LMI Technologies Gocator 2075 Bedienungsanleitung
Gocator 2075
Version 3.5.2.123 Revision: A
Copyright, © 2012, LMI Technologies, Inc. All rights reserved.
Proprietary
This document, submitted in confidence, contains proprietary information which shall not
be reproduced or transferred to other documents or disclosed to others or used for
manufacturing or any other purpose without prior written permission of LMI Technologies
Inc.
No part of this publication may be copied, photocopied, reproduced, transmitted,
transcribed, or reduced to any electronic medium or machine readable form without prior
written consent of LMI Technologies, Inc.
Trademarks and Restrictions
Gocator™ is a registered trademark of LMI Technologies, Inc. Any other company or
product names mentioned herein may be trademarks of their respective owners.
Information contained within this manual is subject to change.
This product is designated for use solely as a component and as such it does not comply
with the standards relating to laser products specified in U.S. FDA CFR Title 21 Part
1040.
Contact Information
For more information, please contact LMI Technologies.
LMI Technologies, Inc.
1673 Cliveden Ave.
Delta,
BC V3M 6V5 Canada
Telephone: +1 604 636 1011
Facsimile: +1 604 516 8368
www.lmi3D.com
Table of Contents
1Introduction............................................................................................................................. 4
2Rut Scanning System Setup..................................................................................................... 5
2.1 Layout...............................................................................................................5
2.2 System Setup....................................................................................................5
2.3 Software Configuration......................................................................................6
3System Operation .................................................................................................................... 7
4Specifications .......................................................................................................................... 8
4.1 Field of View / Measurement Range..................................................................8
4.2 Dimensions.......................................................................................................9
4.3 Envelope.........................................................................................................10
Introduction
1 Introduction
This document provides supplementary information for using Gocator 2075.
Reader should refer to Gocator user manual and quick start guide for descriptions and
safety precautions of Gocator. Cited sections from the User Manual are shown in italics.
Rut Scanning System Setup
2 Rut Scanning System Setup
2.1 Layout
The Gocator 2075 is designed to cover a scan width of up to 4.2m by using 8 sensors
mounted in parallel.
A Gocator 2075 for rut scanning should typically set the clearance distance (CD) to
800mm and measurement range (MR) to 625mm. With this combination, the FOV and
resolutions are:
Specifications
CE
FE
FOV
430.39
758.34
X-Resolution
0.67
1.18
Z-Resolution
0.16
0.44
Users can use the specification estimator (Gocator-2075_Specification_Estimator.xlsx)
to calculate the X and Z resolution of the sensors with different combination of clearance
distance and measurement range.
2.2 System Setup
A typical Gocator 2075 system is setup as a multi-sensor system. The sensors are
powered up using a Master 400/800/1200/2400.
To wire up a Gocator 2075:
1. Connect the Gocator Power to Master cordset between the Power connector and
an unused port on the Master.
2. Connect the Gocator Ethernet cordset between the LAN connector and an
Ethernet switch.
Refer to the Master 400/800 and the Master 1200/2400 sections for more information on
how to install a Master.
2.3 Software Configuration
Each sensor is shipped with the default IP address of 192.168.1.10. Before putting a
sensor into a multi-sensor system, its firmware version must match with that of the other
sensors and its IP address must be unique.
To configure a Gocator 2075 for the first time:
1. Setup the sensor’s IP address.
a. Follow the steps in the Running a Standalone Sensor System section.
b. Make sure that there is no other sensor in the network with the IP address
192.168.1.10.
2. Upgrade the firmware.
a. Follow the steps in the Firmware Upgrade section.
b. Visit http://www.lmi3d.com/product/gocator-2000-family/support/files/all to
download the latest firmware.
3. Setup profiling parameters.
a. Follow the steps in the Setup and Calibration chapter on how to setup
profiling parameters. Typically Trigger, Active Area and Exposure will
need to be adjusted.
System Operation
3 System Operation
The isolated layout should be used. Under this layout, each sensor can be
independently controlled by the SDK. The following application notes explain how to
operate a multi-sensor system using the SDK.
Gocator-2000-2300_Appnote_Multi-Sensor-System_R1.0.zip
Explains how to use the SDK to create a multi-sensor system, and multiplex their timing.
Gocator-2000-2300_Appnote_Multi-Sensor_Alignment_Calibration_R1.0.zip
Explains how to use the SDK to perform alignment calibrate a multi-sensor system.
Example code is included with both of the above application notes.
Specifications
4 Specifications
4.1 Field of View / Measurement Range
4.2 Dimensions
4.3 Envelope
Inhaltsverzeichnis
Andere LMI Technologies Scanner Handbücher
LMI Technologies
LMI Technologies MikroCAD premium Bedienungsanleitung
LMI Technologies
LMI Technologies HDI 109 Bedienungsanleitung
LMI Technologies
LMI Technologies chroma+scan 20 0 Series Bedienungsanleitung
LMI Technologies
LMI Technologies MikroCAD premium Bedienungsanleitung
LMI Technologies
LMI Technologies Gocator 1300 Bedienungsanleitung
LMI Technologies
LMI Technologies MikroCAD Bedienungsanleitung
LMI Technologies
LMI Technologies Chroma+scan 21X5 Bedienungsanleitung
LMI Technologies
LMI Technologies HDI 100 Series Bedienungsanleitung
LMI Technologies
LMI Technologies HDI 120 Bedienungsanleitung
LMI Technologies
LMI Technologies FocalSpec Bedienungsanleitung
