La Crosse Technology WS-9124TWC-IT Bedienungsanleitung

Contents

Language Page

_______________________________________________

English 1

French 47

Spanish

WIRELESS 915 MHz TEMPERATURE STATION

Instruction Manual

INTRODUCTION:

Congratulations on purchasing this compact 915MHz Wireless

Temperature Station which displays time, indoor temperature,

outdoor temperature and indoor humidity readings. With two easy to

use keys, this product is ideal for use in the home or office.

INSTANT TRANSMISSION is the state-

of-the-art new wireless transmission

technology, exclusively designed and

developed by LA CROSSE

TECHNOLOGY. INSTANT

TRANSMISSION offers you an

immediate update (every 16 seconds!)

of all your outdoor data measured

from the transmitters: follow your

climatic variations in real-time!

This product offers:

FEATURES:

The Temperature Station

•Quartz clock in 12 or 24-hour time display (hour and minute,

manually set)

•Indoor and outdoor temperature reading in Fahrenheit (°F) or

Celsius (°C)

•Indoor humidity reading in %RH

•Wireless transmission at 915 MHz

•Signal reception intervals at 16-second

•Minimum and Maximum records of indoor temperature,

indoor humidity and outdoor temperature

•Low battery indicator

•Wall mounting or table standing

(table stand included)

The Outdoor Temperature Sensor

•Remote transmission of outdoor

temperature to Temperature Station

by 915 MHz

•Water-resistant casing

LCD

Display

Function

Keys

Hanging

Hole

Battery

compartment

cover

Removable

stand

•Wall mounting case (Mount in a sheltered location. Avoid direct

rain and sunlight)

SETTING UP:

When one sensor is used

1. First, insert the battery into the temperature sensor. (see “Install

and replace batteries in the temperature sensor“).

2. Immediately after and within 30 seconds, insert the batteries into

Temperature Station (see “Install and replace batteries in the

Temperature Station”). Once the batteries are in place, all

segments of the LCD will light up briefly. Following the time as

12:00 and the indoor temperature will be displayed. If these are

not displayed after 60 seconds, remove the batteries and wait for

at least 10 seconds before reinserting them.

3. After inserting the battery into the sensor, the Temperature

Station will start receiving data from the sensor. The outdoor

temperature and the signal reception icon should then be

displayed on the Temperature Station. If this does not happen

after 3 minutes, the batteries will need to be removed from both

units and reset from step 1.

4. In order to ensure sufficient 915 MHz transmission there should

be a distance of no more than 330 feet (100 meters) between the

final position of the Temperature Station and the sensor (see

notes on “Mounting” and “915 MHz Reception”).

When more than one sensor is to be used

1. User shall remove all the batteries from the Temperature Station

and sensors and wait 60 seconds if setting has been done with one

sensor before.

2. Insert the batteries to the first sensor.

3. Within 30 seconds of powering up the first sensor, insert the

batteries into to the Temperature Station. Once the batteries are in

place, all segments of the LCD will light up briefly. Following time as

12:00 and the indoor temperature will be displayed. If they are not

shown in LCD after 60 seconds, remove the batteries and wait for

at least 60 seconds before reinserting them.

4. The outdoor temperature from the first sensor (channel 1) should

then be displayed on the Temperature Station. Also, the signal

reception icon will be displayed. If this does not happen after 2

minutes, the batteries will need to be removed from both units and

reset from step 1.

5. Insert the battery into the second sensor immediately after (within

10 seconds after) inserting battery to the Temperature Station.

6. The outdoor temperature from the second sensor and the "channel

2" icon should then be displayed on the Temperature Station. If this

does not happen after 2 minute, the batteries will need to be

removed from all the units and reset from step 1.

7. Insert the batteries into the third sensor immediately after (within

10 seconds after) inserting battery to the second sensor.

8. Then within 2 minutes, the channel 3 outdoor data from the third

sensor will be displayed and the channel icon will shift back to "1"

once the third sensor is successfully received. If this is not happen,

user shall restart the setting up from step 1.

9. In order to ensure sufficient 915 MHz transmission there should be

a distance of no more than 330 feet (100 meters) between the final

position of the Temperature Station and the sensor (see notes on

“Mounting” and “915 MHz Reception”).

Note:

After the three sensors have been set up, user may need to check the

readings displayed on the Temperature Station against those being shown

on the sensor displays, in order to recognize which channel each sensor is

displayed.

If the signal reception is not successful on the first frequency (915MHz) for

45 seconds, the frequency is changed to 920MHz and the learning is tried

for another 45 seconds. If still not successful the reception is tried for 45

seconds on 910MHz. This will also be done for re-synchronization.

IMPORTANT:

Transmission problems will arise if the setting for additional sensors is not

followed as described above. Should transmission problems occur, it is

necessary to remove the batteries from all units and follow the set-up from

step 1.

HOW TO INSTALL AND REPLACE BATTERIES IN THE

TEMPERATURE STATION

The Temperature Station uses 2 x AAA, 1.5V

Alkaline batteries. When batteries will need to

be replaced, the low battery icon will appear

on the LCD. To install and replace the

batteries, please follow the steps below:

1. Lift up the battery compartment cover.

2. Insert batteries observing the correct

polarity (see marking).

3. Replace compartment cover.

HOW TO INSTALL AND REPLACE

BATTERIES IN THE

TEMPERATURE SENSOR

The temperature sensor uses 1 x CR2023, 3.0V

battery. When battery needs replacing, the low battery

icon will appear on the LCD of the Temperature

Station. To install and replace the batteries, please

follow the steps below:

1. Remove the battery compartment cover at the

back of the sensor.

2. Insert the batteries, observing the correct polarity (see

marking).

3. Replace the battery cover on the unit.

Note:

In the event of changing batteries in any of the units, all units need

to be reset by following the setup procedures. This is because a

random security code is assigned by the sensor at start-up and this

code must be received and stored by the Temperature Station in the

first few minutes of power supplying.

BATTERY CHANGE:

It is recommended to replace the batteries in all units regularly to

ensure optimum accuracy of these units. (Battery life - see

Specifications below)

Please participate in the preservation of

the environment. Return used batteries to

an authorized depot.

FUNCTION KEYS:

Temperature Station:

The Temperature Station has two easy to use function keys.

MIN/ MAX/ + key

SET/ CH key

SET/CH key (Setting/Channel)

•Press and hold for approximately 3 seconds to enter the

Manual setting mode.

•Press and release to toggle between different channel

readings.

MIN/MAX/+ key (Min/ Max temperature)

•Used to toggle between the minimum and maximum

recorded readings of indoor & outdoor temperature and

indoor humidity.

•Press and hold to reset minimum and maximum record

(when min or max record is shown).

LCD SCREEN AND SETTINGS:

When the signal from the sensor is successfully received by the

Temperature Station, this icon will be switched on. (If not successful,

the icon will not be shown on the LCD). User can therefore easily

see whether the last reception was successful (“ON” icon) or not

Sensor Low

battery indicator

Receiver Lo

battery indicato

Outdoor Reception

Signal icon

Time

Indoor

Temperature in

°F or °C

Indoo

Humidity

%RH

Outdoor Temperature

in °F or °C

Channel No.

(“OFF” icon). On the other hand, the short blinking of the icon shows

that a reception is being done at that time.

For a better display clarity, the LCD screen is split into 3 sections,

showing the information of time, indoor temperature and humidity,

and outdoor data.

Section 1 - TIME

•Display of time (manually set).

Section 2 - INDOOR TEMPERATURE AND HUMIDITY

•Display of indoor temperature and humidity.

Section 3 - OUTDOOR TEMPERATURE

•Display of the outdoor temperature.

MANUAL SETTING:

12 / 24- HOUR TIME DISPLAY SETTING AND TEMPERATURE

UNIT (°C/°F) SETTING

User may choose to display the time in 12-hour or 24-hour mode:

Note:

When the time display is set as 12-hour mode, the temperature unit

will be fixed to °F; when the time mode is in 24-hour format, the

temperature unit will be set to °C.

1. In normal display mode, press and hold the “SET/ CH” key

for approximately 3 seconds. The "12h" or "24h" digit will be

flashing.

2. Press the “MIN/MAX/+” key to set the desired time display

mode.

3. Press and release the “SET/ CH” key to confirm and

advance to the MANUAL TIME SETTING.

MANUAL TIME SETTING

User shall manually set the time of the Temperature Station by the

following steps:

1. The hour digit of the time display will be flashing.

2. Press the “MIN/MAX/+” key to adjust the hour (press and

hold to allow fast advance). Press “SET/ CH” key to confirm

and go to the minute setting.

3. The minute digit will be flashing. Press the “MIN/MAX/+” key

to adjust the minute (press and hold to allow fast advance).

Press “SET/ CH” key once more to return to normal display.

VIEWING THE MINIMUM AND MAXIMUM READINGS:

User may consult the minimum and maximum recordings for indoor

temperature and humidity, and outdoor temperature by following

these steps:

1. Press the “MIN/MAX/+” key once to view the minimum indoor

temperature and humidity and minimum outdoor temperature.

2. Press the “MIN/MAX/+” key once more to view the maximum

indoor temperature and humidity and maximum outdoor

temperature.

Minimum icon

RESETTING THE MINIMUM AND MAXIMUM READINGS:

User may reset the minimum and maximum temperature / humidity

data to the current value by the following steps:

1. Press the “min/max/+” key once to display the minimum data.

2. Press and hold the “min/max/+” key for about 3 seconds to

reset all the minimum / maximum data to the current values

in a single action. (Data of all outdoor and indoor data will be

reset at the same time.)

TEMPERATURE SENSOR:

The outdoor temperature is measured and transmitted to the

Temperature Station every 16 seconds approximately.

The range of the temperature sensor may be affected by the

temperature. At cold temperatures, the transmitting distance may be

decreased. Please keep this in mind when placing the sensor.

915 MHz RECEPTION CHECK

The Temperature Station should receive the outdoor temperature

data within a few minutes after setup. If the temperature data are not

Maximum icon

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology C85845v4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6835 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425BCA Abmessungen

La Crosse Technology

La Crosse Technology 308-1425B Bedienungsanleitung

La Crosse Technology

La Crosse Technology V50-C78861 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7044UA Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7047TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7034TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9023U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2510 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7016U Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7095U Bedienungsanleitung

La Crosse Technology

La Crosse Technology The Weather Channel WS-9005TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2810U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2811U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009-IT Betriebsanleitung

La Crosse Technology

La Crosse Technology C86234 Abmessungen

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9740U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7025TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7208TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WW85784 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung