimum temperatures and humidity are displayed.

2. Press and release the MIN/MAX button again to view maximum recorded

temperatures and humidity. “MAX” appears at the bottom of the LCD and the

maximum temperatures and humidity are displayed.

3. Press and release the MIN/MAX button once more to return to the current

temperatures and humidity.

B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES AND HUMIDITY

To reset both the minimum and maximum temperatures and humidity—press and

hold the MIN/MAX button for 5 seconds.

C. ADDING ADDITIONAL REMOTE SENSORS (OPTIONAL)

The WS-8300U is able to receive signals from 2 additional thermo-hygro sensors . The

following are instructions for the set-up of thermo-hygro sensor units with the WS-

8300U. These extra sensors can be purchased through the same dealer as this unit.

1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds.

During these 60 seconds, press any button 20 times to discharge any excess

power.

2. Insert the batteries to the first Thermo-hygro sensor.

3. Within 2 minutes of powering up the first sensor, insert the batteries to the

Weather Station. Once the batteries are in place, all segments of the LCD will

light up briefly. Following the indoor temperature and the time as 12:00 will be

displayed. If they are not shown in LCD after 60 seconds, remove the batteries

and wait for at least 60 seconds before reinserting them.

4. The outdoor temperature and humidity from the first sensor (channel 1) should

then be displayed on the Weather station. If this does not happen and the signal

reception icon is not shown, after 2 minutes, the batteries will need to be

removed from both units and reset from step 1.

5. Insert the batteries to the second sensor as soon as the outdoor temperature and

humidity readings from the first sensor are displayed on the Weather station.

NOTE: You must insert the batteries into the second sensor within 30

seconds of reception of the first sensor.

6. The outdoor temperature and humidity from the second sensor and the "channel

2" icon should then be displayed on the Weather station. If this does not happen

after 2 minute, the batteries will need to be removed from all the units and reset

from step 1.

7. Insert the batteries to the third sensor as soon as the "channel 2" icon and

outdoor data are displayed on the Weather station. Then within 2 minutes, the

channel 3 outdoor data from the third sensor will be displayed and the channel

icon will shift back to "1" once the third sensor is successfully received. If this is

not happen, user shall restart the setting up from step 1.

NOTE: You must insert the batteries into the third sensor within 30 seconds of

reception of the second sensor.

IMPORTANT: Transmission problems will arise if the setting for multiple

sensors is not followed as described above. Should transmission problems

occur, it is necessary to remove the batteries from all units and start again the

set-up from step 1.

D. VIEWING AND OPERATING WITH MULTIPLE REMOTE SENSOR UNITS

1. To view the temperature of a different thermo-hygro sensor unit, press and release

the SET/CH button. A shift from one “boxed” number to the next should be

observed on the right side of the OUTDOOR LCD.

2. To view the Minimum/Maximum temperature & humidity : first select from which

thermo-hygro sensor to read data (indicated by the “boxed” number). Pressing and

releasing the MIN/MAX button will toggle through the minimum and maximum

indoor temperature, and the minimum and maximum outdoor temperature and

humidity.

3. To reset the Minimum/Maximum readings, press and hold the MIN/MAX button for

5 seconds.

III. MOUNTING

Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We

recommend that you mount the thermo-hygro sensor on an outside North-facing wall

(under the eve of a house is ideal). The sending range is 330 feet; obstacles such as

walls, stucco walls, concrete, and large metal objects will reduce the range. Place the

Wireless Weather Station and thermo-hygro sensor in their desired locations before

permanently mounting.

A. THERMO-HYGRO SENSOR

1. Remove the mounting bracket from the thermo-hygro sensor.

2. Mount using either screws or adhesive tape.

3. Reattach the thermo-hygro sensor to the mounting bracket.

B. WIRELESS WEATHER STATION

1. The Wireless Weather Station comes with the table stand

attached to the back of the Receiver. If you wish to use the table-

stand, simply place the Wireless Weather Station in an appropriate

location, and pull out on the attached stand.

2. To wall mount, push the table stand flat against the Wireless

Weather Station (if it isn’t already flat). Fix a screw (not included)

into the desired wall, and place the Wireless Weather Station onto

the screw using the hanging hole on the backside. Gently pull the

Wireless Weather Station down to lock the screw into place.

TROUBLESHOOTING

NOTE: For problems not solved, please contact La Crosse Technology via e-mail or

phone, or visit our website, www.lacrossetechnology.com

Problem: The LCD is faint

Solution: Replace batteries

Problem: No outdoor temperature is displayed.

Solution:

1) Bring any units from outside, inside and place the units 3 to 5 feet apart with

nothing in-between them.

2) Remove the batteries from all units.

3) Press one of the buttons on the Wireless Weather Station display at least 20

times to clear all memory. Verify that the display is blank before proceeding.

4) Using good quality alkaline batteries, place the batteries back into the outdoor

temperature sensor; making sure they are installed according to the diagrams in

the battery compartment.

5) Taking care not to press any buttons, reinstall the batteries in the Wireless

Weather Station according to the diagram in the battery compartment.

6) Do not press any buttons for at least 15 minutes after installing the batteries.

(This is to let the units establish a good connection.)

7) During the course of the 15 minutes an outdoor temperature should appear on

the display. You can now put your sensor(s) back outside.

MAINTENANCE AND CARE

•Extreme temperatures, vibration, and shock should be avoided to prevent damage to

the units.

•Clean displays and units with a soft, damp cloth. Do not use solvents or scouring

agents; they may mark the displays and casings.

•Do not submerge in water.

•Do not subject the units to unnecessary heat or cold by placing them in the oven or

freezer.

•Opening the casings invalidates the warranty. Do not try to repair the unit. Contact

La Crosse Technology for repairs.

SPECIFICATIONS

Transmitting

Frequency 915 MHz

TEMPERATURE MEASURING RANGES

Indoor 14.1°F to 139.8°F with 0.2°F

resolution.

Outdoor -39.8 °F to 139.8°F with 0.2°F

resolution.

HUMIDITY MEASURING RANGE

Outdoor(%RH) 1% to 99%

Transmitting range Maximum 330 feet (100m) open

space

TEMPERATURE CHECKING INTERVAL

Indoor Every 15 seconds

Outdoor Every 4 seconds

BATTERIES—(Alkaline recommended)

Thermo-Hygro Sensor 2 x AA, 1.5V

Wireless Weather

Station 2 x AA, 1.5V

DIMENSIONS (H x W x D)

Receiver 5.47 x 5.47 x 0.94 in

(139 x 139 x 24 mm)

Thermo-Hygro

Sensor 5.34 x 2.26 x 2.24 in

(135.6 x 57.3x 62 mm)

Battery life Up to 24 Months (need to

confirmed!)

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology C87214 Installationsanleitung

La Crosse Technology

La Crosse Technology WS-7390U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS 9711 IT+ Installationsanleitung

La Crosse Technology

La Crosse Technology 302-604 Technisches Datenblatt

La Crosse Technology

La Crosse Technology WS-7136U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS1600IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7107U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1414M Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9730U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-141WBV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2510 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9625U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Temperature Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2308 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9029U Bedienungsanleitung

La Crosse Technology

La Crosse Technology V10-TH Abmessungen

La Crosse Technology

La Crosse Technology 327-1417 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology CA73453B Bedienungsanleitung

La Crosse Technology

La Crosse Technology Tomorrow's Weather Today WS-7394U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9049U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology V40-PRO Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21v4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9153TWC-IT Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung