Leuze IGSU 14E Bedienungsanleitung

IGSU14E

Ultrasonic label fork

Leuze electronic GmbH + Co. KG

[email protected]

In der Braike 1 73277 Owen Tel.: +49 7021 573-0

We reserve the right to make changes – 2020/05/07 – 50143646

www.leuze.com•

1Figure part

> 12 s

2-7 s

+> 7 s

7-12 s

2-7 s

7-12 s

> 12 s

2-7 s

< 2 s < 2 s

–

> 7 s

HIGH

LOW

≥ 20 ms ≥ 20 ms

Intended use

The ultrasonic label forks are ultrasonic sensors for contactless detection of the

gap between two consecutive labels on a carrier tape.

NOTICE

Observe intended use!

This product is not a safety sensor and is not intended as personnel

protection.

ÄOnly allow competent persons to put the product into operation.

ÄOnly use the product in accordance with its intended use.

Function and device operation

The label material used determines the achievable precision and the reliability of

gap detection between labels.

– Light switching: signal in the label gap.

– Dark switching: signal on the label.

A Label center position

B Label run

ÄTo achieve a high switching accuracy, place the label tape on the lower fork

with slight tension.

ÄAlign the label tape with the "Label center position" marking.

Overview of the operating structure via the teach and minus buttons

A Standard function

Normal operation after switch-on

B easyTeach (while the label tape is passing through)

(2-point calibration on carrier and label)

C Static teach (on the label carrier without transport)

(1-point calibration on carrier)

D Set switching behavior (light/dark switching)

E Deactivate/activate the

ALC

(Auto Level Control) function

(automatic optimization of the switching threshold)

F Manual locking/unlocking of the buttons on the device

IGSU14E standard functions

During operation the sensor is always in this function.

The sensor detects label gaps with high precision and speed.

This is indicated by the yellow OUTLED and the switching output.

ONLED

green

Constantly ON when operating voltage is applied.

OUTLED

yellow

Indicates the switching signal.

LED is ON if the sensor detects label gaps.

The display is independent of the output setting.

WARNLED

continuous red

light

OFF: error-free operation.

ON: teaching error caused by unfavorable label material

ON:

ALC

(Auto Level Control) function is faulty.

ALCLED

yellow

ALC

(Auto Level Control) function is active.

easyTeach while the label tape is passing through (dynamic)

During the

easyTeach

process, a two-point calibration is performed on the carrier

and the label.

NOTICE

With respect to detection reliability, the

easyTeach

process is gener-

ally to be preferred over the static teach process.

Preparation: Insert label tape into the sensor.

ÄPress the teach button until the green ON LED and the yellow OUT LED flash

synchronously.

ÄRelease the teach button.

ÄAllow the label tape to advance through the sensor at a maximum speed of

50m/min.

ðThe sensor indicates the belt transport by a more rapid synchronous

flashing of the green ON LED and yellow OUT LED.

– If sufficient teach values are determined, the sensor automatically terminates

the teach event and goes into standard mode.

The transport of the label tape can be stopped immediately.

– The number of labels to be transported is always based on the material com-

bination. From experience, approximately 2-10 labels should be advanced

through the sensor.

– If the teach event is faulty (e.g., unfavorable material combination, uneven

transport, jittering during transport), the red WARNLED illuminates and the

warning output (if present for the sensor model) is activated.

If the fault cannot be rectified, e.g., via the

easyTune

function, the label ma-

terial cannot be detected with the device.

Static teach on the label carrier without transport

With the static teach process, a one-point calibration is performed on the blank

carrier. This process is especially advantageous because no labels are lost while

teaching.

Preparation: depending on the label size, pull off one or more labels from the car-

rier and insert the blank area into the sensor.

ÄPress the teach button until the green ONLED and the yellow OUTLED flash

alternately.

ÄRelease the teach button.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Leuze Zubehör Handbücher

Leuze

Leuze IGSU 14E SD Bedienungsanleitung

Leuze

Leuze ODS 96 M/V Montageanleitung

Leuze

Leuze PRK 55 Ex Series Bedienungsanleitung

Leuze

Leuze LRS Stücklistenhandbuch

Leuze

Leuze KRT18BW Bedienungsanleitung

Leuze

Leuze HTU330 Series Bedienungsanleitung

Leuze

Leuze ESB2 Series Bedienungsanleitung

Leuze

Leuze DCR 200i Bedienungsanleitung

Leuze

Leuze BPS 34 Series Stücklistenhandbuch

Leuze

Leuze BPS 8 SM 102 Bedienungsanleitung

Leuze

Leuze GSU14E Bedienungsanleitung

Leuze

Leuze MLDSET-M1 Bedienungsanleitung

Leuze

Leuze SET-AC Bedienungsanleitung

Leuze

Leuze GSU12 Bedienungsanleitung

Leuze

Leuze KRT18BW Bedienungsanleitung

Leuze

Leuze LES 36 Series Bedienungsanleitung

Leuze

Leuze GS63B/6.3-S8 Bedienungsanleitung

Leuze

Leuze GSX14E Bedienungsanleitung

Leuze

Leuze KRT3CM Series Bedienungsanleitung

Leuze

Leuze ODSL 30 Bedienungsanleitung

Leuze

Leuze LBK S-01 Bedienungsanleitung

Leuze

Leuze DDLS 170 Stücklistenhandbuch

Leuze

Leuze HT25CL2 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung