Leuze GSU12 Bedienungsanleitung

GSU12

Ultrasonic label fork

Leuze electronic GmbH + Co. KG

[email protected]

In der Braike 1 73277 Owen Tel.: +49 7021 573-0

We reserve the right to make changes – 2020/03/17 – 50143644

www.leuze.com•

1Bildteil

2-7 s

> 12 s

2-7 s

> 12 s

Intended use

The ultrasonic label forks are ultrasonic sensors for contactless detection of the

gap between two consecutive labels on a carrier tape.

NOTICE

Observe intended use!

This product is not a safety sensor and is not intended as personnel

protection.

ÄOnly allow competent persons to put the product into operation.

ÄOnly use the product in accordance with its intended use.

Function and device operation

The label material used determines the achievable precision and the reliability of

gap detection between labels.

– Light switching: signal in the label gap.

– Dark switching: signal on the label.

A Label center position

B Label run

ÄTo achieve a high switching accuracy, place the label tape on the lower fork

with slight tension.

ÄAlign the label tape with the "Label center position" marking.

Overview of operating structure

A Standard function

Normal operation after switch-on

B Manual teach

Can be executed as dynamic teach

C Set switching behavior (light/dark switching)

Standard function

During operation the sensor is always in this function.

The sensor detects label gaps with high precision and speed.

This is indicated by the yellow OUTLED and the switching output.

ONLED

green

Constantly ON when operating voltage is applied.

OUTLED

yellow

Indicates the switching signal.

LED is ON if the sensor detects label gaps.

The display is independent of the output setting.

WARNLED

continuous red

light

OFF: error-free operation.

ON: teaching error caused by unfavorable label material.

Manual teach while the label tape is passing through (dynamic)

Sensor setting via teach button

Preparation: Insert label tape into the sensor.

ÄPress the teach button until the green ON LED and the yellow OUT LED flash

synchronously.

ÄRelease the teach button.

ÄAllow the label tape to advance through the sensor at a maximum speed of

50m/min. The sensor indicates the belt transport by a more rapid synchro-

nous flashing of the green ON LED and yellow OUT LED.

ÄBriefly press the teach button to end the manual teach. The sensor switches

to the standard function.

Approx. 3…7 labels should be advanced through the sensor in order to achieve

stable switching points. The number of labels to be transported is always based

on the material combination.

If the teach event is faulty (e.g. unfavorable material combination, uneven trans-

port, jittering during transport), the red WARNLED illuminates.

ÄRepeat the teach event.

If the fault cannot be rectified, the label material cannot be detected with the de-

vice.

NOTICE

During the manual teach process, a 2-point calibration is performed on

the carrier and the label.

Adjusting the switching behavior of the switching output (light/dark

switching)

ÄPress the teach button until only the green ON LED flashes.

ÄRelease the teach button.

The green ON LED flashes for another 2 seconds and the yellow OUT LED indi-

cates the changed switching behavior for 2 seconds:

– Yellow OUTLED ON: switching output, light switching (signal in the label

gap)

– Yellow OUTLED OFF: switching output, dark switching (signal on the label)

Inhaltsverzeichnis

Andere Leuze Zubehör Handbücher

Leuze

Leuze SET-AC Bedienungsanleitung

Leuze

Leuze GSU14E Bedienungsanleitung

Leuze

Leuze BPS 34 Series Stücklistenhandbuch

Leuze

Leuze DDLS 170 Stücklistenhandbuch

Leuze

Leuze DCR 200i Bedienungsanleitung

Leuze

Leuze BPS 8 SM 102 Bedienungsanleitung

Leuze

Leuze HT25CL2 Bedienungsanleitung

Leuze

Leuze KRT18BW Bedienungsanleitung

Leuze

Leuze LBK S-01 Bedienungsanleitung

Leuze

Leuze IGSU 14E SD Bedienungsanleitung

Leuze

Leuze KRT3CM Series Bedienungsanleitung

Leuze

Leuze KRT18BW Bedienungsanleitung

Leuze

Leuze PRK 55 Ex Series Bedienungsanleitung

Leuze

Leuze GS63B/6.3-S8 Bedienungsanleitung

Leuze

Leuze MLDSET-M1 Bedienungsanleitung

Leuze

Leuze ODSL 30 Bedienungsanleitung

Leuze

Leuze LRS Stücklistenhandbuch

Leuze

Leuze HTU330 Series Bedienungsanleitung

Leuze

Leuze ODS 96 M/V Montageanleitung

Leuze

Leuze ESB2 Series Bedienungsanleitung

Leuze

Leuze IGSU 14E Bedienungsanleitung

Leuze

Leuze GSX14E Bedienungsanleitung

Leuze

Leuze LES 36 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung