Larson Electronics EPL-PT-150LED Bedienungsanleitung

EPL-PT-150LED

150W Explosion Proof Adjustable Pole Top Slip Fit Mount LED Fixture

Instruction Manual

Thank you for your purchase of the Larson Electronics EPL-PT-150LED light fixture.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

The Larson Electronics EPL-PT-150LED Pole Top Slip Fitter LED light fixture provides operators with a powerful and

energy efficient alternative to traditional hazardous location luminaries. Cree LED technology and compact design makes

this lamp an excellent replacement upgrade option for bulky and high maintenance cost older fixtures.

MOUNTING

The EPL-PT-150LED pole top slip fit mount explosion proof light features an

adjustable swivel bracket constructed of 3/8" aluminum that allows 270° of

adjustment and is attached to a slip fit yoke for easy installation. The slip fit

yoke is built to customer`s specs, enabling operators to mount this explosion

proof LED light to their specific pole size. The wiring of the EPL-PT-150LED is

terminated in a junction box with 3/4" threaded hub. Operators can run rigid

pipe or flexible conduit to the junction box, terminating the electrical

connections within. Simply slip this fixture over the pole top of choice, and

tighten the T-handle screws to hold the lamp in position. For tilt adjustment,

loosen the adjustment screws at the sides of the trunnion, tilt the light to

desired angle, then tighten again to hold in place.

WIRING

We strongly encourage a licensed electrician install this product, in all locations, especially in outdoor areas where

weatherproofing may be required.

Warning: Check product label for correct input voltage! This fixture is offered

in multiple voltage ratings. Damage may occur if incorrect voltage is applied.

Attach supply line wires to the appropriate light fixture wires as shown

in the applicable diagram 

Secure each pair of wires according to the diagram. Utilize a junction box or similar device and take precautionary steps for

weatherproofing all connections if installed in a location where water may come in contact with the unit. Ensure the unit is

properly grounded and that wiring is done according to all local and national electrical/building codes.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

EPL-PT-150LED

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

PLUG OPERATION

Some models of this fixture will come pre-wired from factory with the selected cord cap. Take precautionary steps for

weatherproofing all connections if installed in a location where water may come in contact with the unit. All outdoor

installations and indoor installations near a wet location require the use of a GFCI device for safety, according to the

National Electrical Code® (NEC). Ensure the unit is properly grounded. Run cable to nearby power source with correct

voltage as identified on product label. Insert and twist-lock explosion-proof plug into a compatible receptacle within the

hazardous environment. Electrical connection between plug and compatible receptacle is accomplished after plug fully

inserts into receptacle and is rotated clockwise.

1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all

the way into receptacle until it cannot go further.

2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also

mechanically locks plug into receptacle so it cannot be pulled out.

3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.

GROUND-FAULT CIRCUIT INTERRUPTER (GFCI)

In the event of a ground fault, a GFCI will trip and quickly stop the flow of electricity to prevent serious injury.

Definition of a ground fault:

Instead of following its normal safe path, electricity passes through a person's body to reach the ground. For example, a

defective appliance can cause a ground fault.

A GFCI receptacle does NOT protect against circuit overloads, short circuits, or shocks. For example, you can still be

shocked if you touch bare wires while standing on a non-conducting surface, such as a wood floor.

NOTE:

GFCI's contain a lockout feature that will prevent RESET if:

• There is no power being supplied to the GFCI.

• The GFCI is miswired due to reversal of the LINE and LOAD leads.

• The GFCI cannot pass its internal test, indicating that it may not be able to provide protection in the event of a ground

fault.

GFCI TEST

Use an approved GFCI tester or plug an electrical device, such as a lamp into the receptacle on which you are working.

Turn the lamp or device ON. Then, press the TEST button on the GFCI box and power should immediately be switched

off. If not, contact an electrician. Press the RESET button to restore power.

MAINTENANCE

Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool downbefore

performing maintenance.

Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

any warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics EXHL-TRN-LE4-FKWL Series Bedienungsanleitung

Larson Electronics

Larson Electronics SPLED-QP-1X10WRE Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-SL-10-20X-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-24-2L-LED-VISRED Bedienungsanleitung

Larson Electronics

Larson Electronics GL-9051-F-M Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-EMG-HB-150LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-48-4L-LED-D-V2-100C Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-C-4XM Bedienungsanleitung

Larson Electronics

Larson Electronics XLE-UVC-XX-SGKT-2X Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-EMG-2X2W-8H Bedienungsanleitung

Larson Electronics

Larson Electronics EPLRL-50-16.4-HR-SWB Bedienungsanleitung

Larson Electronics

Larson Electronics LEDP5W-30-TP1-50CR Bedienungsanleitung

Larson Electronics

Larson Electronics EPEXC-1C-10.3-GFI-50C-BCE Bedienungsanleitung

Larson Electronics

Larson Electronics TPM-2XWP60E-25C Bedienungsanleitung

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-1L Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-50W-120x12-50 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-SL-5-FL26 Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-7WLED-PC-XGFI Bedienungsanleitung

Larson Electronics

Larson Electronics LM-20-3S-EW-LV Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-100-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPLFL-26W-P-LED-25 Bedienungsanleitung

Larson Electronics

Larson Electronics IIND-DBL-36-1L-R1-120V Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-CM Bedienungsanleitung

Larson Electronics

Larson Electronics GL-2051-F-M Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung