La Crosse Technology WS-7016U Bedienungsanleitung

WS-7016U

Wireless 433 MHz

Temperature Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents 1

Additional Equipment 1

Quick Setup 2

Detailed Setup Guide

Battery Installation 3-6

Remote Control Sender 3-4

Indoor Temperature Station 5-6

Setting the Time 7-8

Selecting Units of Measurement 8

Features

Indoor Minimum and Maximum

Temperatures 9

Outdoor Minimum and

Maximum Temperatures 10-11

Resetting the Indoor Minimum

and Maximum Temperatures 11-12

Resetting the Outdoor Minimum

and Maximum Temperatures 12

Reading the Temperature Trend 13

Mounting

Remote Control Sender 13-16

Indoor Temperature Station 16-18

Using Multiple Remote Control Senders

Setup of Multiple Units 18-21

Viewing Remote Control

Senders 21-22

Features of the Multiple Remote

Control Senders 22-23

Troubleshooting 24-28

Maintenance and Care Instructions 28-29

Specifications 29-31

Warranty Information 31-33

FCC DISCLAIMER 34

INVENTORY OF CONTENTS

1. The Indoor Temperature Station (Figure 1)

2. The Outdoor Remote Control Sensor

(TX3U) and mounting bracket. (Figure 2)

3. 3 each, 1/2” Philips screws.

4. One strip of double sided adhesive tape.

5. Instruction Manual and Warranty Card.

ADDITIONAL EQUIPMENT (not included)

1. 1 Philips screwdriver.

2. 1 Flat screwdriver.

3. 2 Fresh AA 1.5V batteries.

4. 2 Fresh AAA 1.5V batteries.

QUICK SETUP

1. Insert two AAA batteries into the Remote

Control Sender.

2. Insert two AA batteries into the Indoor

Temperature Station.

Figure 1

Figure 2

3. Wait 5-6 minutes, or until the outdoor

temperature is displayed in the OUTDOOR

LCD (Liquid Crystal Display) of the Indoor

Temperature Station.

4. Set the Time (See complete instructions

for details).

5. Mount units.

Note: The Remote Control Sender transmits a

signal every 3 minutes. After the batteries have

been installed, the Indoor Temperature Station

searches for these signals for a duration of 6

minutes. If there is no temperature reading in

the OUTDOOR LCD after 6 minutes, make

sure the units are within range of each other, or

repeat battery installation process.

DETAILED SETUP GUIDE

I. BATTERY INSTALLATION

A. REMOTE CONTROL SENDER

1. Remove the mounting bracket.

The bracket snaps on and off with

minimal effort.

2. Remove battery cover. To do this,

remove the flathead screw located

in the lower-central position of the

unit. The rubber weather-seal

creates a tight seal for the battery

cover, and does not allow the

battery cover to fall away from the

Battery cover

Battery compartment

unit. Place the screw partially back

into the hole and angle it slightly,

so the threads grab the battery

cover. With the screw, pull the

battery cover off.

3. Observing the correct polarity,

install 2 AAA batteries. The

batteries will fit tightly—make

sure they do not spring free, or

start-up problems may occur.

4. Check the LCD screen of the

Remote Control Sender to see if

there is a temperature reading. If

there is no reading check the

polarity of the batteries or replace

with new batteries.

5. Observing that the rubber

weather-seal is in place; replace

battery cover, screw, and

mounting bracket.

B. INDOOR TEMPERATURE

STATION

Note: After the batteries are installed, DO

NOT press any buttons. This may interfere

with the signals, causing temperatures to

1. Remove the battery cover on the

backside. To do this, push up and

pull out.

Battery

Cover

2. Observing the correct polarity,

install 2 AA batteries.

3. Replace battery cover.

4. Wait 5-6 minutes or until both

indoor and outdoor temperatures

are shown on the Indoor

Temperature Station.

5. The Indoor Temperature Station

should now show: “-:- -” in the

TIME LCD, and temperatures in

the INDOOR and OUTDOOR

LCD’s.

TIME LCD

INDOOR LCD

OUTDOOR LCD

II. TIME

A. SETTING THE TIME

1. Press and hold the SET button for

1 second. “12h” will appear in the

TIME LCD.

2. Use the INDOOR button to select

either 12h time or 24h time (12h is

an AM—PM mode, and 24h is

military time).

3. Press the SET button 2 times,

“TIME” will flash in the upper left

corner.

4. Press the INDOOR button to set

the hours, and press the

OUTDOOR button to set the

minutes.

Control Buttons

5. Press the SET button to activate

the clock.

Note: There is only a “PM” display,

which appears under “TIME.” If there

is no display here it is AM. Make sure

you set the time accordingly.

III. UNITS OF TEMERATURE MEASURE

A. SELECTING UNITS OF

MEASUREMENT

1. Press and hold the SET button for

1 second.

2. Press the SET button again. “F”

will appear in the TIME LCD.

3. Press the INDOOR button to shift

between F and C.

4. Press the SET button twice to

activate settings.

IV. FEATURES

A. INDOOR MINIMUM AND

MAXIMUM TEMPERATURES

1. Press and hold the INDOOR

button for 1 second. “MIN”

appears in the INDOOR LCD and

the recorded minimum

temperature is displayed.

2. Press and hold the INDOOR

button for 1 second. “MAX”

appears in the INDOOR LCD and

the recorded maximum

temperature is displayed.

Note: When first setting-up the

minimum and maximum temperatures

may be the same as the current

temperatures.

3. To return to the current

temperature, press and hold the

INDOOR button for 1 second.

B. OUTDOOR MINIMUM AND

MAXIMUM TEMPERATURES

1. Press and hold the OUTDOOR

button for 1 second. “MIN”

appears in the OUTDOOR LCD.

The “OUTDOOR MIN,” and

“TIME” displays will flash. The

recorded minimum temperature is

displayed in the OUTDOOR LCD,

and the time it was recorded is

displayed in the TIME LCD.

After 15 seconds the “OUTDOOR

MIN,” and “TIME” will stop

flashing. However, the minimum

outdoor temperature will continue

to be displayed.

2. Press and hold the OUTDOOR

button for 1 second. “MAX”

appears in the OUTDOOR LCD.

The “OUTDOOR MAX,” and

“TIME” displays will flash. The

recorded maximum temperature is

displayed in the OUTDOOR LCD,

and the time it was recorded is

displayed in the TIME LCD.

After 15 seconds the “OUTDOOR

MAX,” and “TIME” will stop

flashing, and the maximum

outdoor temperature will continue

to be displayed.

3. To return to current temperature,

press and hold the OUTDOOR

button for 1 second.

V. RESETTING THE MINIMUM AND

MAXIMUM TEMPERATURES

A. INDOOR

1. To reset both the minimum and

maximum temperatures—press

and continue to hold the INDOOR

button, while you press and hold

the RESET button. When the

temperatures are reset release the

buttons.

2. To return to the current indoor

temperature, press and hold the

INDOOR button two times,

holding for 1 second each.

B. OUTDOOR

1. To reset both the minimum and

maximum temperatures—press

and continue to hold the

OUTDOOR button, while you

press and hold the RESET button.

When the temperatures are reset

release the buttons.

2. To return to the current outdoor

temperature, press and hold the

OUTDOOR button two times,

holding for 1 second each.

VI. READING THE TEMPERATURE

TREND

A. The temperature trend indicator is

displayed in the OUTDOOR LCD.

1. Indicates that the temperature

is rising.

2. Indicates that the temperature

is dropping.

3. The absence of an arrow indicates

that the temperature is stable.

VII.MOUNTING

A. THE REMOTE CONTROL

SENDER

Note: To achieve a true temperature

reading, avoid mounting where direct

sunlight can reach the Remote Control

Sender. We recommend that you mount the

Sender on a North-facing wall. The sending

range is 80ft; obstacles such as walls,

concrete, and large metal objects can

reduce the range. Place both units in their

desired location before permanently

mounting the Remote Control Sender.

There should be a change of temperature in

the OUTDOOR LCD within 6 minutes.

The Remote Control Sender can be mounted in

two ways:

with the use of screws or,

using the adhesive tape.

1. MOUNTING WITH THE

SCREWS

a) Remove the mounting bracket

from the Remote Control

Sender (figure 2).

b) Place mounting bracket over

desired location. Through the

three screw holes of the

bracket, mark the mounting

surface with a pencil.

c) Where marked, drill holes

into mounting surface using

an appropriate size drill bit.

d) Screw mounting bracket onto

the mounting surface. Ensure

that the screws are flush with

the bracket.

2. MOUNTING WITH

ADHESIVE TAPE

a) With a nonabrasive solution,

clean and dry the back of the

mounting bracket and the

mounting surface to ensure a

secure hold. The mounting

surface should be smooth and

flat.

b) Remove the protective strip

from one side of the tape.

Adhere the tape to the

designated area on the back of

the mounting bracket.

c) Remove the protective strip

from the other side of the

tape. Position the Remote

Control Sender in the desired

location, ensuring that the

Indoor Temperature Station

can receive the signal.

B. THE INDOOR TEMPERATURE

STATION

Note: Before mounting the Indoor

Temperature Station make sure that it is

able to receive signals from the Remote

Control Sender.

The Indoor Temperature Station can also

be mounted in two ways:

with the table stand or,

on the wall with the use of a wall

hanging screw (not included).

1. USING THE TABLE-STAND

a) The Indoor Temperature

Station comes with the table

stand already mounted. If you

wish to use the table-stand all

that is required is to place the

Indoor Temperature Station in

an appropriate location.

2. WALL MOUNTING

a) Remove the table stand. To

do this, pull down on the

stand from the rear and rotate

forward.

b) Fix a screw (not included)

into the desired wall, leaving

approximately 3/16 of an inch

(5mm) extended from the

wall.

c) Place the Indoor Temperature

Station onto the screw using

the hanging hole on the

backside. Gently pull the

Station down to lock the

screw into place.

VIII. USING MULTIPLE REMOTE

CONTROL SENDERS

Your WS-7016U Indoor Temperature Station

can receive signals from five different Remote

Control Senders (The TX3U features

temperature data transmission and the TX3UP

offers the same plus a 10’ probe to insert in a

pool, spa, soil, etc.). Assign a number to each

Remote Control Sender (i.e. #1 will be for

outdoors, #2 will be for the basement, etc.).

This will help you determine which

temperature, from which Sender, you are

reading on the Indoor Temperature Station.

Note: When setting up multiple units it is

important to insert batteries first into all the

Remote Control Senders, and in numeric

sequence. Second install batteries into the

Indoor Temperature Station. Transmission

problems will arise if this is not done correctly

and if the total time for set-up exceeds 6

minutes.

A. UP OF MULTIPLE UNITS

1. It is necessary to remove the

batteries from all existing units in

operation.

2. Remove the battery covers to all

Remote Control Senders. See

section I.A.2.

3. Place all Remote Control Senders

in sequential order.

#1 #2 #3

4. In sequential order, install

batteries. (Refer to instructions in

I.A.3 through I.A.5).

5. Install batteries into the Indoor

Temperature Station. (Refer to

instructions in I.B.).

6. Follow directions in section II.A

to set the time, section III.A to

select Fahrenheit or Celsius, and

section VII. A to mount.

B. VIEWING MULTIPLE REMOTE

CONTROL SENDERS ON THE

INDOOR TEMPERATURE

STATION

1. To view the temperature of a

different Remote Control Sender,

press the RESET button.

2. In the OUTDOOR LCD a

should shift and become a

This indicates that you are 2

now reading the temperature of

the Remote Control Sender you

designated as #2.

3. Repeat step 1 to view the 3rd, 4th,

and 5th (depending on how many

are set up) temperatures sent by

the Remote Control Senders.

Continue to press RESET until you

return to the first Remote Control

Sender.

C. VIEWING THE FEATURES OF

MULTIPLE REMOTE CONTROL

SENDERS

1. Press the RESET button to select

the Remote Control Sender you

wish to view.

2. To view the OUTDOOR

MINIMUM AND MAXIMUM

TEMPERATURES, follow

directions in section IV.B. While,

in this mode press the RESET

button to toggle through different

Remote Control Senders and view

their minimum and maximum

temperatures.

3. To reset the OUTDOOR

MINIMUM AND MAXIMUM

TEMPERATURES, follow step 1

above and the directions in

sections V.A. through V.B. This

will reset the minimum and

maximum for only the selected

Remote Control Sender.

TROUBLESHOOTING

Problem Solution

“--. -” appears in

the OUTDOOR

LCD of the Indoor

Temperature

Station.

Batteries may be inserted wrong in

Remote Control Sender—correct the

polarity

The batteries may be weak—replace

with new batteries.

The Remote Control Sender may be

out of its 80 foot (25m) range—bring

the units closer together.

“--.-” appears in

the OUTDOOR

LCD of the Indoor

Temperature

Station.

(continued)

Obstacles such as walls, concrete,

metal window frames, or large metal

objects, may be obstructing signal

transmission from the Remote Control

Sender—Relocate the Remote Control

Sender, within range, where there are

no obstructions.

Other equipment in vicinity operating

on 433MHz may interfere with

signal—turn off other equipment or

relocate Indoor Temperature Station,

wait a few minutes for signal to be

found.

Temperature exceeds range of the

Remote Control Sender—see

specifications for range.

No temperature in

the LCD of the

Remote Control

Sender.

The batteries may be inserted wrong

or weak—check the polarity of

batteries or replace with new batteries.

Remote Control Sender out of its 80

foot (25m) range—bring the units

closer together.

If problem persists contact La Crosse

Technology for replacement.

The LCD of the

Indoor

Temperature

Station is blank.

Check for proper battery installation.

The batteries may be weak—replace

with new batteries.

The LCD of the

Indoor

Temperature

Contact La Crosse Technology for

replacement.

Station is blank.

(continued)

Temperature is

“incorrect” Temperatures can vary depending on

the location of the Remote Control

Sender. The thermometers are not

100% accurate (the WS-7016U is

accurate to +/- 2 F). If you are sure

the temperature is wrong (the unit

reads 110 F, when it is actually 70

F) reset entire system by removing

all batteries and following set-up

instructions. If this does not solve the

problem, contact La Crosse

Technology for replacement.

Problem not

covered under the

warranty (ie.

Dropped unit into

water).

Call La Crosse Technology to order

replacement part. We will accept Visa,

MasterCard, Discover, or prepayments

by check.

MAINTENANCE AND CARE

INSTRUCTIONS

Extreme temperatures, vibration, and shock

should be avoided to prevent damage to the

units.

Clean displays and units with a soft, damp

cloth. Do not use solvents or scouring

agents; they may mark the displays and

casings.

Do not submerge in water.

Do not subject the units to unnecessary

heat or cold by placing them in the oven or

freezer.

Opening the casings invalidates the

warranty. Do not try to repair the unit.

Contact La Crosse Technology repairs.

SPECIFICATIONS

Transmitting Frequency 433MHz

Recommended Operating Temperature

Indoor Temperature

Station 32F to 122F

(0C to 50C)

Remote Control Sender 14F to 140F

(-10C to 60C)

Measuring Temperatures

Temperature Station:

Indoor -20.2F to 156.2F with 0.2F

resolution.

(-29.0C to 69.0C with 0.1C

resolution).

Temperature Station:

Outdoor -21.8F to 156.2F with 0.2F

resolution.

(-29.9C to 69.0C with 0.1C

resolution).

Remote Control Sender

-21.8F to 156.2F with 0.2F

resolution.

(-29.9C to 69.0C with 0.1C

resolution).

Accuracy

Indoor +/- 2F (+/- 1C).

Outdoor +/- 2F (+/- 1C).

Transmitting range of

the Remote Control

Sender

Maximum 80 feet (25m).

Temperature check

Indoor Temperature Every 10 seconds.

Station: Indoor

Indoor Temperature

Station: Outdoor Three times in 10 minutes.

Remote Control Sender

(LCD) Once every minute.

Batteries—(Alkaline recommended)

Remote Control Sender 2 x AAA, 1.5V

Indoor Temperature

Station 2 x AA, 1.5V

Battery life expectancy

for both units Approximately 1 year.

Dimensions: (L x W x H)

Indoor Temperature

Station 3.51 x 1.19 x 4.88 in.

(excluding table stand)

(90x30.5x125mm).

Remote Control Sender

2.18 x 0.94 x 3.12 in.

(56x24x80mm).

Andere Handbücher für WS-7016U

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-7049 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C79790 Abmessungen

La Crosse Technology

La Crosse Technology WS-7038U Bedienungsanleitung

La Crosse Technology

La Crosse Technology T85647 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-146v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7013BZ Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7091 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9611U-IT Handbuch

La Crosse Technology

La Crosse Technology 328-1414 Bedienungsanleitung

La Crosse Technology

La Crosse Technology SW404 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 328-1415 Installationsanleitung

La Crosse Technology

La Crosse Technology WS-9009U Bedienungsanleitung

La Crosse Technology

La Crosse Technology The Weather Channel WS-8500TWC-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21V3 Abmessungen

La Crosse Technology

La Crosse Technology WS-9046U Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology T85647 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1409 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 9245 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA79103 Abmessungen

La Crosse Technology

La Crosse Technology WS-2816U-IT Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung