Lifetime CRANK ADJUST 90569 Bedienungsanleitung

Icon Legend................................2

Notices....................................3

Initial Setup...............................4

Pole Assembly.............................7

Extension Arm Assembly............10

Handle Assembly......................14

Backboard to Rim Assembly........17

Parts Identiﬁer..........................i-iv

Backboard to Pole Assembly.......24

Final Assembly..........................27

Maintenance Instructions..........32

Registration........................33

Warning Sticker........................34

Warranty................................35

TABLE OF CONTENTSTOOLS REQUIRED

3/4" (x2)

5/16"

(x1, included) Rubber Mallet

Electric Drill

Carpenter’s Level Shovel

(80 lb bag x 8)

Cement

Tape Measure

1/2" (x2)

3/8"

(x1, included)

9/16" (x2)

CONTACT LIFETIME CUSTOMER SERVICE:

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

QUESTIONS? Model Number: 90569

Product ID:

For Customer Service in Mainland

Europe and the United Kingdom,

E-mail:[email protected]

Live Chat: www.lifetime.com

(click on “Live Chat” tab)

Video Instructions:

www.youtube.com/lifetimeproducts

Pour le français, voir la page 2. Para el español, ver la página 3.

ASSEMBLY INSTRUCTIONS

MODEL 90569

CRANK ADJUST®

BASKETBALL SYSTEM

• Assembly requires at least eight 80-lb. bags of

concrete mix. Before digging, call to locate any

buried utility lines.

• 3+ people recommended for setup.

BEFORE ASSEMBLY:

Save this instruction in the event

that the manufacturer has to be

contacted for replacement parts.

GET ASSEMBLY HELP

WATCH THE INSTRUCTIONAL VIDEOS ON YOUTUBE

Scan the code, or search http://go.lifetime.com/90569playlist

COPY

1189602 B 2/11/2019

• Indicates the parts to be used for a section.

• Indicates special heed should be taken when reading.

• Indicates the hardware to be used for a section.

• Indicates the tools to be used for a section.

• Indicates no hardware required for a speciﬁc page.

• Indicates no parts required for a speciﬁc section.

• Indicates to use/not to use an electric drill for a speciﬁc step.

ICON LEGEND

• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten.

This hardware was designed with this feature in order to prevent loosening later.

COPY

WARNINGS & NOTICES

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁer and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Three capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.

• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.

SAFETY INSTRUCTIONS

COPY

Metal Parts

AEZ (x4)

AEI (x4)

Carpenter’s Level Shovel

(80 lb bag x 8)

Cement / Cemento / Ciment

Tape Measure

3/4"

(x2)

Hardware Blister Pack

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

INITIAL SETUP

AOE (x8)

AE0 (x1) CYV (x1)

AKT (x1)

FNG

COPY

TOOLS AND HARDWARE REQUIRED

XSECTION 1 (CONTINUED) 1

• Dig a hole 30” (76.2 cm) deep and 21” (53 cm) square. The edge of the hole should be ﬂush with the edge of the

playing court. If you live in an area where frost heaves may pose a problem, consult your local building inspector to

determine the appropriate hole depth. Bell out the bottom of the hole as illustrated. We recommend building a form

to keep the top of the concrete level and square. Place the form so it is level with the playing surface.

21”

30”

21”

Before digging, call to locate any buried utility lines.

CAUTION

3/4” (x2)

1.1

!• There must be a 3’ (92 cm) area

behind the pole to allow the user to

adjust the Rim height.

1.2

AEI

AOE

AOE (x8)

• Thread a 1/2” Hex Nut (AOE) all the way onto each J-Bolt (AEI). Slide the threaded ends of the J-Bolts through the corner

holes in the Template (AKT), and secure them completely with 1/2” Hex Nuts (AOE). Insert the Bolt (AEO) through the center

hole in the Template and tighten the Nut Coupler (CYV) onto the Bolt as far as it will go.

AKT

CYV

AOE AOE

AOE

AEO

!• Ensure the curved ends of the

J-Bolts point outward away from the

corners as shown.

TOOLS AND HARDWARE REQUIRED

XSECTION 1 (CONTINUED)

• Center the Template (AKT) over the hole. Insert the

J-Bolts (AEI) into the concrete and agitate the Template

assembly to eliminate any air bubbles. Push the

J-Bolts into the cement until the Template is

resting ﬂat against the cement. Form the cement

into a downward slope toward the playing surface

to allow water runoff. The lower four Hex Nuts (AOE)

will be in the concrete permanently. Clean off any

concrete on the Template or the exposed portion

of the J-Bolts. Using a carpenter’s level, ensure the

Template is square to the playing surface. Plate should

be level and about 1/2” above the playing surface

for water to drain off of the steel.

18” (20 cm)

AEZ

(80-lb Bag x 8)

• If you are using concrete mix, mix the concrete

according to the instructions on the bags. Please

note that a thicker mix of concrete will dry stronger.

Pour the concrete into the hole, stopping about

18” (46 cm) from the top of the hole. Push the

four pieces of 24” Rebar (AEZ) ﬁrmly to the bottom

of the hole. The Rebar should be arranged in a

square about 8” (20 cm) wide in the center of

the hole so each piece will be next to a J-Bolt

when it is placed in the cement. Finish ﬁlling

the hole to the top with concrete. The top of the

concrete should extend about 1/2” (13 mm)

above the playing surface and slope downward

toward the playing surface to allow water runoff.

1.3

!• You are now ﬁnished with the initial assembly steps. DO NOT

PROCEED WITH THE ASSEMBLY until the concrete has fully cured.

Curing will take a minimum of 72 hours (3 days). In humid climates

or wet weather, allow additional time for the concrete to cure. Never

use the system without ﬁrst following the cementing instructions.

1.4

AKT

AEI

AOE

Playing surface

Hardware Blister Pack

HARDWARE REQUIRED

POLE ASSEMBLY

CMV (x1)

EJG (x2)

CUB (x2)

BCO

PARTS REQUIRED

ALH (x1)

ALE (x1)

EJS (x2)

Large Parts

TOOLS REQUIRED

9/16" (x1)

5/16"

(x1, included)

EJH (x4)

Electric Drill

ELW (x1)

TOOLS AND HARDWARE REQUIRED

XSECTION 2 (CONTINUED)

2.1

The gussets and small

hole face the same

direction

WARNING

The Poles must be seated together! Even if the Poles cover

the slots before seating, they must be struck on a hard

surface three times! Failure to seat the Poles correctly

could allow the Poles to separate during use, which could

lead to serious personal injuries or property damage.

2.2 • Raise the pole assembly about 12 inches off

the ground. Strike the end of the poles against

a piece of scrap wood or thick cardboard three

times to ensure the poles are seated properly.

WARNING

Do not hit your feet with the Pole Sections, as

serious injury could occur.

ALH

ALE

• Slide the ﬂared end of the Top Pole (ALH) onto

to the swaged end of the Bottom Pole (ALE). The

small hole in the bottom of the Top Pole should

face away from the playing surface.

small

hole

• If you have trouble with this section, scan the QR code to view a video on how to assemble the Pole.

• http://go.lifetime.com/crankadjustpole

TOOLS AND HARDWARE REQUIRED

XSECTION 2 (CONTINUED)

• Attach the Pole Brackets (EJS) to the Top Pole (ALH) with the hardware shown.

CMV (x1)

CMV

2.3 • Use an electric drill to secure the Top Pole to the Bottom Pole using a Self-Tapping Screw (CMV). You may need to

use a hex driver or chuck the Self-Tapping screw directly into an electric drill.

9/16"

5/16"

EJG (x2)

EJG

ALH

EJG

CUB (x2) EJH (x4)

EJH

EJH CUB

EJS

CUB

EJH

2.4

CUG (x2)

AEG (x4)

CYF (x2)

EJM (x2)

EJL (x1)

DIQ (x4)

CZF

Hardware Blister Pack

HARDWARE REQUIRED

EXTENSION ARM ASSEMBLY

CUB (x1)

AKE (x1)

Metal Parts

TOOLS REQUIRED

PARTS REQUIRED

AKD (x2)

3/4"

3/8" (included)

9/16"

5/16" (included)

Rubber Mallet

AOQ (x1)

Inhaltsverzeichnis

Andere Lifetime Sport & Outdoor Handbücher

Lifetime

Lifetime SPEED SHIFT Bedienungsanleitung

Lifetime

Lifetime 90703 Bedienungsanleitung

Lifetime

Lifetime 90183 Bedienungsanleitung

Lifetime

Lifetime 1306 Datenblatt

Lifetime

Lifetime 1221 Bedienungsanleitung

Lifetime

Lifetime 90144 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90757 Bedienungsanleitung

Lifetime

Lifetime 90056 Bedienungsanleitung

Lifetime

Lifetime 91009 Bedienungsanleitung

Lifetime

Lifetime QUICK ADJUST 1044 Bedienungsanleitung

Lifetime

Lifetime 91062 Bedienungsanleitung

Lifetime

Lifetime 90010 Bedienungsanleitung

Lifetime

Lifetime 90466 Bedienungsanleitung

Lifetime

Lifetime SPEED SHIFT 51544 Bedienungsanleitung

Lifetime

Lifetime IN-GROUND POWER LIFT 90962 Bedienungsanleitung

Lifetime

Lifetime ACTION GRIP Bedienungsanleitung

Lifetime

Lifetime 73729 Kurzanleitung

Lifetime

Lifetime FRONT ADJUST 90607 Bedienungsanleitung

Lifetime

Lifetime 91153 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 71524 Bedienungsanleitung

Lifetime

Lifetime POOLSIDE 1301 Bedienungsanleitung

Lifetime

Lifetime ACTION GRIP 1084 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 91002 Bedienungsanleitung

Lifetime

Lifetime SPEED SHIFT 90812 Bedienungsanleitung

Beliebte Sport & Outdoor Handbücher anderer Marken

Flybar

Flybar POGO TRICK BOARD Bedienungsanleitung

Crivit

Crivit 93713 Bedienungsanleitung

Hudora

Hudora 76171 Montageanleitung

Axler

Axler GSU-1 Bedienungsanleitung

Aquaglide

Aquaglide FREEFALL 6 LANDING PAD Bedienungsanleitung

Cap Strength

Cap Strength POWER RACK FM-CS7000F Bedienungsanleitung

La Sportiva

La Sportiva RACE BORG Bedienungsanleitung

Crivit

Crivit 302640 Bedienungsanleitung

Sportime

Sportime Equalizer Bedienungsanleitung

T&R Sports

T&R Sports 5FT FOOSBALL TABLE Bedienungsanleitung

Salewa

Salewa VERT Bedienungsanleitung

KICK

KICK Decagon Bedienungsanleitung

byox

byox FJ-4.5FT Bedienungsanleitung

CHINESPORT Spa

CHINESPORT Spa 01325 Bedienungsanleitung

AXI.COM

AXI.COM ConesPro101 Bedienungsanleitung

Insportline

Insportline IN 2052 Bedienungsanleitung

Rugged Interactive

Rugged Interactive CardioWall Compact Kurzanleitung

N-FLATABLES

N-FLATABLES Belly Bouncer Fire Dog Bedienungsanleitung