La Crosse Technology WS-7075UF Bedienungsanleitung

WS-7075U

Wireless 433 MHz

Radio-controlled Weather Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 3-4

Quick Set-Up Guide 4

Detailed Set-Up Guide

Battery Installation 4-5

Program Mode

Function Keys 6

12/24 hour Time Setting 6

Time Zone Setting 6-7

Daylight Saving Time Setting 7

Time Setting (WWVB & Manual) 8-9

Setting Day, Date, and Year 9-10

Selecting °F or °C 10

Setting the LCD Contrast 10

Features

Weather Forecast Icons 11-12

Indoor Temperature, Humidity, & Comfort

Level Indicator

Outdoor Temperatures 13

Minimum & Maximum Records (Indoor,

Outdoor, & Resetting)

13-14

Alarm (Setting, Snoozing, & Stopping) 14-15

Additional Remote Control Sending Units

(Set-Up, Viewing, & Operation)

15-16

Mounting 17-18

Troubleshooting 19

Maintenance & Care 20

Specifications 21

Warranty Information 22

INVENTORY OF CONTENTS

1. The Weather Station (Figure 1).

2. One TX3U Remote Control Sender with mounting bracket (Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction Manual and Warranty Card.

ADDITIONAL EQUIPMENT (not included)

Holder

Mounting

Bracket

Figure 2

Outdoor LCD

Indoor LCD

Forecast LCD

Date LCD

Time LCD

Figure 1

1. Two, fresh AA 1.5V batteries.

2. Two, fresh AAA 1.5V batteries.

3. One, Philips screwdriver.

4. One, Flat screwdriver.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal

can be received up to 2, 000 miles away through the internal antenna in the Weather

Station. However, due to the nature of the Earth’s Ionosphere, reception is very

limited during daylight hours. The Weather Station will search for a signal every

night when reception is best. The WWVB radio station derives its signal from the

NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is

continually measuring every second, of every day, to an accuracy of ten billionths of

a second per day. These physicists have created an international standard,

measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

QUICK SET-UP GUIDE

1. Insert two AAA batteries into the Remote Control Sender.

2. Insert two AA batteries into the WEATHER STATION.

3. Wait 5 minutes, or until the outdoor temperature is displayed in the

OUTDOOR LCD (Liquid Crystal Display).

4. Wait 6-10 minutes (in ideal reception conditions) for the WWVB time

to be displayed in the TIME LCD. If the WWVB takes longer to set,

you may manually set the time (see complete instructions), or you can

wait until after the weather station conducts its programmed search at

the ideal reception time period of 12:00am to 6:00am.

5. Mount the units, ensuring that all units are sending and receiving

signals.

Note: The Remote Control Sender transmits a signal every 3 minutes; after

the batteries have been installed, the Weather Station will search for the

signal for a duration of 5 minutes. If there is no temperature reading in the

OUTDOOR LCD after 5 minutes, make sure the units are within range of

each other, or repeat the battery installation procedure.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE CONTROL SENDER

1. Remove the mounting bracket. The bracket snaps on and off

easily.

2. Remove the battery cover, by

removing the Flathead screw

located on the backside of the

unit, in the lower-central position.

The rubber weather-seal creates a

tight seal for the battery cover,

and does not allow the battery

cover to fall away from the unit. Place the screw partially

Battery

Cover

back into its hole, and angle it slightly—so the threads grab

the battery cover. With the screw, pull the battery cover off.

3. Observing the correct polarity install 2 AAA batteries. The

batteries will fit tightly (to avoid start-up problems make sure

they do not spring free).

4. Check the LCD screen of the Remote Control Sender to see if

there is a temperature reading. If there is no reading, check

the polarity of the batteries or replace with new batteries.

5. Check to make sure that the rubber weather-seal is in place,

and replace the battery cover, screw, and mounting bracket.

B. WEATHER STATION

1. Remove the battery cover. To do

this, insert a solid object in the space

provided at the lower-central position

of the battery cover, then push up and

pull out on the battery cover.

Battery

Cover

2. Observe the correct polarity, and

install 2 AA batteries.

3. Replace the battery cover.

Note: Immediately after the batteries have been installed, each

LCD (Liquid Crystal Display) will flash, and a tone will sound.

Within a few seconds the indoor temperature, indoor relative

humidity, and the weather icons (sun and clouds) will be

displayed. If not, then remove batteries for 10 seconds and

reinstall. If the outdoor temperature is not displayed within four

minutes, remove batteries from both units, wait 10 seconds, and

reinstall. The time will show -:-- and start searching for the

signal. If it successfully receives the time signal (usually at night),

it will display the correct time (default is Eastern).

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or either the IN or

the OUT buttons are pressed during programming modes the unit will

confirm/set the last information entered—the display will stop flashing and

return to normal time-date readings. If you don’t leave the program mode

during the programming of sections III through VIII, you can advance to

step 3 of the next program setting. If you do leave the program setting (or

want to program a specific setting) follow each instructional step to

program that setting.

I. FUNCTION KEYS

The Secondary Buttons are located directly below the Primary Buttons, and

behind the La Crosse Technology shield on the face of the unit. To access

the Secondary Buttons: place a solid object in the slot (above the shield)

and gently pull out and down.

Secondary Buttons

Primary Buttons

II. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 3 seconds, or until “12 h”

flashes in the DATE LCD.

2. Press the CH button to toggle between 12 and 24-hour time.

3. Press the SET button to confirm the 12/24-hour setting, and to

advance to Time Zone Setting.

III. TIME ZONE SETTING

The default time zone is EST, “-5hr” (Eastern Standard Time), to

change this setting:

1. Press and hold the SET button for 3 seconds, or until “12 h”

OR “24 h” flashes in the DATE LCD.

2. Press the SET button 1 more time to enter the Time Zone

setting mode. The default Time Zone “-5” will flash in the

DATE LCD.

3. Select your appropriate time zone using the CH button.

During selection of the Time Zone, the 3 letter abbreviations

for the time zones found in North America will flash across

the top of the TIME LCD. Observe the chart below, showing

the corresponding abbreviations, time zones, and codes.

TIME ZONES

GMT 0

Atlantic -4

EST; Eastern -5

CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

Note: There are more time zones represented by numbers than there are

represented by 3 letter abbreviations. If you live in North America you

need only be concerned with the ones in the chart above.

4. Press the SET button to confirm, and advance to the Daylight

Saving Time setting.

IV. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 3 seconds, or until “12 h” or

“24 h” flashes in the DATE LCD.

2. Press the SET button 2 more times to reach the DST selection

mode. “DST 1” is the default setting and will be flashing in

the DATE LCD.

3. Press the CH button to select “DST 0” or “DST 1.”

4. “DST 0” indicates that the feature is off and the WWVB will

not change times automatically. “DST 1” indicates that the

feature is on and the WWVB will change times automatically.

Note: Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST 0.”

5. Press the SET button to confirm and advance to the Time

setting mode.

V. TIME

There are two methods by which the time can be set:

A) Automatically via WWVB reception, or

B) Manually.

A. WWVB (Remote Control Time)

This method requires you to do nothing, except wait for the signal

to be received, and to select a time zone. Reception usually takes

approximately 6-10 minutes during optimal conditions. The best

conditions for reception is at night, between midnight and 6:00

am—when there is less atmospheric interference. To keep your

time as accurate as possible, the Weather Station conducts a

WWVB search every night between these hours, and overrides any

manually set time. The WWVB tower icon (appearing in the TIME

LCD) will flash when a signal-search is in progress, will remain

steady when the signal has been received, and nothing will be

displayed in all other situations. If the WWVB time has not been

received after 10 minutes of battery installation, you may manually

set the time or leave the time function alone (reception will occur

regardless).

B. MANUAL TIME SETTING

1. Press and hold the SET button for 3 seconds or until “12h”

flashes in the DATE LCD.

2. Press the SET button 3 more times (until the hour digit

flashes in the TIME LCD).

3. Press the CH button to change the hour. Press the CH button

once and the hour will increase by one, twice and the hour

will increase by two, etc.

4. Press the SET button to confirm the hour setting, and to

advance to the minute setting mode.

5. The minute digits should be flashing. Press the CH button to

change the minutes—increasing the minutes by increments of

1 with each press of the CH button.

6. Press the SET button to confirm the minutes and to advance to

the Day, Date, and Year setting mode.

Note: In 12h mode, “PM” will appear to the left of the time

during PM hours. If the time is not within the PM hours, nothing

will be displayed. Be sure to set the time to the correct AM/PM

time to ensure automatic reception at optimal times.

VI. SETTING THE DAY, DATE, AND YEAR

1. Press and hold the SET button for 3 seconds, or until “12 h” or

“24 h” flashes in the DATE LCD.

2. Press the SET button 5 more times to reach the Weekday

setting mode.

Note: “MO” (representing Monday) is the default setting for the

weekday, “1.1” is the default setting for the numeric month and

day, and “1999” is the default setting for the year. The day, date,

and year will be automatically set once the WWVB signal is

received. However, the day, date, and year can be manually set

and will flash respectively in the DATE LCD during manual

programming.

3. The weekday will be flashing in the DATE LCD, press the

CH button to change the weekday.

4. Press the SET button to confirm, and to enter the numeric-

month setting mode.

5. The numeric-month will be flashing in the DATE LCD. Use

the CH button to set to the current month.

6. Press the SET button to confirm the numeric-month, and to

enter the numeric-day setting mode.

7. The numeric-day will be flashing, use the CH button to set the

current day.

8. Press the SET button to confirm and to enter the year setting

mode.

9. The default-year will be flashing, use the CH to set the

appropriate year.

10. Press the SET button to confirm and to advance to the °F or °C

setting mode.

VII. SELECTING °F OR °C

1. Press and hold the SET button for 3 seconds, or until “12h” or

“24h” flashes in the DATE LCD.

2. Press the SET button 9 times to reach the °F or °C setting

mode.

3. “°F” is the default setting, and should be flashing in the

DATE LCD.

4. Press the CH button to shift °F to °C, and back.

5. Press the SET button to confirm your selection, and to

advance to the LCD contrast setting.

VIII. SETTING THE LCD CONTRAST

1. Press and hold the SET button for 3 seconds, or until “12h” or

“24h” flashes in the DATE LCD.

2. Press the SET button 10 more times to reach the LCD contrast

setting mode.

3. The default setting—“Lcd 5”—will flash in the DATE LCD.

4. There are 8 LCD contrast levels to choose from—“Lcd 0” is

the lightest, and “Lcd 7” is the darkest.

5. Press the CH button to toggle through the settings.

6. Press either the IN or OUT buttons to confirm all the settings

and to exit the manual-programming mode (or wait 15

seconds for the unit to automatically return to the normal

display mode).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS7034UITCA Bedienungsanleitung

La Crosse Technology

La Crosse Technology K86319 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6890 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology TX141TH-B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7395U Bedienungsanleitung

La Crosse Technology

La Crosse Technology DCF-77 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1711BL Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9124U-IT-CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology S85814 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS6206 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WA-1030U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9066U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1710 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8015TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2308AL Bedienungsanleitung

La Crosse Technology

La Crosse Technology WEATHER DIRECT WD-3105 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415V3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7136U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7047U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1913U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology S88907V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1611T Bedienungsanleitung

La Crosse Technology

La Crosse Technology V22-WRTH Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung