Lifecanvas Technologies SMARTLABEL Bedienungsanleitung

SMARTLABEL

Quick Installation Guide

POWER CABLE (1)

INFO@LIFECANVASTECH.COM

LIFECANVASTECH.COM

1Carefully remove SmartLabel, the SmartBox, and the SmartBox+ from the packaging and place

at the installation location. We recommend at least 8 inches of space around the devices for

proper airﬂow, and a level surface. Locate the parts listed below.

Connect the cable originating from the ‘Cooling Unit’ port on

SmartBox+ to SmartLabel. Similarly, connect the cable from

the ‘Alternating’ port on SmartBox to SmartLabel. Do the

same for the ‘Direct’ cable. Attach the main power cable to

the rear side of SmartBox and plug it into an outlet with the

correct voltage requirements.

SAMPLE CUPS (2)

AND MESH INSERTS

SAMPLE CHAMBER COVERS (2)

ALIGN TABS AND

PLUG IN CABLE

SCREW BEARING

LOCK NUT

CLOCKWISE

COMPLETELY.

SCREW BEARING

EXTRA FUSES (2)

SAMPLE

CHAMBER

SPACERS (4)

SMARTBOX SMARTLABEL

SMARTBOX+

INSERT

POWER

CORD

SMARTBOX

SMARTBOX+ SMARTLABEL

COOLING UNIT

ALTERNATING DIRECT

INFO@LIFECANVASTECH.COM

LIFECANVASTECH.COM

2Open the lid to SmartLabel. Identify the two black screw-top lids to the solution reservoirs at the

front, and the two translucent plastic sample chambers towards the back. The left-side reservoir

and chamber comprise side ‘A’, and the right-side reservoir and chamber comprise side ‘B’.

Identify the two gaps in the

plastic (red arrows) located

halfway along the length of

the sample chamber.

Plastic spacers, which control the solution level in the front half of

the chamber where the sample cup is placed, need to be lowered

into place on each side of the chamber, as shown in the left image

above.

Open the lid to

SmartLabel

. Identify the two black screw-top lids to the

solution reservoirs

front, and the two translucent plastic

sample chambers

towards the back. The left-side reservoir

and chamber comprise side ‘

’, and the right-side reservoir and chamber comprise side ‘

SAMPLE CHAMBERS

SOLUTION RESERVOIRS

SIDE B

SIDE A

3Turn the physical power switch on the rear side of the SmartBox from O to I to power up the

system.

INFO@LIFECANVASTECH.COM

LIFECANVASTECH.COM

4There are drainage tubes located under the panel at the bottom front of SmartLabel, with the

one on th eleft connected to reservoir A and the one on the right to reservoir B. In the left image

below, the stopcock is in the closed position. In the right image, the stopcock is in the open

position, enabling drainage.

5Making sure both stopcocks are in the closed position, pour 500 mL of deionized water into each

solution reservoir, A and B. Secure each reservoir lid when done.

INFO@LIFECANVASTECH.COM

LIFECANVASTECH.COM

6When performing an experiment, a sample is loaded into an insert that is lowered into the sample

cup, which is then gently inserted into the hexagonal slot on the ﬂoor of one of SmartLabel’s

sample chambers as shown below.

7SmartBox’s touchscreen display is used to operate SmartLabel and control all of the settings

available to users. When performing a real experiment, the following should be toggled on by

pressing the gear icon ( ) under the respective headings: sample cup Rotation, sample cup

Stirrer, and pump Power. Finally, stochastic electrotransport-mediated labeling functionality is

turned on using the bottom-rightmost button, and is not activated until the lid to SmartLabel is

closed.

8When ﬁnished testing or using SmartLabel, turn o electrophoresis, turn o the pumps (which

should not be run without liquid present), drain the liquid from the reservoirs as shown in Step 4,

and then power-down the system using the knob on the rear side of the SmartBox (from Step 3).

pressing the gear icon ( ) under the respective headings: sample cup Rotation, sample cup

Inhaltsverzeichnis

Andere Lifecanvas Technologies Laborausrüstung Handbücher

Lifecanvas Technologies

Lifecanvas Technologies SmartBatch+ Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung